Audiovox Pursuit PRO-9556 User manual

128-7769
1 of 2
3 Channel Remote
Car Starter
FEATURES :
2 Three Button Programmable RF Transmitters
Three Channel Receiver (capable of accepting 4 transmitters)
Keyless Entry Outputs (+) and (-)
On-Board Start Relay
On-Board Accessory Relay
On-Board Ignition 1 Relay
On-Board Ignition 2 Relay
Ignition 2 Relay Selectable On or Off During Cranking
On-Board Parking Light Relay
Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
Tach Signal Learning Circuit
Two ( + ) and Two ( - ) Safety Shutdown Circuits
Alarm By-Pass Output
AccessoryOutputs
(PulseBefore&AfterStart,DuringCrank&AfterShutDown)
Selectable Steady or Flashing Parking Lights for Run Indication
Selectable 5, 10, 15, 20 Minute Run Time
Selectable 1 Sec., 3.5 Sec., or 1 Sec./Dbl 1 Sec. Door Lock Output Pulse
Car Finder Mode
Model PRO-9556
OwnersManual

128-7769
2 of 2
© 2006 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-7769
KEYLESSENTRY 1. The Lock button on the transmitter is used to lock the vehicle's doors,
the Unlock button is used to unlock the vehicle's doors. To lock or unlock
the doors simply press and release the desired function button one time.
As a keyless entry unit, for your convenience, the parking lights will
flash once when the doors are locked and twice when the door are
unlocked.
REMOTECARFINDER
The Lock or Unlock buttons are also used to access the car finder mode.
This feature is particularly useful in a crowded parking lot where finding
your car may be difficult. To access the car finder mode, while within
range of your car, simply press and hold either the lock or unlock button of your trans-
mitter for three seconds. The parking lights will begin to flash making your vehicle
more visible. The lights will stop automatically after 30 seconds. If you wish to turn
off the car finder mode prior to the expiration of the 30 second timer, press and release
either the lock or unlock button of your transmitter one time
REMOTE STARTING THE VEHICLE
This unit will not start the vehicle if any one of the following situations exists;
The vehicle's hood lid is opened. The gear shift selector is not in Park.
The brake pedal is depressed. The safety control switch is in the Off position.
1. To start the vehicle, press and release the Key/Trunk button two times within 2 seconds.
The vehicle will start and remain running for the pre-programmed 5,10,15,20 minute run
cycle. As a visual indication, the parking lights will flash or remain on depending on the
setting by your installation center.
2. When you arrive at the vehicle, turn the ignition key to the ON position (not the spring
loaded start position), then step on the brake pedal to disengage the remote starter. The
vehicle will continue to run, but now on it's own power.
NOTE: The engine will stop running before the pre-programmed run cycle has expired if
you perform any one of the following functions;
Press and release Key/Trunk button on the keychain transmitter two times within 2
seconds.-Depress the brake pedal. - Open the vehicle's hood -Place the unit in
the safety control disabled mode.
PRLED SAFETY CONTROL SWITCH
The Push-Button LED control switch allows you to temporarily disable the remote starting function of the
system. This recommended whenever the vehicle is being serviced. To place the system in the service
mode:
1) With the system disarmed/unlocked, and the ignition switch off Press and Hold the PRLED on.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED begins to flash two short flashes followed by one long flashes and continues this pattern
until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start is in the service mode
and will not start from RF or any other input Posse or otherwise.
To Exit R/S Override Mode
1) With the system disarmed, Press and Hold the PRLED on.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED turns off indicating that the R/S unit is fully functional one again.
FUNCTION SETTING CHART
To be completed by installer
Run Time 5 Min 10 Min 15 Min 20 Min 
Door Lock Timer 1 Sec/1 Sec 3.5 1 Sec/Dbl 1 Sec 
Lights Pulse Steady 