Audiovox FPE2705 User manual

COLOR TELEVISION
(LC27K6)
FPE2705

CONTENTS
Safety instructions………………………………………………………………………..…
Instructions on adjusting and testing …………………………….…….………………….…
Trouble shooting ……………………………………………………….……………………
Principle analysis ………………………………………….…….……………..................
Block diagram……………………………….………….………….................................
IC Block diagram…………………………………..………………………………..………..9
Wiring diagram..........................................................................................................
Identification criteria for the bright spot and dark spot of the LCD screen................
Exploded view………..…...........................................................................................
Part list ……………………………………………………………..……………...............
Schematic diagram.………………………………………………………………..…….....
1
3
5
7
8
9
13
15
16
18
45

1
Safety instructions
1 Instructions
1.1 Be sure to switch off the power supply before replacing or welding any components or
inserting/plugging in connection wire
1.2 Anti static measures to be taken (throughout the entire production process!):
1.2.1 Do not touch here and there by hand at will;
1.2.2 Be sure to use anti static electric iron;
1.2.3 It’s a must for the welder to wear anti static gloves.
1.3 Please refer to the detailed list before replacing components that have special safety requirements.
Do not change the specs and type at will.
2 Points for attention in servicing of LCD
2.1 Screens are different from one model to another and therefore not interchangeable. Be sure to use
the screen of the original model for replacement.
2.2 The operation voltage of LCD screen is 700-825V. Be sure to take proper measures in protecting
yourself and the machine when testing the system in the course of normal operation or right after
the power is switched off. Please do not touch the circuit or the metal part of the module that is in
operation mode.
Relevant operation is possible only one minute after the power is switched off.
2.3 Do not use any adapter that is not identical with the TV set. Otherwise it will cause fire or damage to
the set.
2.4 Never operate the set or do any installation work in bad environment such as wet bathroom, laundry,
kitchen,or nearby fire source, heating equipment and devices or exposure to sunlight etc. Otherwise
bad effect will result.
2.5 If any foreign substance such as water, liquid, metal slices or other matters happens to fall into the
module, be sure to cut the power off immediately and do not move anything on the module lest it
should cause fire or electric shock due to contact with the high voltage or short circuit.
2.6 Should there be smoke, abnormal smell or sound from the module, please shut the power off at once.
Likewise, if the screen is not working after the power is on or in the course of operation, the power
must be cut off immediately and no more operation is allowed under the same condition.
2.7 Do not pull out or plug in the connection wire when the module is in operation or just after the power
is off because in this case relatively high voltage still remains in the capacitor of the driving
circuit.Please wait at least one minute before the pulling out or plugging in the connection wire.
2.8 When operating or installing LCD please don’t subject the LCD components to bending, twisting or
extrusion, collision lest mishap should result.
2.9 As most of the circuitry in LCD TV set is composed of CMOS integrated circuits, it’s necessary to pay
attention to anti statics. Before servicing LCD TV make sure to take anti static measure and ensure
full grounding for all the parts that have to be grounded.
Attention: This service manual is only for service personnel to take reference with. Before servicing
please read the following points carefully.

2
2.10 There are lots of connection wires between parts behind the LCD screen. When servicing or
moving the set please take care not to touch or scratch them. Once they are damaged the screen
would be unable to work and no way to get it repaired.
2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead to
breakage of screen glass or damage to driving circuit.
Therefore it must be packed in a strong case before the transportation or handling.
2.12 For the storage make sure to put it in a place where the environment can be controlled so as to
prevent the temperature and humidity from exceeding the limits as specified in the manual. For
prolonged storage, it is necessary to house it in an anti-moisture bag and put them altogether in one
place. The ambient conditions are tabulated as follows:
Temperature Scope for operation 0—+50 C
Scope for storage -20—+60 C
humidity Scope for operation 20%—85%
Scope for storage 10%—90%
2.13 Display of a fixed picture for a long time may result in appearance of picture residue on the screen,
as commmonly called “ghost shadow”. The extent of the residual picture varies with the maker of
LCD screen. This phenonmenon doesn’t represent failure. This “ghost shadow” may remain in the
picture for a period of time (several minutes).But when operating it please avoid displaying still
picture in high brightness for a long time.
3. Points for attention during installation
3.1 The front panel of LCD screen is of glass. Wheng installing it please make sure to put it in place.
3.2 For service or instatallation it’s necessary to use specified screw lest it should damage the screen.
3.3 Be sure to take anti dust measures. Any foreign substance that happens to fall down between the
screen and the glass will affect the receiving and viewing effect
3.4 When dismantling or mounting the protective partition plate that is used for anti vibration and
insulation please take care to keep it in intactness so as to avoid hidden trouble.
3.5 Be sure to protect the cabinet from damage or scratch during service, dismantling or mounting.

3
Instructions on adjusting and testing
PM5518(Video signal generator),K-7253(VGA signal generator),CA210(White balancer
2.1.Adjustment and calibration flow process
For adjustment and calibration flow process diagram, see figure 1
Figure 1
2.2 Adjustment and calibration of complete set
Connect different CPU board and analog board according to connection diagram 203-L27K60-01JL.
Put power supply on, see if the display is normal.
Method to enter factory menu: Continuously push “VOL+” “Mute” and “Video” keys to enter the
factory menu; select different items of adjustment and calibration, when the first line of each adjustment
item is in high brightness; push the “ENTER” key to select different adjustment item; push “ENTER” key
after the mode is selected with VGA input and select three color temperatures 6500K,9300K,12000K;
push “MENU” to quit the factory menu.
Check CPU and analog board
Combined test for general assembly
Preset before outgoing from factory
Connect to central signal source, check if various TV functions
(station skipping, modulate quantity control etc), check if the
output of earphone and speaker are normal
Input AV/S, HDTV signal and check various
functions under terminals
Input VGA signal (one format) and check if display is
normal in the state of PC and various functions (analo
g
quantity control, line/field center etc.)
Check accessories and then packing
Figure 1 Flow process ofAdjustment and calibration

4
Note: The white balance adjustment should be made in the mode of “Nature” picture.
2.2.1 EPROM Initialization
Enter the first page of factory menu, push “ENTER” key after the selecting
Clear EEPROM, shut off the power supply after the appearance of “OK”.
2.2.2 VGAand DV1 channels adjustment
2.2.2.1 VGAchannel mode preset
Input VGA signal of K-7253(PATTERN 5:Final Test),select TIME301 (640*350/70Hz), push ”AUTO”
key to automatically adjust to make the picture full of the screen, same, to automatically adjust
respectively TIME302 (720*400/70Hz) ,TIME303 (640*480/60Hz), TIME311 (800*600/60Hz), TIME313
(1024*768/60Hz), TIME315 (640*480/75Hz), TIME316 (800*600/75Hz), TIME317 (1024*768/75Hz),
TIME319 (1280*1024/75Hz), and TIME339 (1280*1024/60Hz).
2.2.2.2 ADC adjustment of VGAchannel
Input the signal of 64 grades of grey density to K-7253 TIME311, PATTERN474, set the adc-gain to
max.(Not exceeding 18) so that the brightest two grades are distinguishable.
2.2.2.3. White balance adjustment of VGA and DV1 channels
Input the signal of 8 grades of grey density to K-7253 TIME311,PATTERN471, enter the adjustment
menu of white balance. Use the white balance to adjust second and seventh grades.
Select mode to be 6500K,adjust offset_R, offset_G, offset_B, to adjust the second grade color
coordinate to be 313,329 and the brightness to be about 3.5 nit. Adjust gain_R, gain_G, gain_B so that
seventh grade color coordinates are 313,329. Adjust offset_R, offset_G, offset_B and gain_R, gain_G,
gain_B,again and again until two grads of grey density are all set to 313,329.
Select mode to be 9300K,adjust offset_R, offset_G, offset_B,so that the second grade color
coordinates are 285,293 and the brightness about 3.5 nit.Adjust gain_R, gain_G, gain_B so that seventh
grade color coordinates are 285, 293. Adjust offset_R, offset_G, offset_B and gain_R, gain_G, gain_B,
again and again until two grads grey density are all set to 285,293.
Select mode to be 12000K.Adjust offset_R, offset_G, offset_B,so that the second grade color
coordinates are 270,283 and the brightness about 3.5 nit. Adjust gain_R, gain_G, gain_B, so that the
seventh grade color coordinates are 270, 283. Adjust offset_R, offset_G, offset_B and gain_R, gain_G,
gain_B, again and again until two grads grey density are all set to 270,283.
Notice: The value of gain_R, gain_G, gain_B should not exceed 128, and at least one of the
values should be guaranteed to be 128
2.2.3 TV channel adjustment
2.2.3.1 Adjustment of VCO, OPTION, sub-brightness and sub-contrast
Input the AV color bar signal(PM5518 COLOUR BAR 100%)to VIDEO 1 terminal, enter the first
page of factory menu. Select auto color, push key “ENTER”. About two seconds later, OK is displayed,
showing the adjustment is over. Adjust the value of Option to be 11,S-bright to be 124,S-contrast to be
140, and Max Volume to be 30.
2.2.3.2 White balance adjustment of TV channel
Input AV signal (PM5518,NTSC system, eight grades of grey density signal), enter the adjustment
menu of white balance.Use the white balancer to adjust the second and seventh grades.Adjust offset_R,
offset_G, offset_B,so that the second grade color coordinates are 255,240 and the brightness about 3.5
nit. Fix gain_B to be 128, adjust gain_R, gain_G, so that the seventh grade color coordinates are 290,
285. Adjust offset_R, offset_G, offset_B and gain_R, gain_G again and again until two grads of grey

5
density are all set to regulated value.
2.2.4 White balance adjustment of YprPb channel
Input YPbPr signal of K-7253 to D4-1 terminal,input eight grades of grey density signal of
TIME380(480i)PATTERN471, adjust S-bright to be 120,S-contrast to be 140. Enter the adjustment menu
of white balance,adjust second grade with balancer. Adjust offset_R, offset_G, offset_B sot that the
second grade color coordinates are 255,240 and the brightness about 3.5 nit.
Separately input eight grades of grey density signal of mode TIME392(480p),TIME394(720p)and
TIME396(1080i). Repeat the above operation, so that the second grade color coordinates are 255,240
and the brightness about 3.5 nit.
3. Function inspection
3.1 TV function
Enter the search menu →auto search, connect RF-TV terminal to the central signal source, check if
there is station skipping.
3.2 AV/S, HDTV terminal
ConnectAV/S and HDTV signal, check if they are normal.
3.3 VGA connector
Insert VGA signal connector, input format signal 640 x 480@60 Hz VGA, check if the display is
normal. If there is interfere in picture, push the adjustment key on the remote control set one more time,
check if the display is normal.
3.4 Sound channel inspection
Check if the output of each speaker and earphone channel is normal.
3.5 For factory preset, see table. 1
Trouble shooting
Before servicing please check to find the possible causes of the troubles according to the table below.
1.Antenna:
Picture is out of focus or jumping  Bad status in signal receiving
 Maybe broadcast signal itself is not good
 Check if the outdoor antenna is disconnected.
 Check if the antenna is correctly oriented.
Fringe in picture  Check if the antenna is correctly oriented.
 Maybe there is electric wave reflected from hilltop or building.
Picture is interfered by stripe
shaped bright spots
 Possibly due to interference from automobile, train, high
voltage transmission line, neon lamp etc.
 Maybe there is interference between antenna and power
supply line. Please try to separate them in a longer distance.
There appear streaks or light color
on the screen
 Check if interfered by other equipment and if interfered
possibly by the equipment like transmitting antenna, non
professional radio station and cellular phone.

6
2.TV set:
No picture and sound, but only hash.  Check if the antenna cable is correctly connected, or if it has received
the video signal correctly.
Blur picture  Check if the antenna cable is correctly connected.
 Of if it has received the right video signal.
Symptoms Possible cause
Unable to switch the power on  Check to see if the power plug has been inserted properly into the
socket.
No picture and sound  Check to see if the power supply of liquid crystal TV has been
switched on. (as can be indicated by the red LED at the front of the
TV set)
 See if it’s receiving the signal that is transmitted from other source
than the station
 Check if it’s connected to the wrong terminal or if the input mode is
correct.
 Check if the signal cable connection between video frequency source
and the liquid crystal TV set is correct.
Deterioration of color phase or color
tone
 Check if all the picture setups have been corrected.
Screen position or size is not proper  Check is the screen position and size is correctly set up.
Picture is twisted and deformed  Check to see if the picture-frame ratio is properly set up.
Picture color changed or colorless  Check the “Component” or”RGB”settings of the liquid crystal TV set
and make proper adjustment according to the signal types.
Picture too bright and there is distortion
in the brightest area
 Check if the contrast setting is too high.
 Possibly the output quality of DVD broadcaster is set too high.
 It maybe also due to improper terminal connection of the video
frequency signal in a certain position of the system.
Picture is whitish or too bright in the
darkest area of the picture
 Check if the setting for the brightness is too high
 Possibly the brightness grade of DVD player(broadcaster)is set too
high.
No picture or signal produced from the
displayer if “XXX in search”appears.
 Check if the cable is disconnected.
 Check if it’s connected to the proper terminal or if the input mode is
correct.
There appears an indication - “outside
the receivable scope)
 Check if the TV set can receive input signal. The signal is not
correctly identified and VGAformat is beyond the specified scope.
Remote control cannot work properly  Check if the batteries are installed in the reverse order.
 Check if the battery is effective.
 Check the distance or angle from the monitor.
 Check if there is any obstruct between the remote control and the TV
set.
 Check if the remote control signal- receiving window is exposed to
strong fluorescence.

7
No sound  Check if the “mute” audio frequency setting is selected.
 Check if the sound volume is set to minimum.
 Make sure the earphone is not connected.
 Check if the cable connection is loose.
When playing VHS picture search tape,
there are lines at the top or bottom of
the picture.
 When being played or in pause VHS picture search tape sometimes
can’t provide stable picture, which may lead to incorrect display of the
liquid crystal TVIn this case please press “auto” key on the remote
control so as to enable the liquid crystal TV set to recheck the signal
and then to display correct picture signal
Principle analysis of LC-27K6
For the working principle of LC-27K6 please refer to LC-27K6 block diagram of the complete TV set.
Following is a short description of the signal flow:
RF signal through an integral tuner TUNER201 produces complete color TV signal which is input,
together withAV1/SVHS(SVHS in priority) andAV2 video signals, into U29 VPC3230D for conversion
selection and decoding. Except for being decoded the selected video signal is divided in two routes: one
is fed to AV output terminal and another route of signal to special 21 line decoder U32 Z86229 of
CCD/V-CHIP for decoding. After decoding by U32, the signal is sent back to U29 with R,G,B,FB format
and superimposed to the original picture decoded, then sent to U13 FLI2310 in ITU-R656 of 8B1T
format for progressive line processing.
YPbPr signal, after analog to digital conversion by U30 MST9883 into YUV with 24BIT is also sent
to FLI2310.
Above two routes of signal are processed by FLI2310 for matrix, color density and tint and then
output as RGB with 24 BIT into the main processor chip U12 JAG-ASM. There are other two routes of
signals: one route is RGB signal of VGAfor computer, another route is DV1 into RGB signal with 24 bit to
U12 through interface of U15 TFP403/501. Three routes of signal are processed in U12 for picture
format. Among them, one route of VGA after A/D conversion for RGB is subject to selection for
conversion, together with other two routes, and then processed for digital display including OSD AND
GAMMA correction, and brightness and contrast processing and changed into 1024*768 format. The
RGB signal with 24BIT is output to the LVDS converter, U31 DS90C383A, for conversion into the
signal format which the screen can accept, that is, three pairs of low voltage differential signal and one
pair of time signal. And they are further sent to LCD screen for picture display. The PWM of U12 is also
used to control the brightness of the background light.
The second sound IF signal SIF output from tuner is sent to sound frequency processor N201
MSP3420; the sound frequency signal of YPRPB,and DVI is also sent to N201 after switching over and
selection by switch U34 HEF4052. The AV1/SVHS,AV2 and VGA audio signal are also sent to N201
respectively, where the second sound IF SIF is first demodulated to the audio signal which, together with
four way audio signal, is selected for conversion, and then further sound magnitude controlled and
sound effect treated. The output of left and right signal R/L is divided into two routes: one is sent to SRS
sound field processor N203 M62494 for SRS surrounding sound processing, and further used to drive
the speaker after the D-type sound power amplification N207 LX1722 and amplification of
N205,N206,N208,N210 SI4532DY; the other route is used to drive earphone after power amplification
N212 TLE2142.
Power is supplied from power adapter and then converted into the power required by various
channels and circuits.

U12
SCALER
JAG-ASM
U15 DVI
receiver
TFP403
U13
DEINTER
LACER
FLI2310
RGB
24bit
RGB
24bit
RGB
VGA
DVI
U31
LVDS
DRIVER
DS90C383A
PANEL
RGB
24bit
U19
SDRAM
U20
SDRAM
U14
SDRAM
AV2-V
SVHS-C
AV1-V/S-Y
RF TUNER201
ITU-R656
V
SIF
8bit
U29
VIDEO DECODER
VPC3230
AV-V OUT
U32
CCD
V-CHIP
Z86229
FBV
U30
ADC
MST9883
YPrPb2
U3
EEPROM
U2
MICRO-CONTRLER
TSC80251G2D
U4
FLASHMEMORY
IR/KEYBOARD
SIF
AV1/SVHS-R/L
AV2-R/L
YPrPb2-R/L
DVI-R/L
VGA-R/L
AV-R/L OUT
N201
AUDIO
PROCESSOR
MSP3420
U34
HEF4052
N203
SRS 3D STEREO
CONTROLLER
M62494
N213 N214
AUDIO
AMPLIFIER
MP7720
N212
TLE2142 HEADPHONE
R/L
SPEAKER
LC27K6 BLOCK DIAGRAM
RGB
I C BUS
2
24bit
YUV
R/L
R/L
R/L R/L
YPrPb1-R/L
N2 PI5V330
YPrPb1
8

9
IC BLOCK DIAGRAM
1.MSP3420
Pins description:
2,3 PIN:SCL,SDA applied for control the operation of IC .
27,28 PIN:output left and right sound channel R/L to speaker processor.
36,37 PIN:AV OUT of sound R/L.
47,48 PIN: DVI/YPbPr1/YPbPr2 selected input R/L.
50,51 PIN:Input of VGA. R/L
53,54 PIN:Input of AV2 R/L.
56,57 PIN:Input R/L of AV1/SVHS
67 PIN:Input TV SIF.

10
2.VPC3230
Pins description:
31-34, 37-40 PIN:output format signal of.ITU-R656
70 PIN:Video of AV OUT
71 PIN:Input C of SVHS.
72 PIN:input Video (SVHS in priority) of Y or AV1 of SVHS.
74 PIN:input Video of AV2.
75 PIN:input Video of TV.

11
3.JAG-ASM

12
4.Z86229
Pin description:
7 PIN:Video input
2 PIN:G output
3 PIN:B output
18 PIN:R output
17 PIN:FB output

13
4.Z86229

14
Serial No. of Parts
Part Name Part No. Main components and No. Remark
Sound conversion
board 667-L27K6-15
N201 MSP3420G-Q (353-34200-10)
N203 M62494FP (353-62494-20)
N213
N214 MP7720 (353-77200-10)
Self
produced
CPU board assy’ 667-L27K6-56
U12 JAG-ASM (353-0JAG0-00)
U13 FLI2310 (353-23100-00)
U15 TFP403PZP (353-04030-10)
U29 VPC3230D (353-32300-80)
U30 MST9883B (353-98830-10)
U31 DS90C383A (353-03830-70)
U32 Z8622912SS (353-86229-10)
U2 TSC80251G2D (353-80251-10)
U4 AT49F002NT (352-49002-70)
Self
produced
IR assy’ 667-L27K6-09 Self
produced
KEY board assy’ 667-L27K6-05 Self
produced
VIDEO processing
board 667-L27K6-40 Self
produced
Power supply board 667-L27M6-20 N904 NCP1207 (353-12070-10)
V907 SPP11N60C3 (343-00600-60)
Self
produced
Remote control
RC-U20R 301-UL27K6-20R
Display screen
V270W1-L02 335-27001-00

15
Identification criteria for the bright spot and dark spot of the LCD screen
Q’ty allowed Distance between two spots
Category criteria 15" 20" 22" 30" 40" 15" 20" 22" 30" 40"
One single
spot ≤5 ≤2 ≤5 ≤2 ≤3
2 neighboring
spots ≤2 ≤1 ≤2 ≤1 ≤1
Bright
spot
Total No. ≤5 ≤2 ≤5 ≤2 ≤3
≥15mm
One single
spot ≤6 ≤7 ≤5 ≤4 ≤10
Two
neighboring
spots ≤2 ≤2 ≤2 ≤1 ≤5
Dark
spots
Total No. ≤6 ≤7 ≤5 ≤4 ≤10
≥15mm
≥10mm ≥5mm
Total defected point ≤8 ≤7 ≤5 ≤4 /
Notes:1. Definition of defected point (bright spot, dark spot): It is identified as a defected point if its area
exceeds 1/2 of a single picture element (R,G,B).
2. Definition of bright spot: It is identified as a bright spot if it is bright in the state of dark field and
its bright size remains unchanged
3. Definition of dark spot: It is identified as a dark spot if it is dark in the state of white field and its
dark size remains unchanged
4. Definition of two neighboring points: Defects of a group of picture elements(RB,RG,GB).

EXPLODED VIEW
16

FPE2705
PART LIST OF EXPLDED VIEW
NO. DESCRIPTION PART#
1 AXLETREE COVER BOARD 808-10688-AF0
2 HOLDER ASSY 615-10429-04
3 BACK CABINET COVER BOARD (RIGHT) 808-10689-AF0A
4 INFRARED SENSE ASSY 667-L27K6-09
5 LED COLUMN 700-60265-00
6 POWER BOARD ASSY 667-L27M6-20
7 SOUND SWITCH BOARD ASSY 667-L27K6-15
8 POWER SOCKET BRACKET 870-20955-AF0
9 VIDEO PROCESSING BOARD ASSY 667-L27K6-40
10 DISPLAY SCREEN 335-27001-00
11 SPEAKER ASSY 615-20332-00
12 FRONT CABINET 780-T06W0J0G0
13 PMMA BOARD 808-20296-232A
14 LED SCREEN FIXED BRACKET 615-10481-00
15 CPU BOARD ASSY 667-L27K62-56
16 WALL MOUNT BRACKET 615-10482-00
17 BACK CABINET 780-T06WHJAF1B
18 BACK CABINET COVER BOARD (LEFT) 808-10687-AF0A
16 16

PART LIST
PART# DESCRIPTION LOCA.NO.
SL27K60-01A10 SOFTWARE
100-L27K60-18 FPE2705
100-L27K60-01 LC-27K6
655-B1201-46 (12-PINS) LEAD WITH HOUSING
665-D0002-525
LVDS LINE FERRITE BEAD
655-41201-280 (4-PINS) LEAD WITH HOUSING
655-81201-61 (8-PINS) LEAD WITH HOUSING
655-8E301-33 (8-PINS) LEAD WITH HOUSING
700-60265-00 LED COLUMN
742-30005-09 LINE TIE
789-20039-00 RUBBER PLUG
808-10687-AF0A BACK CABINET COVER BOARD ( GREY 05)
808-10688-AF0 AXLETREE COVER BOARD ( GREY 05)
808-10689-AF0A BACK CABINET COVER BOARD ( GREY 05)
808-20296-00A BOARD
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-23010-14 SCREW SJ2824 ST3X10C-Y
851-23010-14 SCREW SJ2824 ST3X10C-Y
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn
852-54010-84 SCREW SJ2830 M4X10-Y
852-54010-84 SCREW SJ2830 M4X10-Y
852-43006-85 SCREW F(+)M3X6- BLACK
852-43006-85 SCREW F(+)M3X6- BLACK
852-43006-85 SCREW F(+)M3X6- BLACK
852-43006-85 SCREW F(+)M3X6- BLACK
868-20109-00 WASHER
868-20109-00 WASHER
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53012-81 SCREW SJ2830 M3X12-D.Zn
852-53012-81 SCREW SJ2830 M3X12-D.Zn
852-54010-84 SCREW SJ2830 M4X10-Y
852-54010-84 SCREW SJ2830 M4X10-Y
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
852-53006-81 SCREW SJ2830 M3X6-D.Zn
855-A0029-00 SCREW ST4X14
855-A0029-00 SCREW ST4X14
16
18