Audison FORZA AP F1 D User manual

USER’S
MANUAL
rel. 1.0
AP 1 D
audison.com

3
AP F1D
USER’S MAUAL
Index
1. PRECAUTIONS.................................................................................................................................... 10
2. PACKAGING CONTENTS..................................................................................................................45
3. INSTALLATION AND SIZES.............................................................................................................46
4. CABLE SIZE CALCULATION TABLES............................................................................................ 47
5. CONNECTION CABLE........................................................................................................................ 47
6. POWER SUPPLY AND REMOTE CONNECTION / FUSE REPLACEMENT............................. 48
7. PRE IN / SPEAKER IN........................................................................................................................ 49
8. CONTROL PANEL............................................................................................................................... 52
9. INSTALLATION EXAMPLES:........................................................................................................... 53
9.1 3 WAY ACTIVE FRONT + REAR + SUB WITH AP F1D ..........................................................54
9.2 FRONT + REAR + SUB WITH AP F1D ...................................................................................... 56
9.3 FRONT+REAR+ SUB WITH AUDISON BIT PROCESSOR.....................................................58
10.TECHNICAL SPECIFICATIONS ....................................................................................................... 59

11
AP F1D
USER’S MAUAL
Before installing the components, please carefully read all of the instructions contained in this manual. It is advisable to carefully follow the highlighted
instructions. Failure to respect these instructions may cause unintentional harm or damage to the components.
SAFETY CONSIDERATIONS
1. Makesureyourcarhasa12voltDCnegativegroundelectricalsystem.
2. Donotinstallcomponentsinsidetheenginecompartmentorexposethemtowater,excessivehumidity,dustordirt.
3. Neverruncablesoutsidethevehicleorinstalltheampliernexttomechanicalorelectronicdevices.
4. OperatetheAPF1Donlywheninternaltemperatureisbetween0°C(32°F)and55°C(131°F).TheAPF1Dmusthaveaminimum3cm(1.5”)distancefrom
 anystructure.Theremustbegoodaircirculationaroundthechassis.
5. Makesurethelocationyouchoseforthecomponentdoesnotaffectthecorrectfunctioningofthevehicle’smechanicalandelectricaldevices.
6. Makesurethepowercabledoesnotshortcircuitduringinstallationandconnection.
7. Useextremecautionwhencuttingordrillingthecarchassis,checkingthatthereisnoelectricalwiringorstructuralelementsunderneath.
8. Userubbergrommetstoprotectthewirewhenrunningthroughholesinmetalandusepropermaterialsifclosetoheat-generatingdevices.
9. Makesureallthecablesareproperlysecuredalongtheirentirelength.Also,makesuretheirouterprotectivejacketisflameresistantandselfextinguishing.
 Securetheconnectedcablesclosetotheterminalblockswithwiretiesorclamps.
10.Pre-planthecongurationofyournewAPF1Dandthebestwiringroutestoeaseinstallation.Usehighqualitycables,connectorsandaccessories,as
 youwillndintheAudisoncatalogue.
HOW TO CONNECT THE AP F1D
ThefollowinggraphicsrepresentthemainstepsfortheAPF1Dconnections.Itsuniversalityandversatilityofferendlesspossibilitiesandcongurations.
Specicstepsordifferentproceduresmayberequiredinsomeapplications.Ifyouhaveanyquestionsaboutcongurationorfunction,pleaserefertothe
AdvancedManualthatyoucanndintheCDinsidethegiftboxorcontactyourAudisondealerorAudisonauthorizedservicecenterforassistance.Forits
operationandforanyotherneed,pleaserefertothefollowingpagesofthismanual
1. BeforeinstallingtheAPF1D,turnoffthesourceandallotherelectronicdevicesintheaudiosystemtopreventanypossibledamage.
2. Runaspecicallydesignedpowercablewithproperdiameter(8AWG,Ø3.2mm/0.128’)fromtheAPF1Dbattery.
3. Connectthepowercablesobservingcorrectpolarity.Connectthe(-)terminaltothecarchassisrst,thenconnectthe(+)terminaltothecablecoming
 fromthebattery.Tocorrectlygroundtheproduct(-GROUND)useaxingpointinthevehiclechassis;removeallpaintorgreasefromthemetalif
 necessary,checkingwithavoltmeterthatthereiscontinuitybetweenthebatterynegativeterminal(-)andthechosenxingpoint.Thepowerconnector
 acceptsan8AWG(Ø3.2mm/0.128’)15mm/0.6’peel-offcable.Ifpossible,connectallcomponentstothesamegroundpoint;thissolutionrejects
 mostundesirednoisewhichcanbegeneratedduringtheaudioreproduction.
4. Putaninsulatedfuseholdermaximum20cmfarfromthebatterypositiveterminal;connectoneendofthepowercabletoitafterconnectingitsother
 endtotheamplier.
5. TURNON:theAPF1Dcanbeturnedonthrough:
-RemoteIn,byconnectingtheterminaltotheRemOutofanAfterMarketheadunitorfromtherelaunchwiringofanamplierfromthePrimaAPF8.9bit/
  AP8.9bit/AP4.9bitline.
 Thelogoonthetopsideoftheheatsinklightsblue,indicatingthattheproductison.AflashingoftheREDlogoeverysecondindicatestheactivationof
 thethermalprotection2flashesoftheREDlogoeverysecondindicatean“OVERLOAD”/Faultinthewiringofthespeakers,4flashesoftheREDlogo
 everysecondindicatetheactivationofthe“OVERVOLTAGE”protectioncausedbyabatteryvoltagehigherthan16V,theREDlogoturningonindicatesan
 internalfailureoftheproduct,pleasecontacttheauthorizedcustomerservicecenter.
6. SPKIN:HILEVELmonophonicanaloginput.UsethemultipointconnectorprovidedtoconnecttoanampliedsourceoranamplierfromthePrimalineAP4.9bit.
 Thesignaltobeappliedmusthavealevelbetween2and20VRMS.TheinputsensitivityoftheAPF1Discontrolledbythe“SENSITIVITY”3-position
 switch:2V-6.5V-20V.
7. PREIN:Lowlevelmonophonicanaloginput.UseanRCAconnectortoconnecttoanaudiosourceortoanamplierfromthe“PrimaAPF8.9bit/AP8.9bit/
 AP4.9bit”linefeaturingthisconnection.Thesignaltobeappliedmusthavealevelbetween0.6and6VRMS.TheinputsensitivityoftheAPF1Dis
 controlledbythe“SENSITIVITY”3-positionswitch:0.6V-2V-6V.
8. SPEAKEROUT:powerterminal+and-ofthemonophonicoutput.Theavailablepowerattheoutputis500Wx1@4ohm,800Wx1@2ohmand1000Wx1@1ohm.
9. FUSE:toreplacethefuse,removeitfromitsholderlocatednearthepowersupplyterminalblockandreplaceitwithanotherfuseofequalvalue.
10.INSTALLATION:Allcomponentsmustbesolidlyxedtothevehiclestructure.Dothesamewheninstallinganyadditionalcustomstructuresyoumay
 havebuilt.Makesurethatyourinstallationissolidandsafe.Acomponentcomingloosewhiledrivingmaycauseseriousdamagetothepassengers,as
 wellastoothervehicles.Whentheinstallationiscomplete,checkthesystemwiringandverifyallconnectionswereperformedcorrectly.
11.ForacorrectuseoftheAPF1D,itisessentialtoconsultthismanualinitsentirety.
12. WarrantyCerticate:pleasecheckouttheAudisonwebsiteforfurtherinformation.
SAFE SOUND
USECOMMONSENSEANDPRACTICESAFESOUND.PLEASEREMEMBERTHATLONGEXPOSURETOEXCESSIVELYHIGHSOUNDPRESSURELEVELS
MAYDAMAGEYOURHEARING.SAFETYMUSTBEATTHEFOREFRONTWHILEDRIVING.
1PRECAUTIONS English
Information on electrical and electronic equipment waste (for those European countries which organize the separate collection of waste)
ProductswhicharemarkedwithawheeledbinwithanXthroughitcannotbedisposedoftogetherwithordinarydomesticwaste.Theseelectricalandelectronicproductsmustberecycledin
properfacilities,capableofmanagingthedisposaloftheseproductsandcomponents.Inordertoknowwhereandhowtodelivertheseproductstothenearestrecycling/disposalsiteplease
contactyourlocalmunicipalofce.Recyclinganddisposingofwasteinaproperwaycontributestotheprotectionoftheenvironmentandtopreventharmfuleffectsonhealth.
1

44
AP F1D
USER’S MAUAL 1
              
              
  
         
    
    
               
            
                 
              
              
       
TheAudisonproductsarewarranted,undernormalfunctioningconditions,fortheperiodoftimeassetbythelawsinforce,againstdefectsconcerning
materialsortheirmanufacturing.Thewarrantyisvalidfromthedateofpurchase,certiedbyreceipt.
Thewarrantyisnotvalidif:
•theproductisdamagedbyincidents,installationsand/orimproperuse,orby anyothercausesnotdependingonmaterialsormanufacturingdefects;
• theproductismodiedortamperedwithbyunauthorisedpeople;
•itsserialnumberhasbeenalteredorcancelled.
Whiletheproductisunderwarranty,defectivepartswillberepairedorreplacedatthemanufacturer’sdiscretion.
Thedefectiveproduct,alongwithnoticationaboutit,mustbereturnedtothedealerfromwhichitwaspurchasedtogetherwiththewarrantycerticateduly
lledin.Iftheproductisnolongerunderwarranty,itwillberepairedatthecurrentcosts.
Elettromedias.r.l.doesnotundertakeanyliabilityfordamagesduetotransportation.
Elettromedias.r.l.doesnottakeanyresponsibilityfor:costsorlossofprotduetotheimpossibilitytousetheproduct,otheraccidentalorconsequentialcosts,
expensesordamagessufferedbythecustomer.
Warrantyaccordingtolawsinforce.
FormoreinformationvisittheAudisonwebsite.
Audison Warranty

45
AP F1D
USER’S MAUAL
2PACKAGING CONTENT
- Multipolarcable,Inputs/Rem:
- MultipolarcableSpeakersout:
-NR. 2 -30Areplacementfuse:
- 2.5mmhexkey:
-NR. 4 -4.2x50mm(0.16”x2”)self-tapping,crossheadmountingscrews:
-AP F1D amplifier
- User’sManual
30 A
30 A
FUSE 2x30A
1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
SPKIN -
REMIN
MUTE
SPKIN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
2

46
AP F1D
USER’S MAUAL
FUSE 2x30A
1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
SPK IN -
REM IN
MUTE
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
External Size
155 mm / 6.1 in
.
238 mm / 9.37 in .
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
Mounting Size How to mount
216 mm / 8.5 in.
133 mm / 5.2 in.
49,5 mm / 1.95 in.
3INSTALLATION AND SIZE
3
AP F1D
AP F1D

47
AP F1D
USER’S MAUAL
4CABLE SIZE CALCULATION TABLES
5CONNECTION CABLE
Connection length
Applied power
Cable diameter
200 mm / 7.87 in.
200 mm / 7.87 in.
10 mm / 0.39 in.
10 mm / 0.39 in.
FRONT VIEW
FRONT VIEW
Blue REM IN Orange SPK IN+
Blue/White MUTE Orange/Black SPK IN-
White OUT 2+ White OUT 1+
White/Black OUT 2- White/Black OUT 1-
FRONT VIEW
Blue/White MUTE Blue REM IN
Orange/Black SPK IN- Orange SPK IN+
Speaker out cable
Input cable
*Current Draw I (A)
Cable Length (m)
4/5

48
AP F1D
USER’S MAUAL
SD
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
(Not provided.
Suggested Fuse
30 A delayed)
Max 20 cm / 7.9 in.
15 mm / 0.6 in.
8 AWG Max
1 2
SPEAKER
OUT
ON
FUSE 2x30A
POWER - 12V
MUTE onlytoAP4.9bit
REM IN
blue
blue/white
REM OUTREM OUT
FUSE
REPLACEMENT
WARNING:
Firmlypress
contactsofeachfuse
introtheir
fuse-holderclips
2 x 30A
BLADE
FUSE
AP F8.9 bit
SOURCE
6POWER SUPPLY AND REMOTE CONNECTION / FUSE REPLACEMENT
6
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
BATTERY
12 V FUSED HOLDER
GND GND
GND
AMP 1 AMP 2
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
FUSE 2x30A 1 2
SPEAKER
OUT
POWER - 12V
BATTERY
12 V
GND
GND
AMP 1 AMP 2
WARNING
MULTIPLE POWER SUPPLY CONNECTION
HEX KEY 2,5mm/0.1in.

49
AP F1D
USER’S MAUAL
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
SD
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
SD
X
SOURCE
SOURCE
APL2-LINKCABLE
(optional)REM OUT
REM IN
SPK IN + SPK IN -
PRE IN
PRE
OUT
SPK OUT
APL2-LINKCABLE
(optional)
AP F1D with REM IN
AP F1D without REM IN
AP F1D
AP F1D
7
7PRE IN / SPEAKER IN

50
AP F1D
USER’S MAUAL
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
SD
SUB PRE OUT
AP8.9bit/AP4.9bit
SOURCE
SUB PRE
OUT
AP F1D + AP8.9 bit / 4.9 bit PRE OUT
AP F1D + HEAD UNIT PRE OUT
AP F1D
AP F1D
7

51
AP F1D
USER’S MAUAL
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
PHONE
REM
IN
REM
OUT
12V
KEY
SW
INPUTS
MUTEIN FL FR RRRL
ADLink
ACLink
X
SUB OUT
AudisonProcessor
AP F1D + AUDISON PROCESSOR PRE OUT AP F1D
7

52
AP F1D
USER’S MAUAL
AP F1D
8
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
INPUT SENSITIVITY
HI MID LO
HI LEVEL INPUT
SENSITIVITY
HI:2VRMS
MID:6.5VRMS
LO:20VRMS
PRE INPUT
SENSITIVITY
HI:0.6VRMS
MID:2VRMS
LO:6VRMS
POWER ON
LEDBLUE
LEDRED
< 2 Ohm CHECK
Flash-LED RED
70 °C
Flash-LED RED
8CONTROL PANEL
> 16 Volt CHECK
Flash-LED RED
SPEAKER OUTPUT
POWER@4ΩW(RMS) POWER@2ΩW(RMS) POWER@1ΩW(RMS)
500 x 1 800 x 1 1000 x 1
20 200 500 2k 20k Hz
LO-PASSAMP OUTPUT

53
AP F1D
USER’S MAUAL
9INSTALLATION EXAMPLES
9
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
FUSE 2x30A 1 2
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
H M L
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
SUBWOOFER
1Ωmin.
2Ωmin. 2Ωmin.
+
+-
-
-+
SUBWOOFER
from
source/amplier/processor
from
source/amplier/processor
AP F1D with 1 SUBWOOFER
AP F1D with 2 SUBWOOFER
AP F1D
AP F1D

54
AP F1D
USER’S MAUAL
9.1 3 WAY ACTIVE FRONT + REAR + SUB WITH AP F1D
FUSE 2x30A 12
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
HML
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
01
2
3
4
5
6
7
USB
PRESETS OPTICAL IN
SUB OUTFUSE 2x30A CTRL SPEAKER IN PRE IN
DRC
UPGRADE
OFF ON
SPEAKER OUT
POWER - 12V
12367845
Out 1 (+) Out 8 (+) Out 3 (+) Out 6 (+) Out 5 (+) Out 4 (+) Out 7 (+) Out 2 (+) Out 1 (-) Out 8 (-) Out 3 (-) Out 6 (-) Out 5 (-) Out 4 (-) Out 7 (-) Out 2 (-)
SUBWOOFER
REAR
LEFT
WF
LEFT
FRONT
MD
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
AP F8.9 bit
AP F1D
MD
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
RIGHT
1
2
3
4
5
6
70
9

55
AP F1D
USER’S MAUAL
OUTPUT CONFIGURATION:
= RMS power at suggested loads: 1480 W
AP TYPE OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT*POWER 4ΩPOWER 2Ω
AP F8.9 bit
(not supplied)
OUT 1 FRONT TW LEFT HI PASS Linkwitz 3000 Hz @12 dB 82,2 cm 85 W 13 0 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 3000 Hz @12 dB 116,2 cm 85 W 130 W
OUT 3 FRONT MD LEFT BAND PASS Linkwitz 500 Hz @12 dB
3000 HZ @ 12 dB 82,2 cm 85 W 13 0 W
OUT 4 FRONT MD RIGHT BAND PASS Linkwitz 500 Hz @12 dB
3000 HZ @ 12 dB 116,2 cm 85 W 130 W
OUT 5 FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB
500 HZ @ 12 dB 82,2 cm 85 W 130 W
OUT 6 FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB
500 HZ @ 12 dB 116,2 cm 85 W 130 W
OUT 7 REAR LEFT HI PASS Linkwitz 80 Hz @12 dB 62,3 cm 85 W 13 0 W
OUT 8 REAR RIGHT HI PASS Linkwitz 80 Hz @12 dB 116,2 cm 85 W 13 0 W
AP F1D SPK OUT SUBWOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm 500 W 800 W
Note
9

56
AP F1D
USER’S MAUAL
FUSE 2x30A 12
PRE IN
SPEAKER
OUT
POWER - 12V
SENSITIVITY
HML
REM IN
MUTE
SPK IN -
SPK IN +
ART
ON OFF
SPK-IN
MODE
USS
OFF
USS
ON
01
2
3
4
5
6
7
USB
PRESETS OPTICAL IN
SUB OUTFUSE 2x30A CTRL SPEAKER IN PRE IN
DRC
UPGRADE
OFF ON
SPEAKER OUT
POWER - 12V
123 67845
9.2 FRONT + REAR + SUB WITH AP F1D
1
2
3
4
5
6
70
9
Out 8 (+) Out 1 (+) Out 5 (+) Out 3 (+) Out 2 (+) Out 7 (+) Out 8 (-) Out 1 (-) Out 6 (-) Out 4 (-) Out 2 (-) Out 7 (-)
SUBWOOFER
REAR
LEFT
WF
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
RIGHT

57
AP F1D
USER’S MAUAL
OUTPUT CONFIGURATION:
9
Note
= RMS power at suggested loads: 1660 W
AP TYPE OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT*POWER 4ΩPOWER 2Ω
AP F8.9 bit
(not supplied)
OUT 1 FRONT TW LEFT HI PASS Linkwitz 3000 Hz @12 dB 82,2 cm 85 W 130 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 3000 Hz @12 dB 116,2 cm 85 W 130 W
OUT 3+ / 4- FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB
3000 HZ @ 12 dB 82,2 cm 260 W -
OUT 5+ / 6- FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB
3000 HZ @ 12 dB 116,2 cm 260 W -
OUT 7 REAR LEFT BAND PASS Linkwitz 80 Hz @12 dB 62,3 cm 85 W 130 W
OUT 8 REAR RIGHT BAND PASS Linkwitz 80 Hz @12 dB 116,2 cm 85 W 130 W
AP F1D SPK OUT SUBWOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm 500 W 800 W

58
AP F1D
USER’S MAUAL
PHONE
REM
IN
REM
OUT
12V
KEY
SW
INPUTS
MUTEIN FLFR RRRL
ADLink
ACLink
AP F1D AP F1D
AP F1D AP F1D
AP F1D
9.3 FRONT+REAR+ SUB WITH AUDISON BIT PROCESSOR
SUBWOOFER
REAR
LEFT
FRONT
LEFT
REAR
RIGHT
FRONT
RIGHT
9
SENSITIVITY
HM L

59
AP F1D
USER’S MAUAL 10
10 TECHNICAL SPECIFICATION
POWER SUPPLY
Power supply voltage / fuse: 11÷15VDC/2x30A
Operating power supply voltage 6.5 ÷ 17 VDC
Idling current: 1.3 A
Idling current when off 0.05mA
Consumption@14.4VDC,1Ω,MaxMusicalPower: 50 A
Remote IN 6.5 ÷15VDC(1mA)
ART - Automatic Remote Turn on/off from OUTPUT BTL speakers (Selectable) 2 ÷ 7 VDC
AMPLIFIER STAGE
Distortion-THD@100Hz,4Ω,70%RatedPower: 0.1 %
Dampingfactor@100Hz,4Ω,2VRMS: 140
Bandwidth @ -3 dB: 10Hz÷500Hz
S/N ratio (A weighted @ 1 V Input): 110dBA
Input sensitivity PRE IN:
Input sensitivity SPEAKER IN:
Selectable:0.6-2.0-6.0VRMS
Selectable:2.0-6.5-20VRMS
Minimum load impedance 1Ω
Outputpower(RMS)@14.4VDC,1%THD:
• 1 Ch @ 4Ω 500Wx1
• 1 Ch @ 2Ω 800 Wx1
• 1 Ch @ 1Ω 1000 Wx1
CEA SPECIFICATION
Outputpower@4Ω,1%THD+N,14.4V 500 W
SN ratio (ref. 1 W output) 81,5dB
INPUTS
Pre-In Inputs RCA
Speaker-In Inputs wired
Mute (Energy Saving control) wired(activetogroung)
OTHER
Ambient operating temperature range 0°Cto55°C(32°Fto131°F)
SIZE
Max Size W x H x D (mm/inch) 238x49,5x155/9.37x1.95x6.1
Weight (kg/lbs) 1,92/4.23

PART OF ELETTROMEDIA
62018PotenzaPicena(MC)Italy
T+390733870870-F+390733870880
www.elettromedia.it
Tuttelespecicheriportatesonosoggetteacambiamentosenzapreavviso Allspecicationssubjecttochangewithoutnotice
10125041_20.REV.B
audison.com