Audison prima AP8.9 bit User manual

rev. 1.0 C
USER’S
MANUAL
AP8.9

AP8.9 bit /
2
USER’S MANUAL
Index
1. PRODUCT DESCRIPTION / PRECAUTIONS.......................................................................................................................... 3
2. PACKAGE CONTENTS ...............................................................................................................................................................3
3. AP8.9 bit and DRC INSTALLATION........................................................................................................................................4
4. CONNECTION PANEL DESCRIPTION..................................................................................................................................... 5
1 POWER ..............................................................................................................................................................................5
2INPUTS / REM IN-OUT...................................................................................................................................................6
3 ASP AUTOMATIC SPEAKER PRESENCE ....................................................................................................................7
4 SPEAKER OUT..................................................................................................................................................................8
5 SUB OUT ...........................................................................................................................................................................8
6 OPTICAL IN.......................................................................................................................................................................8
7 DRC ................................................................................................................................................................................8
8 USB ................................................................................................................................................................................8
9 UPGRADE OFF-ON..........................................................................................................................................................8
10 PRESET .............................................................................................................................................................................9
11 FUSE ................................................................................................................................................................................9
12 LOGO STATUS .................................................................................................................................................................9
5. CONNECTIONS .........................................................................................................................................................................10
5.1 POWER SUPPLY AND REMOTE TURN ON. .............................................................................................................10
5.2 INPUT SIGNALS ............................................................................................................................................................10
5.3 DIGITAL OPTICAL IN INPUT SIGNALS .....................................................................................................................12
5.4 OUTPUT SIGNALS ........................................................................................................................................................13
5.4.1 PRESET 0 DEFAULT: 3 WAY ACTIVE FRONT + REAR ...............................................................................14
5.4.2 PRESET 1: 2 WAY ACTIVE FRONT + 2 PASSIVE REAR + SUBWOOFER ................................................15
5.4.3 PRESET 2: 3 WAY ACTIVE FRONT + SUBWOOFER....................................................................................16
5.4.4 PRESET 3: FRONT + REAR + SUBWOOFER.................................................................................................17
5.4.5 PRESET 4: 2 WAY ACTIVE FRONT + REAR + SUBWOOFER.....................................................................18
5.4.6 PRESET 5: 3 WAY ACTIVE FRONT + REAR + EXTERNAL AMPLIFIED SUB...........................................19
5.4.7 PRESET 6: 2 WAY ACTIVE FRONT + REAR + EXTERNAL AMPLIFIED SUB...........................................20
5.4.8 PRESET 7: 2 WAY ACTIVE FRONT + REAR + 2 WAY CENTER CHANNEL + EXTERNAL AMPLIFIED SUB...21
5.5 PERSONAL COMPUTER AND DIGITAL REMOTE CONTROL (DRC)....................................................................22
6. GUIDE FOR INSTALLING/UNINSTALLING PRIMA SOFTWARE AND DRIVERS..........................................................23
6.1 GUIDED PROCEDURE FOR PC SOFTWARE INSTALLATION................................................................................23
6.2 GUIDED PROCEDURE FOR DRIVER INSTALLATION .............................................................................................25
6.3 UNINSTALLING AP8.9 bit SOFTWARE ....................................................................................................................26
7. HOW TO SET UP AP 8.9 BIT WITH A PC............................................................................................................................27
7.1 OFFLINE MODE..............................................................................................................................................................27
7.2 TARGET MODE ..............................................................................................................................................................28
7.3 ADJUSTING ACOUSTIC REPRODUCTION ...............................................................................................................34
7.3.1 DEVICE INFO ......................................................................................................................................................34
7.3.2 FILE MAIN MENU ..............................................................................................................................................35
7.3.3 MEMORIES MAIN MENU .................................................................................................................................35
7.3.4 SETTINGS MAIN MENU...................................................................................................................................36
7.3.5 DEVICE MAIN MENU ........................................................................................................................................39
7.3.6 HELP MAIN MENU............................................................................................................................................40
7.3.7 SELECTED INPUT .............................................................................................................................................40
7.3.8 CHANNEL MAP..................................................................................................................................................40
7.3.9 SELECT CHANNEL............................................................................................................................................41
7.3.10 FILTER SETTINGS .............................................................................................................................................41
7.3.11 SET DISTANCE AND DELAY............................................................................................................................43
7.3.12 PARAMETRIC EQUALIZER...............................................................................................................................46
7.3.13 OUTPUT LEVEL .................................................................................................................................................47
7.3.14 MEMORY.............................................................................................................................................................47
7.3.15 STATUS BAR ......................................................................................................................................................47
8. TROUBLESHOOTING ...............................................................................................................................................................48
8.1 SYNCHRONIZATION WITH A PC................................................................................................................................48
8.2 BACKGROUND NOISE ..................................................................................................................................................48
8.3 FIRMWARE UPGRADE..................................................................................................................................................49
9. DRC - DIGITAL REMOTE CONTROL (OPTIONAL) .............................................................................................................51
9.1 SEL BUTTON FUNCTIONS ..........................................................................................................................................52
9.2 OPERATIONAL ERROR MESSAGES...........................................................................................................................52
10. ACCESSORIES...........................................................................................................................................................................53
10.1 ASP - AUTOMATIC SPEAKER PRESENCE................................................................................................................53
10.2 ACP 2 - 2 RCA ADAPTER CABLE................................................................................................................................53
10.3 ACP 6 - 6 RCA ADAPTER CABLE................................................................................................................................53
10.4 APK 3 - AUDISON PRIMA TOWER KIT 3...................................................................................................................53
10.5 DRC DIGITAL REMOTE CONTROL.............................................................................................................................54
10.6 ECK DRC - CABLE EXTENSION KIT...........................................................................................................................54
10.7 OP 1.5 TOSLINK OPTICAL CABLE 1.5 m / 59.05 in................................................................................................54
10.8 OP 4.5 TOSLINK OPTICAL CABLE 4.5 m / 177.16 in .............................................................................................54
10.9 STA - F/F SOCKET TOSLINK ADAPTER....................................................................................................................54
10.10 SFC BENCH TEST DEVICE...........................................................................................................................................55
11. TECHNICAL SPECIFICATIONS ..............................................................................................................................................56

3
AP8.9 bit /
USER’S MANUAL
1.PRODUCT DESCRIPTION / PRECAUTIONS
2. PACKAGE CONTENTS
AP8.9 bit is a 9 channel amplifier with 8 channels amplified and settable in bridge mode; it also features a 32 bit,
147 MHz clock speed, 24 bit AD/DA converter digital sound processor (DSP), essential to maximize the acoustic
performance of your car audio system.
It can be interfaced with any factory system, even on cars with built-in audio processors, since with the
de-equalization function, AP8.9 bit will send back a linear signal.
It features 7 signal inputs, 6 Hi-Level and 1 S/PDIF optical digital and provides 8 amplified power outputs and
1 pre-amplified that is optimized for driving a subwoofer.
Each output channel has available: graphically adjustable parametric equalizers, 68-frequency steps electronic
crossover and BUTTERWORTH or LINKWITZ filters with 6-24 dB slopes and a digital time delay line.
The user can make adjustments that allow him or her to interact with AP8.9 bit through the DRC remote control device.
WARNING: 1.a PC provided with Windows XP, Windows Vista, Windows 7 or Windows 8 operating system, 1.5 GHz minimum
processor speed, 1 GB RAM minimum memory and a 1024 x 600 pixels minimum resolution graphics card as
well as at least 512 MB of available hard-disk space are required to install the software and setup the product.
2.Before connecting the product, carefully read this manual. Improper connections may cause damage
to AP8.9 bit or to the speakers in your car audio system.
-Multipolar cable, Inputs/Rem:
-Multipolar cable Speakers out:
-1 - 30A replacement fuse:
-1.8 m USB cable:
-2.5 mm hex key:
-4 4.2 x 50 mm self-tapping, cross head mounting screws:
-AP8.9 bit amplifier
-Warranty
-Quick start guide
-CD ROM containing:
AP8.9 bit Software
This owner’s manual (.pdf)
Audio Test Tracks
QUICK
START
GUIDE
AP8.9
1
30 A
CD 1.0A

AP8.9 bit /
4
USER’S MANUAL
3. AP8.9 bit AND DRC INSTALLATION
External Size
Mounting Size How to mount
DRC (optional)
Installation
Important: Do not use
aggressive cleaning agents
or abrasive cloths to clean
the display. Simply use a soft
cotton cloth that has been
lightly dampened with water.
134 mm / 5.2 7 in.
198 mm / 7.8 in.
114 mm / 4.5 in.
178 mm / 7 in.
45.50 mm / 1.8 in.
68 mm / 2.68”
90 mm / 3.54”90 mm / 3.54”
35 mm / 1.38”35 mm / 1.38” Ø 2 mm / 1/8”
50 mm / 2”
16 mm / 0.63”
17 mm / 0.67”
12.5 mm / 0.49”12.5 mm / 0.49”
43.5 mm / 1.71”
13.5 mm / 0.53”
3.5 mm / 0.14”
6 mm / 0.23”6 mm / 0.23”
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
1 2 3 4 5 1 2 3 4 5 6 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
3

5
AP8.9 bit /
USER’S MANUAL
4. CONNECTION PANELS - DESCRIPTION
POWER.
+Power (11-15 VDC): connection terminal for AP8.9 bit power supply positive pole. The jack accepts a stripped
cable up to 15mm/0.6" with maximum section of 8 AWG (∅3,2mm / 0.12”). For better power transfer we
recommend using cables with the largest possible cross-section and with the same cross-section as the cable
connected to the negative pole.
- Power (Ground): connection terminal for the negative power supply pole of the amplifier. Connect here the negative
battery cable or a cable connected to the vehicle chassis. The opening will take a stripped cable up to 15mm/0.6"
with a maximum section of 8 AWG (∅3,2mm / 0.12”). For better power transfer, we recommend using cables with
the largest possible section and with the same section as the cable connected to the positive pole.
In order to correctly connect the ground (-), use a screw that is already present on the metal part of the vehicle; If
necessary, remove any paint residue or grease, using a tester to make sure there is continuity between the negative
terminal (-) on the battery and the mounting point. If possible, connect all of the grounds on the audio components
to the same grounding point. This helps reduce most of the interference than can occur in audio reproduction.
WARNING: Make sure the connection polarity is as indicated on the terminals. A misconnection may result in damage to the
AP8.9 bit. After applying power, wait at least 10 seconds before turning the AP8.9 bit on.
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
1 2 3 4 5 1 2 3 4 5 6 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
1 24 5
6 789
11 10
3
12
4
1

AP8.9 bit /
6
USER’S MANUAL
INPUTS / REM IN-OUT.
AP8.9 bit comes with a 16 pole multipolar connector to manage the input signals, REM IN/REM OUT connections and
the control functions for the auxiliary inputs.
1. INPUTS FL FR RL RR: MASTER inputs connect here the amplified signal wires coming from the main analog
source. Input sensitivity automatically adjustable from 2 to 15 V RMS (see sec. 7.2.5).
Channels FL FR RL RR feature the AUTO TURN ON (ART) function through connection with the outputs on the source
speakers. This function can be excluded using the PC Software.
Remark: The ACP6 / ACP2 accessory can also be used to interface head units equipped with PRE OUT output (min. 2V)
to the AP8.9 bit inputs. (see sec. 10.2 - 10.3)
2. INPUTS IN1 IN2: Auxiliary signal inputs that can be used when configuring the unit to reconstruct a multi-amplified
signal (Front Tweeter, Front Mid Hi, Center, Sub) or specialized like AUX inputs (see sec. 7.2.5).
3. REMOTE:
- REM IN. Input to turn on AP8.9 bit remotely through the audio signal source Remote Out. REM IN can be connected
to the ignition switch terminal (ACC). The voltage must be between 7 and 14.5 VDC. If using a source with a amplified
outputs, AP8.9 bit can be automatically turned on (see sec. 7.3.4.7), so it will not be necessary to connect the REM IN
terminal.
- REM OUT. Output to turn on other devices/amplifiers connected after AP8.9 bit.
From the time it is turned on, it takes 1 second to supply the signal to the REM OUT output, but it will be possible
to set this delay via software (see sec. 7.3.4.7).
The 200 mA output current capability can also drive an automotive relay.
4. SWITCH INPUTS:
- OPTICAL SELECT: It allows the input selection OPTICAL IN / AUX IN. This control is active bringing the
terminal to +12V and the input choice to be activated can be programmed using the PC software (see sec. 7.3.4.7), the
unit can also be turned on using this terminal.
- MASTER ENABLE: It enables the MASTER input selection. This control is active bringing the terminal to +12V.
16: white FL+
8: white/black FL-
15: gray FR+
7: gray/black FR-
14: green RL+
6: green/black RL-
13: violet RR+
5: violet/black RR-
12: cyan IN1+
4: cyan/black IN1-
11: orange IN2+
3: orange/black IN2-
9: blue REM IN
1: blue/white REM OUT
10: pink OPTICAL SELECT
2: brown MASTER ENABLE
1
2
3
4
200 mm / 7.87 in. 10 mm / 0.39 in.
FRONT VIEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
2

7
AP8.9 bit /
USER’S MANUAL
ASP AUTOMATIC SPEAKER PRESENCE
Input for ASP module if using signals coming from OEM sources. This module simulates the load of the OEM
factory system speakers, allowing proper interface allowing proper interfacing between the source amplified
outputs and the AP8.9 bit analog inputs. (see sec. 7.3.4)
The ASP module is optional and is required only in some cases when installing with factory OEM sources.
WARNING: If interfacing AP8.9 bit with sources equipped with PRE OUT outputs, this module must not be used.
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
1 2 3 4 5 1 2 3 4 5 6 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
4
ASP OK
ASP NO
3

AP8.9 bit /
8
USER’S MANUAL
SPEAKER OUT.
AP8.9 bit comes with a 16 pole multipolar connector to manage the power output signals.
A minimum of 4 and a maximum of 8 speakers can be configured based on the system you wish to create in your
vehicle. (see sec. 5.4)
SUB OUT.
Pre-amplified output subject to LO PASS filtering optimized to drive a mono amplifier for an external subwoofer or
active subwoofer. (see sec. 5.4)
OPTICAL IN.
AP8.9 bit accepts at its input PCM signals up to 96 kHz / 24 bit sampling frequency rate. So DOLBY DIGITAL (AC3)
multi-channel signals coming from audio/video sources (such as the audio of a film in DVD) or DTS can not be
reproduced. Connect a fiber optic cable with a TOSLINK connector. This input can be selected using the
external DRC control or by activating it using the OPTICAL IN terminal. (see sec. 5.2)
DRC.
Connection terminal for remote control of the functions (OPTIONAL) on AP8.9 bit. (see sec. 5.5 - sec. 9)
USB.
USB (micro) connection to connect the product to a PC in order to manage the functions using AP8.9 bit software.
The connection is USB 1.1/2.0/3.0 compatible.
UPGRADE OFF-ON.
Switch ON allows the product to be updated in BOOT LOADER mode. (see sec. 8.3)
1: white/black OUT 8-
9: white OUT 8+
2: white/black OUT 7-
10: white OUT 7+
3: white/black OUT 6-
11: white OUT 6+
4: white/black OUT 5-
12: white OUT 5+
5: white/black OUT 4-
13: white OUT 4+
6: white/black OUT 3-
14: white OUT 3+
7: white/black OUT 2-
15: white OUT 2+
8: white/black OUT 1-
16: white OUT 1+
200 mm / 7.87 in. 10 mm / 0.39 in.
FRONT VIEW
OUT 8- 1
OUT 7- 2
OUT 6- 3
OUT 5- 4
OUT 4- 5
OUT 3- 6
OUT 2- 7
OUT 1- 8
9 OUT 8+
10 OUT 7+
11 OUT 6+
12 OUT 5+
13 OUT 4+
14 OUT 3+
15 OUT 2+
16 OUT 1+
4
4
5
6
7
8
9

9
AP8.9 bit /
USER’S MANUAL
PRESET.
AP8.9 bit has 8 setups preloaded in its memory, one being editable. They allow the product to be
used without the need to connect it to a PC. (see sec. 5.4.1; 5.4.8)
The preset choice is based on the factory system in the car or the type of system you wish to create.
FUSE.
30 A blade protection fuse needs to be replaced, use same type and value as the original.
LOGO STATUS.
AP8.9 bit has an built-in control that manages its status and protects the circuits and connections to the
speakers. The logo on the AP8.9 bit top cover will change its status in case of any possible product malfunctions.
A BLUE logo means:
AP8.9 bit is on.
A flashing RED/BLUE logo means:
The “UPGRADE MODE” switch on the product is set to “ON” position, or the product Firmware is being updated.
A flashing BLUE logo means:
The unit is in stand-by (energy saver) because there is no audio signal. This function (AST) can be activated using the PC
software.
(see sec. 7.3.4.7) and the stand-by time ranges from a minimum of 5 mins. to a maximum of 20 mins.
The unit will automatically turn off after 30 mins. when there is no signal.
A RED logo flashing one single time every 2 seconds means:
-AP8.9 bit temperature reached 75° C and the thermal protection was triggered. It will start operating again at
around 70° C.
A RED logo flashing twice every second means:
- Outputoverload.TheredLEDflasheswhentheoutputloadgoesbelowtheminimumallowedcapacityofabout2Ω
impedance. The LED comes on without flashing, activating the protection. When listening to music,
if the acoustic reproduction stops for a few seconds, check if the red amplifier LED is flashing.
This means there was an overload. Turn the amplifier off and check the speakers and wirings.
-Speaker wiring anomaly. The red LED flashes when a terminal on the speaker goes in short-circuit with the
vehicle chassis. When listening to music, if the acoustic reproduction stops for a few seconds, check to see
if the red amplifier LED is flashing; this means there was a short circuit between a terminal on a speaker and
the vehicle chassis. Turn off the amplifier and check the speakers and wiring.
A RED logo flashing four times every second means:
-The “OVER VOLTAGE” protection activation, due to the fact that the battery voltage is higher than 16V. The
product will turn off after 3 minutes.
WARNING: Check the state of charge of the car alternator.
A RED logo means:
-Product internal fault. You have to go to an authorized service centre. The product will turn off after 3 minutes.
4
11
10
12

AP8.9 bit /
10
USER’S MANUAL
5. CONNECTIONS
5.1 POWER SUPPLY AND REMOTE TURN ON
AP8.9 bit is on when the logo is lit blue. It can be turned on/off using the following methods:
1. By pressing on the main DRC control knob (ON). By holding down the main control knob on the DRC (OFF).
In this case, no other Remote In connections are needed, but they can co-exist.
2. By connecting the REMOTE IN terminal with a Remote Out signal coming from an after market audio source.
3. Through the Hi Level MASTER (FL - FR) input. The AUTO TURN ON (ART) function is activated by connecting
the output of an amplified source to the INPUT FL - FR input channel. This function can be enabled/disabled
using AP8.9 bit PC software (see sec. 7.3.4.7).
4. Using the Low Level (Pre Out) input. The AUTO TURN ON (AST) function is activated by connected the outputs on a
preamplified source to the input channels to the AP8.9 bit input channels. This function can be enabled/disabled
using AP8.9 bit PC Software. This turn on control is available on the FL FR RL RR IN1 IN2 inputs (see sec. 7.3.4.7).
5. By connecting the OPTICAL SELECT / AUX IN SELECT terminal with a Remote Out signal coming from an auxiliary
source, or connecting to terminal to 12V. This function can be enabled/disabled using AP8.9 bit PC Software (ee sec. 7.3.4.7).
Turn AP8.9 bit on and off
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
(Not provided.
Suggested Fuse
30 A delayed)
Max 20 cm / 7.9 in.
15 mm / 0.6 in.
8 AWG Max
SD
REMOTE OUT
REMOTE OUT
pink OPTICAL SELECT
AUX SELECT
blue REM IN blue/white REM OUT
REM IN
EXTERNAL SUBWOOFER
AMPLIFIER (Optional)
OPTICAL SOURCE
HEAD UNIT
brown MASTER ENABLE + 12 V
+ 12 V
*(see sec. 7.3.4.7)
5
HEXKEY 2,5 mm

11
AP8.9 bit /
USER’S MANUAL
1. SPEAKER IN HI-LEVEL FRONT + REAR
3. SPEAKER IN HI-LEVEL FRONT + REAR + CENTER + SUB 4. SPEAKER IN HI-LEVEL FRONT + REAR +
AUXILIARY STEREO SOURCE
5.2 INPUT SIGNALS
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
01
2
3
4
5
6
7
01
2
3
4
5
6
7
01
2
3
4
5
6
7
01
2
3
4
5
6
7
SD
SD
SD
SD
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
01
2
3
4
5
6
7
01
2
3
4
5
6
7
01
2
3
4
5
6
7
01
2
3
4
5
6
7
SD
SD
SD
SD
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
01
2
3
4
5
6
701
2
3
4
5
6
7
01
2
3
4
5
6
7
01
2
3
4
5
6
7
SD
SD
SD
SD
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
OFF ON
REM IN
30A
01
2
3
4
5
6
701
2
3
4
5
6
7
01
2
3
4
5
6
7
01
2
3
4
5
6
7
SD
SD
SD
SD
white
green
gray
violet
white/black
green/black
gray/black
violet/black
FL+
RL+
FR+
RR+
FL-
RL-
FR-
RR-
white
green
gray
violet
white/black
green/black
gray/black
violet/black
white
green
gray
violet
white/black
green/black
gray/black
violet/black
FL+
RL+
FR+
RR+
FL-
RL-
FR-
RR-
IN1+
IN2+
IN1-
IN2-
white
green
gray
violet
white/black
green/black
gray/black
violet/black
FL+
RL+
FR+
RR+
FL-
RL-
FR-
RR-
IN1+
IN2+
IN1-
IN2-
IN1
IN2
AUXILIARY STEREO
PREAMPLIFIER SOURCE
5. MASTER PRE IN FRONT + REAR + CENTER + SUB + REAR 6. MASTER PRE IN FRONT + REAR
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
SD
SD
SD
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
SD
SD
SD
CENTER OUT
SUB OUT
FRONT LEFT
FRONT RIGHT
REAR LEFT
REAR RIGHT
FL
RL
FR
RR
FRONT LEFT
FRONT RIGHT
REAR LEFT
REAR RIGHT
FL
RL
IN1
FR
RR
IN2
ACP 2
(optional)
(see sec. 10.2)
ACP 6
(optional)
(see sec. 10.3)
ACP 6
(optional)
(see sec. 10.3)
5
cyan
orange
cyan/black
orange/black
cyan
orange
cyan/black
orange/black
2. SPEAKER IN HI-LEVEL FRONT WOOFER + FRONT TW + REAR
FRONT TW
RIGHT
SUB
FRONT TW
LEFT
CENTER
FL WF+
RL+
FR WF +
RR+
FL WF-
RL-
FR WF-
RR-

AP8.9 bit /
12
USER’S MANUAL
7. MASTER PRE IN FRONT + REAR + AUXILIARY STEREO SOURCE 8. AUX IN L/R
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
SD
SD
SD
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
SD
SD
SD
AUXILIARY STEREO
PREAMPLIFIER SOURCE
AUXILIARY STEREO
PREAMPLIFIER SOURCE
MP3 PLAYER
IN1
IN1
FRONT LEFT
FRONT right
REAR LEFT
REAR RIGHT
FL
RL
FR
RR
IN2
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
SD
SD
SD
AUXILIARY STEREO
PREAMPLIFIER SOURCE
MP3 PLAYER
IN1
IN2
IN2
1.Using the DRC, selecting the OPTICAL input.
2.Using the appropriately set OPTICAL IN terminal (see sec. 7.3.4.7).
This command is active connecting the terminal to + 12V.
How to select OPTICAL input:
5.3 DIGITAL OPTICAL IN INPUT SIGNALS
WARNING: The digital inputs accepts up to 96 kHz / 24 bit stereo PCM signals. So DOLBY DIGITAL (AC3) multi-channel signals
coming from audio/video sources (such as the audio of a film in DVD) or DTS can not be reproduced. The output of
these devices will therefore have to be set in STEREO mode for the signal to be reproduced. If digital signals at
frequency higher than 96kHz (Ex. 192 kHz) are supplied, the AP8.9 bit will not be able to reproduce them.
OPTICAL FIBER (see sec. 10.7; 10.8)
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
TOSLINK connector
PCM Stereo signal, max 96 kHz / 24 bit
ACP 2
(optional)
(see sec. 10.3)
ACP 6
(optional)
(see sec. 10.3)
ACP 2
(optional)
(see sec. 10.3)
5

13
AP8.9 bit /
USER’S MANUAL
5.4 OUTPUT SIGNALS
01
2
3
4
5
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
16: White OUT 1+
15: White OUT 2+
14: White OUT 3+
13: White OUT 4+
12: White OUT 5+
11: White OUT 6+
10: White OUT 7+
9: White OUT 8+
8: White/Black OUT 1-
7: White/Black OUT 2-
6: White/Black OUT 3-
5: White/Black OUT 4-
4: White/Black OUT 5-
3: White/Black OUT 6-
2: White/Black OUT 7-
1: White/Black OUT 8-
2
1
1. AP8.9 bit provides 8 amplified outputs. Through the PC Software, each output channel has the following available
(ee sec. 7.2):
-a 10 pole graphic equalizer;
-a 68-frequency electronic crossover and Butterworth or Linkwitz-Riley type filters with 6-24 dB slopes (see sec. 7.3.10);
-a digital time delay line (see sec. 7.3.11);
-Phase inversion activation (see sec. 7.3.10.2);
-Adjustment of the output level to better align the total system response (see sec. 7.3.13);
2. AP8.9 bit features one a preamplified output (4 V Rms max.) SUB OUT that exclusively controls a mono amplifier
for subwoofer, or one active subwoofer to amplify the sound system. This output can be activated during I/O Wizard
Configuration (see sec. 7.2.9).
CONFIGURAZIONE CANALI D’USCITA AMPLIFICATI CH1÷CH8
STEREO MODE
POWER CHANNEL CONFIG
BRIDGE MODE
CH1 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH2 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH3 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH4 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH5 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH6 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH7 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH8 35 W @ 4 Ohm / 65 W @ 2 Ohm
CH1+ / CH2- 130 W @ 4 Ohm
CH3+ / CH4- 130 W @ 4 Ohm
CH5+ / CH6- 130 W @ 4 Ohm
CH7+ / CH8- 130 W @ 4 Ohm
5
CH 1÷CH 8 AMPLIFIED OUTPUT CHANNELS CONFIGURATION

AP8.9 bit /
14
USER’S MANUAL
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
5.4.1 PRESET 0DEFAULT: 3 WAY ACTIVE FRONT + REAR.
1
2
3
4
5
6
70
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 FRONT TW LEFT HI PASS Linkwitz 5000 Hz @12 dB 0 35 W 65 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 5000 Hz @12 dB 0 35 W 65 W
OUT 7 REAR LEFT FULL HI PASS Linkwitz 80 Hz @12 dB 0 35 W 65 W
OUT 8 REAR RIGHT FULL HI PASS Linkwitz 80 Hz @12 dB 0 35 W N. A.
OUT 3 FRONT MD LEFT BAND PASS Linkwitz 500 Hz @12 dB 0 35 W 65 W
3000 HZ @ 12 dB
OUT 4 FRONT MD RIGHT BAND PASS Linkwitz 500 Hz @12 dB 0 35 W 65 W
3000 HZ @ 12 dB
OUT 5 FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB 0 35 W 65 W
500 HZ @ 12 dB
OUT 6 FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB 0 35 W 65 W
500 HZ @ 12 dB
SUB OUT SUB WOOFER LO PASS Linkwitz 80 Hz @12 dB 0 - -
OUTPUT CONFIGURATION:
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
Out 1 (+) Out 8 (+) Out 3 (+) Out 6 (+) Out 5 (+) Out 4 (+) Out 7 (+) Out 2 (+) Out 1 (-) Out 8 (-) Out 3 (-) Out 6 (-) Out 5 (-) Out 4 (-) Out 7 (-) Out 2 (-)
REAR
LEFT
WF
LEFT
FRONT
MD
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
MD
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
RIGHT
5
to SUBWOOFER amplifier

15
AP8.9 bit /
USER’S MANUAL
5.4.2 PRESET 1: 2 WAY ACTIVE FRONT + 2 WAY PASSIVE REAR + SUBWOOFER
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
MEMORY CONFIGURATION:
Memory A: Acoustic
Memory B: Rhythm
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 FRONT TW LEFT HI PASS Linkwitz 3000 Hz @12 dB 82,2 cm 35 W 65 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 3000 Hz @12 dB 116,2 cm 35 W 65 W
OUT 7 + 8 SUBWOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm 130 W N. A.
OUT 6 REAR RIGHT HI PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
OUT 5 REAR LEFT HI PASS Linkwitz 80 Hz @12 dB 62,3 cm 35 W 65 W
OUT 3 FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB 82,2 cm 35 W 65 W
3000 HZ @ 12 dB
OUT 4 FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
3000 HZ @ 12 dB
OUTPUT CONFIGURATION:
*Listening Point: Driver
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456
76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
Out 1 (+) Out 6 (+) Out 3 (+) Out 4 (+) Out 5 (+) Out 7 (+) Out 2 (+) Out 1 (-) Out 6 (-) Out 3 (-) Out 4 (-) Out 5 (-) Out 8 (-) Out 2 (-)
SUBWOOFER
REAR
LEFT
WF
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
RIGHT
1
2
3
4
5
6
70
5

AP8.9 bit /
16
USER’S MANUAL
5.4.3 PRESET 2: 3 WAY ACTIVE FRONT + SUBWOOFER
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
MEMORY CONFIGURATION:
Memory A: Acoustic
Memory B: Rhythm
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 FRONT TW LEFT HI PASS Linkwitz 3000 Hz @12 dB 82,2 cm 35 W 65 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 3000 Hz @12 dB 116,2 cm 35 W 65 W
OUT 7 + 8 SUBWOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm 130 W N. A.
OUT 3 FRONT MD LEFT BAND PASS Linkwitz 500 Hz @12 dB 82,2 cm 35 W 65 W
3000 HZ @ 12 dB
OUT 4 FRONT MD RIGHT BAND PASS Linkwitz 500 Hz @12 dB 116,2 cm 35 W 65 W
3000 HZ @ 12 dB
OUT 5 FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB 82,2 cm 35 W 65 W
500 HZ @ 12 dB
OUT 6 FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
500 HZ @ 12 dB
OUTPUT CONFIGURATION:
*Listening Point: Driver
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
Out 1 (+) Out 6 (+) Out 7 (+) Out 3 (+) Out 4 (+) Out 5 (+) Out 2 (+) Out 1 (-) Out 6 (-) Out 8 (-) Out 3 (-) Out 4 (-) Out 5 (-) Out 2 (-)
SUBWOOFER
MD
LEFT
FRONT
WF
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
MD
RIGHT
FRONT
TW
RIGHT
FRONT
1
2
3
4
5
6
70
5

17
AP8.9 bit /
USER’S MANUAL
5.4.4 PRESET 3: FRONT + REAR + SUBWOOFER
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
MEMORY CONFIGURATION:
Memory A: Acoustic
Memory B: Rhythm
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 + 2- FRONT LEFT HI PASS Linkwitz 80Hz @12 dB 82,2 cm 130 W N. A.
OUT 3 + 4- FRONT RIGHT HI PASS Linkwitz 80 Hz @12 dB 116,2 cm 130 W N. A.
OUT 5 REAR LEFT HI PASS Linkwitz 80Hz @12 dB 62,3 cm 35 W 65 W
OUT 6 REAR RIGHT HI PASS Linkwitz 80Hz @12 dB 116,2 cm 35 W 65 W
OUT 7 + 8- SUBWOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm 130 W N. A.
OUTPUT CONFIGURATION:
*Listening Point: Driver
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
SUBWOOFER
REAR
LEFT
FRONT
LEFT
REAR
RIGHT
FRONT
RIGHT
Out 1 (+) Out 6 (+) Out 5 (+) Out 3 (+) Out 7 (+) Out 2 (-) Out 6 (-) Out 5 (-) Out 4 (-) Out 8 (-)
1
2
3
4
5
6
70
5

AP8.9 bit /
18
USER’S MANUAL
5.4.5 PRESET 4: 2 WAY ACTIVE FRONT + REAR + SUB
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
MEMORY CONFIGURATION:
Memory A: Acoustic
Memory B: Rhythm
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 FRONT MD TW LEFT HI PASS Linkwitz 500Hz @12 dB 82,2 cm 35 W 65 W
OUT 2 FRONT MD TW RIGHT HI PASS Linkwitz 500 Hz @12 dB 116,2 cm 35 W 65 W
OUT 5 REAR LEFT HI PASS Linkwitz 80 Hz @12 dB 62,3 cm 35 W 65 W
OUT 6 REAR RIGHT HI PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
OUT 7 + 8- SUBWOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm 130 W N. A.
OUT 3 FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB 82,2 cm 35 W 65 W
500 HZ @ 12 dB
OUT 4 FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
500 HZ @ 12 dB
OUTPUT CONFIGURATION:
*Listening Point: Driver
1
2
3
4
5
6
70
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
Out 1 (+) Out 3 (+) Out 5 (+) Out 7 (+) Out 6 (+) Out 4 (+) Out 2 (+) Out 1 (-) Out 3 (-) Out 5 (-) Out 8 (-) Out 6 (-) Out 4 (-) Out 2 (-)
SUBWOOFER
WF
LEFT
FRONT
MD
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
MD
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
LEFT REAR RIGHT
5

19
AP8.9 bit /
USER’S MANUAL
5.4.6 PRESET 5: 3 WAY ACTIVE FRONT + REAR + EXTERNAL AMPLIFIED SUB
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
MEMORY CONFIGURATION:
Memory A: Acoustic
Memory B: Rhythm
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 FRONT TW LEFT HI PASS Linkwitz 3000Hz @12 dB 82,2 cm 35 W 65 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 3000 Hz @12 dB 116,2 cm 35 W 65 W
OUT 7 REAR LEFT HI PASS Linkwitz 80 Hz @12 dB 62,3 cm 35 W 65 W
OUT 8 REAR RIGHT HI PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W N. A.
SUB OUT SUB WOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm - -
OUT 3 FRONT MD LEFT BAND PASS Linkwitz 500 Hz @12 dB 82,2 cm 35 W 65 W
3000 HZ @ 12 dB
OUT 4 FRONT MD RIGHT BAND PASS Linkwitz 500 Hz @12 dB 116,2 cm 35 W 65 W
3000 HZ @ 12 dB
OUT 5 FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB 82,2 cm 35 W 65 W
500 HZ @ 12 dB
OUT 6 FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
500 HZ @ 12 dB
OUTPUT CONFIGURATION:
*Listening Point: Driver
1
2
3
4
5
6
70
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
Out 1 (+) Out 8 (+) Out 3 (+) Out 6 (+) Out 5 (+) Out 4 (+) Out 7 (+) Out 2 (+) Out 1 (-) Out 8 (-) Out 3 (-) Out 6 (-) Out 5 (-) Out 4 (-) Out 7 (-) Out 2 (-)
SUBWOOFER
REAR
LEFT
WF
LEFT
FRONT
MD
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
MD
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
RIGHT
5

AP8.9 bit /
20
USER’S MANUAL
5.4.7 PRESET 6: 2 WAY ACTIVE FRONT + REAR + EXTERNAL AMPLIFIED SUB
INPUT CONFIGURATION:
Master input: Front + Rear
Aux input: In1 + In 2
Optical: S/P-DIF PCM 96kHz/24 bit max
MEMORY CONFIGURATION:
Memory A: Acoustic
Memory B: Rhythm
OUTPUT TYPE CUT FILTER FILTER TYPE CUT FREQUENCY TIME ALIGNMENT* POWER @ 4Ω POWER @ 2Ω
OUT 1 FRONT TW LEFT HI PASS Linkwitz 3000Hz @12 dB 82,2 cm 35 W 65 W
OUT 2 FRONT TW RIGHT HI PASS Linkwitz 3000 Hz @12 dB 116,2 cm 35 W 65 W
OUT 7 REAR LEFT HI PASS Linkwitz 80 Hz @12 dB 62,3 cm 35 W 65 W
OUT 8 REAR RIGHT HI PASS Linkwitz 80 Hz @12 dB 116,2 cm 35 W 65 W
SUB OUT SUB WOOFER LO PASS Linkwitz 80 Hz @12 dB 121,8 cm - -
OUT 3+ 4- FRONT WF LEFT BAND PASS Linkwitz 80 Hz @12 dB 82,2 cm 130 W N. A.
3000 HZ @ 12 dB
OUT 5+ 6- FRONT WF RIGHT BAND PASS Linkwitz 80 Hz @12 dB 116,2 cm 130 W N. A.
3000 HZ @ 12 dB
OUTPUT CONFIGURATION:
*Listening Point: Driver
0
1
2
345
6
7
POWER - 12V USB
OPTICAL SEL.
12345123456 76 8
UPGRADEPRESETS
SPEAKER
OUT
OPTICAL IN DRC
SUB OUT
INPUTS
ASP
OFF ON
REM IN
REM OUT
MASTER ENABLE
30A
Out 1 (+) Out 8 (+) Out 3 (+) Out 5 (+) Out 7 (+) Out 2 (+) Out 1 (-) Out 8 (-) Out 4 (-) Out 6 (-) Out 7 (-) Out 2 (-)
SUBWOOFER
REAR
LEFT
WF
LEFT
FRONT
TW
LEFT
FRONT
WF
RIGHT
FRONT
TW
RIGHT
FRONT
REAR
RIGHT
1
2
3
4
5
6
70
5