Aurine A4-E6C-56 User manual

VIDEO DOOR PHONEIN
A4-E6C-56 (COLOR)
A4-E6C-56
A C
(100-240V)
4
A-121/
A-122
Door
Release
Power
( ) Optional Accessories
Mounting Bracket
I Monitorndoor Phone( )
1
Ⅵ.OPERATION
Buzz
4
A4-M1C A4-M2C A4-M4C
O R O R
4# Line
2# Line
Handset
Introduction
The model number is located on
number in the space provided below .Refer to these numbers whenever
you call upon your dealer regarding this product.
the bottom and record the serial
This symbol is intended to alert the user to the
presence of uninsulated “ ”
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
Electric shock to persons.
dangerousvoltage
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) intructions in the literature accompanying
the appliance.
Ⅰ. SYSTEM OUTLINE COMPONENTS.E6 Ⅱ. PA RT S C H E C K L I S T
Ⅶ.TROUBLE SHOOTING GUIDE
Read and perform the following procedures carefully before returning Your Video Doorphone for repair and replacement.
SPECIFICATIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK,DO NOT REMOVE
COVER (OR BACK). NO USERSERV-
ICEABLE PARTS INSIDE. REFER SE-
RVICING TO QUALIFIED SERVICE PE-
RSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : -
SK OF FIRE OR SHOCK HA
DO NOT EXPOSE THIS EQUIPM-
ENT TO RAIN OR MOISTURE
TO REDUCE THE RI
ZARD
CAUTION: TO REDUCE THE RISK
OF FIRE OR SHOCK HAZARD AND
ANNOYING INTERFERENCE,USE
THE RECOMMEDED ACCESSO-
RIES ONLY
CAUTION: TO REDUCE THE RISK
OF FIRE OR SHOCK HAZARD，
REFER CHANGE OF SWITCH SE-
TTING INSIDE THE UNIT TO QU-
ALFIED SERVICE PERSONNEL
Place the power “O/I” switch on the “I”position.
Use the bottom knobs to adjust contrast and brightness.
1.Visitor presses the “CALL” button on the Outdoor Camera, the Indoor Phone will sound
“Dingding—dong---” to announce that a visitor is at the door.
2.Press the button to monitor doorway 1, and press it again to monitor doorway 2.
Then press the button to end the monitoring.
3.After the visitor's image shown on the screen,you may
A. refuse to answer the call (the visitor's image will disappear after 90 seconds).
B. pick up the handset/ press button to answer the call (time limit for video talk:80
seconds) ; to end the talk, hang up/ press button.
4.During the talk, press button to release the door, if the door is equipped with e-lock.
CAUTION: TO REDUCE THE RISK
OF FIRE OR SHOCK HAZARD,RE
-FERMOUNTING OF THE OPTI-
ONAL INTERFACE BOARD TO
QUALIFIED
SERVICE PERSONNEL
No.
1
Problem Possible Cause
Unit totally dead.(Power lamp OFF)
* The power cord is not properly inserted in the AC outlet, or the
AC is not supplied.
* The power ON/OFF switch is on the OFF position.
Unit totally dead. (Power light dim) *
wrong wiring.
The wires between the phone and the camera are shorted or
2
3
4
Can call and communicate,however, monitor
screen illuminates without picture.
Can call and communicate,however, there is
no video signal.
* Brightness control is not pr o p erly adjusted.
* Defective camera
Sub-Phone or Interphone
Voltage Requirements
Power Consumption
Monitor Screen
Voltage adaptability 100V-240V,50/60Hz
Maximum 35VA; stand by 1VA.
7”COLOR5.6”COLOR
Audio Communication System
Maximum Wiring Distance
Extensions
Ambient Temperature
Net Weight
Dimension(W H D)× ×
Duplex handset.
50m/16 feet (22 AWG,0.65mm4wire)
-10℃ to +40℃
0.783 Kg
Model No.
A4-E6C-7A4-E6C-56
Plink
7”COLOR
A4-E6C-7-R
A4-E6C-7 (COLOR) A4-E6C-7-R (COLOR)
A4-E6C-7
A4-E6C-7-R
V090615
MFS0402E
Ringtone
Ding-ding dong adjustable volume
Indoor Phone(Monitor)
Mounting Bracket
Screw(ST4×25mm)
Connection Cable
4# line
Plastic Wall Plug
1
2
2
2
1
1
Handset 1
User Manual 1
2# line
Screw
User Manual
Plastic Wall Plug
270mm 137.9mm 54.1mm× ×

Ⅲ.FEATURES
Ⅳ.WIRING
2
OUTDOOR1 OUTDOOR2 IMAGE
1 2
5
#3 6#4 7
ImageMemory
(
)
Optional
Accessories
125
3 6
47
Release
Camera1
4
1 2 3 4
32
1
Door
A-121/
A-122
Power
(
)
Optional
Accessories
1 2 3 4
Release
Camera2
432
1
Door
A-121/
A-1 2 2
Power
(
)
Optional
Accessories
6. Talk Button
7. Power “O/I” S/W
Used to turn AC power“O” and“I”
8. COL Contrast ControL
To control contrast of screen, to control chroma
of LCD
9. BRI Brightness Control S/W
Used to adjust brightness level of the Screen.
10. VOL Volume Control
11. Ringtone Volume Control
1. Handset
Used for two-way communication with the v isitor.
2. Screen
Displays image of a visitor o r the camera viewing
area.
3. Power LED
Illuminates when power S/W is in “ON” position.
4. Monitor Button
Press to activate the outside camera and screen to
see c amera viewing area.
5. Door Release Button
Used to unlock an electronic door locking system.
1 0
Camera2
Camera1
44 33 22 11
Door
Release
Door
Release
Power ( ) Optional AccessoriesPower ( ) Optional Accessories
A-121/A-12 2A-121/A-1 2 2
INDOOR PHONE
11 22 33 44
OUTDOOR1 OUTDOOR2
7
6#3 5 2#4
1
IMAGE
Door
Release
4
321
INDOOR PHONE
Camera2
A-121/A-122
Power ( ) Optional Accessories
11 22 33 44
OUTDOOR1 OUTDOOR2
7
6#3 5 2#4
1
IMAGE
OU T DO OR 1 O UT DO OR 2
IMAGE
11
1
1 2 3 4 5 6 7 8
2 3 4 1 2 3 4
VOL
Mounting
Bracket
Mounting
Screw
3
Handset Indoor Phone
Plug
AC SWITCH
Note: Using the component “2# Line” to connect #3,#4 shut pin when you are not using image
memory
Wiring is not supplied with your Video Doorphone system.Use only AWG #22 wire (0.65mm,
4-wire) and follow the appropriate wiring diagrams exactly for optimum system performance
and safety.
When planning to install the initial system , consider future system extension. The total wire
length for a single camera and monitor system(or any combination of additional camera or
monitors) must not exceed 50m for optimum performance.
* OPTION 2 (TWO CAMERAS/ INDOOR PHONE/IMAGE MEMORIER)SINGLE
Ⅴ.INSTALLATION
Important Mounting Notes:
Do not install the monitor and camera units where they will be exposed to dirt,
direct sunlight (or other strong light) , moisture ,high temperature 40℃)
or high humidity conditions.
Do not select an installation location subjected to vibration or pounding.
Select a mounting location close to an AC outlet where it is easy to view the
screen and operate the monitor.
( over
1.Determine the mounting locations for the outside camera
inside monitor.
2.At the selected monitor mounting location , attached the mounting bracket
securely to t h e wall, drill a h ole in the center area of the bra cket just large
enough for the electrical wirin g to pull through the hole. Connect the ele ctrical
w ires from the camera unit to the monitor..
3.Connect the handset cord to the monitor unit.
4.Attach the wired monitor unit to the wall mounting bracket by setting the
monitor over the four bracket hooks and sliding it down , Insert the tiny
machi ne s crew into the hole in the tab at the top of the bracket to hold the
monitor in place.
5.Plug the AC power cord into a standard household outlet.
6.Place the power“ON/OFF”switch on the “On” position.
both and
AWG 22
Wrie
(0.65mm)
7
o
I
INDOOR PHONE
Power ( ) Optional AccessoriesPower ( ) Optional Accessories
IMAGE
1 2 5#3 6#4 7
Image Memory
(
)
Optional
Accessories
125
3 6
47
O U T D O O R 2
12 3 4
Door
Release
Camera2
A-121/A-122
4
321
OUTDOOR1
12 3 4
Door
Release
Camera1
A-121/A-122
4
321