AUROOM Arti User manual

Outdoor sauna ''Arti''
Installation manual

FE-1
1. Check substructure level. Sauna must be installed on a level surface.
1. Floor element

1. Start assembly from corner A WALL and B WALL. Place the elements on previously
assembled and stable floor element and fix with screws as indicated on Figure 2a and 2b.
2. Wall elements
Top view
Figure 2b.
CC 400mm
C WALL
B WALL
A WALL
Corner fixing
Figure 2c.
Corner fixing
Figure 2c.
Bottom fixing
Figure 2b.
Bottom fixing
Figure 2a.
Bottom fixing
Figure 2b.

1. Place the roof element on top of previously installed and fixed wall elements. Check walls
for vertical level. Ceiling element must sit flush with walls external layer and with no
excessive gaps between internal panels. Fix with screws.
2. Install the ceiling as the previous. Check the front edge between ceiling and wall - they
must fit flush.
NOTE! Do not support elements on edge of previous installed element!
3. Roof element
ROOF ELEMENT
Top fixing
Figure 3a.
Top fixing
Figure 3a.

4. Glasswall
1. Fit the door to previously installed elements.
2. Check for level.
3. Fix the door with brackets and foam.
NOTE! Do not remove protection material from door until it is finally and properly fitted.

5. Electrical work
1. Before fixing interior loose boards or other panels, do all the necessary electrical work.
NB! ALL ELECTRICAL CONNECTIONS MUST BE MADE BY CERTIFIED ELECTRICIAN!
MAIN CABLE (INCOME)

6. Side panels
1. Start assembly from VK-1 to VK-4. Place the panels on previously assembled and
stable elements and fix with screws as indicated on Figure 6a.
2. NOTE! There is a small board in PK-4 panel that you have to slide in its place.
3. Fix top panels through board with black screws.
VK-1
VK-2
VK-3
VK-4
PK-1
PK-2
PK-3
PK-4
PK-5
66
Side fixing
Figure 6a.
Side fixing
Figure 6a.
Side fixing
Figure 6a.
28
View from top
Figure 6b.
Figure 6b.

7. Side door for electrical box
1. Place the door in a hole in exterior panels. Fix the door with screws trough hinge.
2. Fixe loose bottom boards with black screws.
Figure 7a.
View from top
Figure 7a.

8. Back panels
66
Back fixing
Figure 8a.
View from top
Figure 8b.
Figure 8b.
Back fixing
Figure 8a.
1. Start assembly from TK-1 to TK-4. Place the panels on previously assembled and stable
elements and fix with screws as indicated on Figure 8a.
2. Fix top panels through board with black screws.
TK-1
TK-2
TK-3
TK-4

9. Corner mouldings and loose bottom board
1. Fix the bottom loose board with black screws.
2. Corner pieces are fixed with small nails or screws.

10. Terrace side panels
1. Start assembly from A side to C side. Place the elements on previously assembled and
stable elements and fix with screws as indicated on Figure 10a.
2. After fixing panels, slide loose boards in empty places.
3. Make sure the electrical cables are attached and fixed before fixing side panels.
Against the ceiling
Figure 10a.
Front view
Front view
Figure 10a.

11. Terrace ceiling panels
1. Start assembly from TLL-1 to TLL-2. Place the panels on previously assembled and
stable elements and fix with screws as indicated on Figure 10a.
2. After fixing panels, slide loose boards in empty places.
3. Make sure the electrical cables are attached and fixed before fixing side panels.
Figure 11a.
TLL-1
TLL-2
Front view
Figure 11a.
Front view

12. Front panels
EK-1
EK-2
EK-3
EK-4
1. Start assembly from EK-1 to EK-4. Place the panels on previously assembled and
stable elements and fix with screws as indicated on Figure 12a and 12b.
2. Fix top panels through board with black screws.
Black screws
Top fixing
Figure 12a.
Bottom fixing
Figure 12b.
Black screws
66
Bottom fixing
Figure 12b.
Top fixing
Figure 12a.

13. Front corner mouldings
1. Corner pieces are fixed with small nails or screws.

14. Terrace floor grid
1. Carefully set the terrace floor grid to its place.
TERRACE FLOOR GRID

15. Roof stains
1. Stains are fixed with special black screws.

16. Interior loose boards
1. Before fixing boards, make sure all the necessary cables are installed.
2. Boards are fixed with brown screws as indicated on Figure 16a.
Electrical cables
in this box
Figure 16a.

17. Floor grids
1. Start placing floor grids from back to front.
1
2
3

18. Bench supports, backrest supports
1. Place bench supports in sauna, check for level.
2. Fix bench supports with screws.
3. Fix backrest supports with screws.
1
2
3

19. Horizontal bench frames
1. Fix backrest with screws as shown (Figure 19a).
2. Place upper bench frame and fix with screws.
3. Place lower bench frame and fix with screws.
NOTE! First fasten the screws on side walls, then back wall.
Figure 19a.
Backrest
1
2
3