AUS PRO CL-200E User manual

PRO CL-200E
Automatic money detector
English
User manual

2
English
PRO CL-200E specially designed for verifying EURO banknotes.
The present detector automatically carries out a complex analysis for
authentication and gives a well-defined result, what enables operator to test banknotes
quickly, without any special knowledge about false banknote protection types. By means
of this device you can test a banknote in less than 1 sec, see the total sun and quantity
of verified banknotes. The detector is designed for use in: cash desks, banks, currency
exchange offices and other specialized organizations making high demands to banknote
authentication verification. The detector is user-friendly, what makes it possible for use
in supermarkets, accounting departments, offices, and even automobiles by means of
connecting it to cigarette lighter socket through adapter.
Distinctive features
- Designed for EURO banknotes verification
- Any orientation of notes in receiving tray
- High verification speed, up to 90 banknotes/1 min.
- Infra-red detection. Checks IR marks location.
- Magnetic detection. Checks magnetic marks presence.
- Optical density detection.
- Banknote size detection.
- Nominal value detection.
- Summing up by nominal values.
- 3-digit LED display showing the number of counted banknotes
- 6-digit LED display showing the sum of counted banknotes
- Sound and code indication of false banknotes
- Direct and reversal banknote supply mode
- The ability to use in automobile
1 Specification
- Verification speed, banknote/min (max) ....................................................................90
- Supply voltage, V .......................................................................................................12
- Consumption current, mA ........................................................................................800
- Power supply .............................................................100-240V, 50/60Hz (AC adapter)
- Operating temperature, degrees 0C............................................................+10..+40 0C
- Overall dimensions (l/w/h), mm .................................................................220x80x120
- Weight, kg .............................................................................................................0,75

3
English
2 Appearance
1. Receiving tray.
2. Opening top cover. In case of banknote jam open the cover and remove the jammed
banknote.
3. ‘+’ button switches on ‘Add’/ off ‘onE’ mode of summing up nominal values. If hold ‘+’
button for 3 seconds, banknote supply mode switches (forward/backward).
4. ‘C’ button. Clears display values.
5. 3-digit LED display showing the quantity of counted banknotes.
6. 6-digit LED display showing the nominal of counted banknotes.
7. Power switch off.
8. Banknote supply mode indicators. The upper indicator corresponds with forward
supply mode, the lower one- backward supply.
3 Operation
1. By means of the supplied ac adapter connect the detector to the mains of 100-240V
50/60Hz.
2. Switch power on, Fig 1-7. Detector enters self testing mode. ‘PRO CL-200’ will be
displayed, wait for a few seconds. After self testing the detector is ready for operation.
The upper and lower display should display ‘0’ value, see Fig.3.
3. If needed select banknote supply mode.
In case of forward supply mode, after a banknote is tested it will be placed from the left
side (as shown on Fig.2) and a banknote, which has not passed the test, will be placed
1
2
3
45
6
7
8
Figure 1

4
English
from the right side (as shown on Fig.2). To set forward and backward supply mode hold
‘+’ button for 3 seconds. The upper green indicator corresponds to forward mode and
the lower indicator – backward mode.
4. The detector has 2 operation modes: ‘onE’ one banknote verification mode and ‘Add’
nominal valued summing up mode.
The upper display shows the quantity of counted banknotes in ‘Add’ mode, while in ‘onE’
mode the display value is equal to 1.
The lower display shows the sum of banknotes by their nominal values in ‘Add’ mode,
while in ‘onE’ one banknote verification mode the valued is equal to the nominal value
of the banknote. Set ‘onE’ one banknote verification mode or ‘Add’ summing up mode.
To do this press ‘+’.
5. Place a banknote into receiving tray as shown on Fig.4, tightly pressing an edge of
banknote to any side of receiving tray.
The detector will determine the nominal of authentic banknote (in ‘Add’ mode it will add
its nominal to the total sum).
Figure 4
Figure 3
Figure 2

5
English
Attention! If a banknote is placed in receiving tray incorrectly, the banknote is not
detected as an authentic one and any error code is displayed.
In case of error check banknote orientation (Fig.4) and try to place the banknote into
receiving tray once again.
When counting is over, clear the display pressing ‘C’ button and switch off the power. If
a banknote is jammed inside the detector, open the top cover (Fig 1-2) and remove the
banknote.
4 Mounting and maintenance rules
1. When choosing a mounting place for detector, avoid uneven and water-close surfaces
and dangerous objects.
2. Do not mount and so not use the detector in places where it can be affected by direct
sunlight, strong vibration and dust.
3. Use the adapter supplied with the device.
4. If the device was kept in cold for a long time, keep it for at least 6 hours without
packing at a room temperature before switching on.
5. Switch off detector when it is not used for a long time during a day.
6. Error codes and messages.
Attention! Errors may occur when verifying authentic crumpled, dilapidated, dirty,
laundered, torn, taped, decoloured banknotes or if a banknote was exposed to hostile
environment or has foreign inscriptions.
Attention! New pattern banknotes may be issued. If there are errors in operation of
detector during banknote verification, install a new firmware in service centre. During the
warranty period new firmware is installed for free.
Figure 5 Figure 6
Correct orientation of notes Incorrect orientation of notes
Right edge Center Left edge
Orientation to:

6
English
5 Troubleshooting
Error Code Reason Solution
En Magnetic marks location
error
1. Check the correctness of
placement banknote into detector
(see Fig.4)
2. Count the banknote again. If an
error occurs again, the banknote
can not be detected as authentic
Ei Infra-red marks location error
EF Banknote image detection
error
Ed Paper quality error
dd Banknote size is incorrect
EP Colour printing quality error
ES A combination of above
mentioned errors
Eh Top cover is open Close top cover 2
Ec Wrong capture of banknote
or banknote wreck
1. Place the banknote one more
time.
2. Open the top cover and clean
detector duct

7
English
Warranty
Manufacturer guarantees proper functioning of the device during warranty period since
the date of sale under condition of compliance with maintenance and storage
procedures described in this manual. After unpacking the device please keep the
package and technical description. Warranties are canceled in case the device was not
transported in the original package or maintenance procedures were violated.
Manufacturer is not responsible for device disfunction as a result of improper
maintenance, storage and transportation including mechanical failures.
In case of device failure during the warranty period, customer has the right to repair it in
Service centre for free. The equipment is accepted for warranty repair clean from dust
and mud.
Cleaning equipment from dust and mud is not included in the warranty and is charged
separately.
Warranty service does not include training of equipment maintenance, as well other
service for providing functioning of device (connection, testing, customizing, preventive
works etc.), which customer can commit on his own according to the attached manual.
Producer is entitled to introduce constructive and software changes, not described in the
current manual.
Warranty service is not available in the following cases:
- Absence of warranty coupon, incorrectly filled warranty coupon, or corrected coupon
- If operation rules mentioned in the manual were violated.
- If there are mechanic damages of equipment.
- If there are foreign objects or liquid inside device.
The present warranty is not applied to lamps, batteries, belts, network adaptors, power
unit, safety fuse, brushes, parts of the body of the product and any other parts which
have naturally limited period of service including failures caused by instability or power
supply failures. Replaced defective parts are to be considered property of our company.
The owner delivers faulty equipment to the service centre at his own expense.