Autex Acoustics Lattice Eclipse Configuration guide

Install Instructions | Lattice Eclipse
Lattice Install Instructions | Metric | R1-0 | Autex Industries Ltd © December 2020
Page 1 of 3
Fig. 6Fig. 5
Fig. 1 Fig. 2
Fig. 3
Fig. 8Fig. 7
8 1/4”
47”
19 1/2”19 1/2”
92 1/4”
27 1/2” 27 1/2”37 1/2”
90
1 x Lattice Baffles
4 x 1m Galvanised Cables
4 x Ceiling Mounts
4 x Cable Adjusters
Separate the ceiling mounts into their individual parts -
ceiling mounts (Fig. 5) and ceiling mount caps (Fig. 6).
Screw ceiling mounts (Fig. 5) to the ceiling substrate at
the marked centres (Step 1) with a fixingappropriate for
the substrate.
Screw assembled cables into the fixed ceiling mounts.
Decide which way up the Lattice will hang - convex
downorconvex up - and lay the rails outin their
correctorientation.
Finish one side by methodically inserting one of each
pair into place in order of decreasing size (Fig. 1).
Repeat for the other side (Fig. 2).
Sort the Lattice ‘fins’ into pairs, then into size
order: largest to smallest. Start by taking one of the
largest fins and slotting it into the centre slots in the ‘rails’.
Determine where you want the Lattice to hang (Fig. 3).
Mark the ceiling mountpoints as per the dotted lines.
Remove theround plugs in the pre-cut holes of each
Lattice rail.
*Speak to your Autex Account Manager for more information on setting the best suspension height for your application.
Lift the Latticeup to meet the cables threading the wires
through the plugs and into the cable adjuster.
adjustments to set correct, level height*. Once set,trim
excess wire, leaving 1.5” for seismic compliance.
When the Lattice is hung, use the adjuster to make minor
Thread the ceiling mount caps (Fig. 6) onto the
cables (Fig. 7).
Thread the cable adjuster onto cables (Fig. 8).
PACK CONTENTS
2.
4.
INSTALLATION
2.
1.
ASSEMBLY
1.
5.
3.

Install Instructions | Lattice Torus
Lattice Install Instructions | Metric | R1-0 | Autex Industries Ltd © December 2020
Page 2 of 3
57”
18”
18”
90°
19 1/2” 19 1/2”
Fig. 1
Fig. 2
Fig. 3
Fig. 8Fig. 7
Fig. 4
Fig. 6Fig. 5
When the Lattice is hung, use the adjuster to make minor
adjustments to set correct, level height*. Once set, trim
excess wire, leaving 1.5” for seismic compliance.
2 x Lattice Baffles
8 x 1m Galvanised Cables
8 x Ceiling Mounts
8 x Cable Adjusters
Start clipping the fins into the top ring as shown in
Fig. 1, 2 and 3 until complete.
Once all fins are clipped to the top ring, gently and
evenly press the bottom ring into position. Ensure
all joints are snug and carefully roll over so the
larger ring is on the top. Check again for any loose
connections, make sure the hooks on the fins have
clipped over the top ring.
Thread the ceiling mount caps (Fig. 6) onto the
cables (Fig. 7).
Thread the cable adjuster onto cables (Fig. 8).
Determine where you want the Lattice to hang (Fig. 4).
Mark the ceiling fixing points as per dotted lines.
Lift the Lattice up to meet the cables, thread the wires
through the holes in the top ring and insert into the cable
adjuster.
Screw assembled cables into the fixed ceiling mounts.
Separate the ceiling mounts into their individual parts -
ceiling mounts (Fig. 5) and ceiling mount caps (Fig. 6).
Screw ceiling mounts (Fig. 5) to the ceiling substrate at
the marked centres (Step 1) with a fixing appropriate for
the substrate.
*Speak to your Autex Account Manager for more information on setting the best suspension height for your application.
2.
1.
1.
2.
3.
4.
5.
PACK CONTENTS INSTALLATION
ASSEMBLY

Install Instructions | Lattice Trapezium
Lattice Install Instructions | Metric | R1-0 | Autex Industries Ltd © December 2020
Page 3 of 3
290 X–12mm
46 1/2”
27 1/2”
50”
93 3/4”
90°
Fig. 1
Fig. 4Fig. 3
Fig. 6Fig. 5
Screw assembled cables into the fixed ceiling mounts.
1 x Lattice Baffle
4 x 1m Galvanised Cables
4 x Ceiling Mounts
4 x Cable Adjusters
Determine where you want the Lattice to hang (Fig.1).
Mark the ceiling mount points as per the above diagram.
Remove the round plugs in the pre-cut holes of each
Lattice rail.
Separate the ceiling mounts into their individual parts -
ceiling mounts (Fig. 3) and ceiling mount caps (Fig. 4).
Screw ceiling mounts (Fig. 3) to the ceiling substrate at
the marked centres (Step 1) with a fixing appropriate for
the substrate.
Thread the ceiling mount caps (Fig. 4) onto the
cables (Fig. 5).
Thread the cable adjuster onto cables (Fig. 6).
Lift the Lattice up to meet the cables and thread the wires
through the plugs and into the cable adjuster.
When Lattice is hung, use the adjuster to make minor
adjustments to set correct, level height*. Once set, trim
excess wire, leaving 1.5” for seismic compliance.
Once all the fins are inserted into the rail, flip the
Lattice over 180°. Slide the remaining rail into the
slots on the fins; again ensuring the tabs on the fins
click into the groove on the rail.
Lay one rail on its edge with the long slots facing
up and methodically slot the fins into each slot on
the rail at 90 degrees. Make sure the tabs on the
fins click into the groove on the bottom of the rail.
*Speak to your Autex Account Manager for more information on setting the best suspension height for your application.
1.
2.
1.
2.
3.
4.
5.
PACK CONTENTS INSTALLATION
ASSEMBLY