PREMIER POLYSTEEL Champion 924-301 User manual

Part No. Description Qty.
642-013 Champion Table Top 6’ 1
622-013 Champion Seat/Back 6’ 2
634-010 Stands
(free standing)
2
634-013A Brace
(6’ free standing w/umbrella)
2
516-058 3/8” x 1-1/2” SS Hex Bolt 16
516-028 3/8” SS Nylock Nut 16
516-023 3/8” SS Washer 32
924-301
Assembly Instructions
1. Drill out holes.
2. Attach both stands to the inside of table support bar. (See photo above)
3. Attach the seats to the stands.
4. Attach the straight end of each brace to the table. (See photo above)
5. Attach bent end of both braces to the cross bar of each stand. (See photo above)
Periodic check of bolt tightness recommended.
•Attach both stands to the inside of table support bar
•Attach the straight end of each brace to the table.
•Attach bent end of both braces to the cross bar of each stand.
642-013 Top
622-013 Seat
634-010 Stand
634-013A Brace
In Accordance to California law: WARNING This product contains a chemical known to the State of
California to cause cancer and birth defects or other reproductive harm.

10"
72"
30" 62 1/2"
6 1/4"
10 3/8"
50 7/8"
20"
30 3/8"
10"
25"
10"
Ground Level
Concrete
X.01
924-302
6' Champion Double Pedestal Direct Bury Table
SHEET 1 OF 2 REV.
A
SIZE

3
2
1
4
5
Drill 2 holes in the ground per the drawing on page 1. 1.
Place the pedestals in the holes. 2.
Drill plastic out of the mounting holes on the pedestals, top and seats using a 7/16” dia. drill bit. 3.
Fasten the table top and seats to the pedestals, support and level table. Check height. 4.
When the table is level and secured, fill the holes with concrete to about 2” below ground level. 5.
6
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-013 Champion Table Top 6' 1
2 622-013 Champion Seat/Back 6' 2
3 632-200 2 Pedestal Direct Bury Stand 2
4 516-058 3/8"x1-1/2" SS Hex Bolt 12
5 516-023 3/8" SS Flat Washer 24
6 516-028 3/8" SS Nylock Nut 12
X.01
924-302
6' Champion Double Pedestal Direct Bury Table
SHEET 2 OF 2 REV.
A
SIZE
In Accordance to California law: WARNING This product contains a chemical known to the State of
California to cause cancer and birth defects or other reproductive harm.

30"
10"
62 1/2"
6 1/4"
72"
10"
50 3/4"
20"
30"
10" 10"
30"
52 1/2"
26 1/4" 26 1/4"
Ground Level
Concrete
X.01
924-306
6' Champion Multi-Pedestal Direct Bury
SHEET 1 OF 2 REV.
A
SIZE

3
4
2
15
67
Drill 6 holes in the ground per the drawing on page 1. 1.
Place the pedestals in the holes. 2.
Drill plastic out of the mounting holes on the pedestals, top and seats using a 7/16” dia. drill bit. 3.
Fasten the table top to the pedestals, support and level table top. Check height. 4.
Fasten the seats to the pedestals, support and level seats. Check height. 5.
When the seats and top are level and secured fill the holes with concrete to about 2” below 6.
ground level.
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-013 Champion Table Top 6' 1
2 622-013 Champion Seat/Back 6' 2
3 630-081 Seat Pedestal 4
4 630-080 Table Pedestal 2
5 516-058 3/8"x1-1/2" SS Hex Bolt 12
6 516-023 3/8" SS Flat Washer 24
7 516-028 3/8" SS Nylock Nut 12
X.01
924-306
6' Champion Multi-Pedestal Direct Bury
SHEET 2 OF 2 REV.
A
SIZE
In Accordance to California law: WARNING This product contains a chemical known to the State of California to cause cancer and birth defects or other
reproductive harm.

Part No.
Description Qty.
642-013A
6’ Champion Table 1Ped 1
622-013A
6’ Champion Seat 1 Ped 2
638-020
6” Pedestal DB 1
638-021
Seat Support Arm 2
638-022
Table Top Arm 1
638-025
Seat Arm 2
516-023
3/8” SS Flat Washer 40
516-028
3/8” SS Nylock Nut 20
516-059
3/8” x 2-1/2” SS Hex Head Bolt 12
516-058
3/8” x 1-1/2” SS Hex Head Bolt 8
516-051
1/2” x 9” SS Hex Bolt 4
516-036
1/2” SS Nylock Nut 4
516-027
1/2” SS Washer 1.25” OD 8
924-308
Table Top and Seats not shown.
638-021
638-022
638-020
Periodic check of bolt tightness recommended.
638-025

924-308 Single Pedestal Direct Bury 6’ Champion Table
1Bore a 12-14” diameter hole 36” into the ground.
2Place 4-6” of pea rock in the hole.
3Place center pedestal post into the hole.
4Drill out the holes in the center pedestal and the seat arm mounting plate with a 1/2” drill
bit.
5Drill out all other holes with a 7/16” drill bit.
6Bolt the seat arms to the center pedestal using four 1/2” x 9” stainless steel hex bolts,
eight 1/2” stainless steel washers and four 1/2” stainless steel nylock hex nuts.
7Bolt seat supports on to the seat arms using four 3/8”x2-1/2” stainless steel hex bolts,
eight stainless washers and four 3/8“ stainless steel nylock hex nuts.
8Bolt table top support on to the center pedestal post using four 3/8”x2-1/2” stainless steel
hex bolts, eight stainless steel washers and four stainless steel nylock hex nuts.
9Bolt the table top on to the table top support using four 3/8”x1-1/2” stainless steel hex
bolts, eight stainless steel washers and four stainless steel nylock hex nuts.
10 Bolt the seats on to the seat supports using two 3/8”x1-1/2” stainless steel hex bolts, four
stainless steel washers and two stainless steel nylock hex nuts.
11 Level table and adjust to desired height. Recommended height is 20” from the ground to
the top of the seats.
12 Fill hole with concrete no higher than ground level.
In Accordance to California law: WARNING This product contains a chemical known to the State of California to
cause cancer and birth defects or other reproductive harm.