Automationdirect.com Stride SE3 Series User manual

Front Panel LEDs
LED State Description
PWR On Power input 1 or 2 is connected and operational
Off Power input 1 and 2 are both inactive
Ethernet Port
LINK/ACT
On Indicates that there is a proper Ethernet connection (link) between the port and another
Ethernet device, but no communications activity is detected
Blinking Indicates that there is a proper Ethernet connection (link) between the port and another
Ethernet device, and that there is communications activity
Off
Indicates that there is not a proper Ethernet connection (link) between the port and another
Ethernet device. Make sure that each end of the cable has been plugged in securely.
1
www.AutomationDirect.com
1-800-633-0405
Stride® SE3 SEriES iP67 ratEd induStrial
unmanagEd EthErnEt SwitchES
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860, USA
®
General Specifications
Processing Type Store and forward
Devices Supported All IEEE 802.3 compliant devices are supported
MAC Addresses 1K
Memory Buffer 448Kbits
Packet Forwarding Rate 14.88 Kpps for Ethernet ports
148.8 Kpps for Fast Ethernet ports
Storage Temperature Range -40 to +85 °C (-40 to +185 °F)
Humidity (Non-Condensing) 5 to 95% RH
Environmental Air No corrosive gases permitted
Vibration, Shock & Freefall IEC60068-2-6, -27, -32
EMI Emissions FCC Part 15 Subpart B Class A, CE EN55032/EN61000-6-4 Class A
EMS
CE EN55035/EN61000-6-2 Class A: IEC61000-4-2 (ESD), IEC61000-4-3 (RS), IEC61000-
4-4 (EFT), IEC61000-4-5 (Surge), IEC61000-4-6 (CS), IEC61000-4-8 (Magnetic Field)
RoHS RoHS (Pb free) compliant
Packaging and Protection Plastic case, IP67
Agency Approvals FCC, CE, UL 61010-1, 61010-2-201
Note: dowNload user maNual se3-user-m from the Product maNuals
area of automatioNdirect.com for additioNal details.
Power Details
Power Connection Dual DC power inputs through M12 5-pin A-coded male connector
Input Voltage Class 2 power supply: 12–48 VDC redundant power inputs
Reverse Power Protection Yes
System Power Consumption 0.5 W
Relay Contact No
Stride SE3 Unmanaged IP67 Models
Part Number M12
10/100Tx Ethernet Ports
Operating
Temperature
SE3-SW5U-N67-T 5-40 to +75°C [-40 to 167°F]
M12 Ethernet Ports
10/100BaseT Ports M12, female, D-coding, 4-pin
Ethernet Compliance IEEE 802.3i, 802.3u, 802.3x for 10/100 Ethernet
Auto-Crossover Yes, allows you to use straight-through or crossover wired cables
Auto-Sensing Operation Yes, full and half duplex
Auto-Negotiating Speed Yes
Flow Control IEEE 802.3x flow control, back pressure flow control
Cable Requirements Twisted pair (Cat5e or better, shielded recommended)
Max. Cable Distance 100m [328ft]
Note: M12 caps need to be used on open (disconnected) ports.
Replacement caps (Part # ZP-JBH-CAP) are available from AutomationDirect.com
RoHS Compliant
RoHS

2
www.AutomationDirect.com
1-800-633-0405
Copyright 2023, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
Dimensions:
mm [inches]
8.8
0.35
35.0
1.38
158.9
6.26
191.2
7.53
12.3
0.48
12.3
0.48
47.8
1.88
12.8
0.50
37.2
1.46
215.8
8.50
30.0
1.18
44.6
1.76
25.0
0.98
16.1
0.64
25.0
0.98
2X
10.0
0.39
2X
5.0
0.20
203.8
8.02
25.0
0.98
4X
R2.5
0.10
8/14/2023
STRIDE INDUSTRIAL UNMANAGED ETHERNET SWITCH, 5 PORTS, (5) ETHERNET 10/100Base-T
(M12) PORTS(S), -40 to +75 DEG C, PLASTIC HOUSING, IP67, 35mm DIN RAIL OR PANEL MOUNT
mm
[inch]
UNLESS OTHERWISE
SPECIFIED UNITS ARE:
LATEST VERSION PART DIMENSIONS MAY DIFFER SLIGHTLY
DUE TO MANUFACTURER'S VARIANCES
NOT TO
SCALE
3rd
ANGLE
SE3-SW5U-N67-T
SHEET 1 OF 1
INCH UNITS USED FOR
PART DESIGN
1-800-633-0405
AutomationDirect.com
8.8
0.35
35.0
1.38
158.9
6.26
191.2
7.53
12.3
0.48
12.3
0.48
47.8
1.88
12.8
0.50
37.2
1.46
215.8
8.50
30.0
1.18
44.6
1.76
25.0
0.98
16.1
0.64
25.0
0.98
2X
10.0
0.39
2X
5.0
0.20
203.8
8.02
25.0
0.98
4X
R2.5
0.10
8/14/2023
STRIDE INDUSTRIAL UNMANAGED ETHERNET SWITCH, 5 PORTS, (5) ETHERNET 10/100Base-T
(M12) PORTS(S), -40 to +75 DEG C, PLASTIC HOUSING, IP67, 35mm DIN RAIL OR PANEL MOUNT
mm
[inch]
UNLESS OTHERWISE
SPECIFIED UNITS ARE:
LATEST VERSION PART DIMENSIONS MAY DIFFER SLIGHTLY
DUE TO MANUFACTURER'S VARIANCES
NOT TO
SCALE
3rd
ANGLE
SE3-SW5U-N67-T
SHEET 1 OF 1
INCH UNITS USED FOR
PART DESIGN
1-800-633-0405
AutomationDirect.com
Unit weight: 0.4 kg [0.88 lb]
Installation – DIN Rail Mounting:
Using the included DIN rail mounting bracket, the switch
can be snapped onto a standard 35 x 7.5 mm height DIN rail
(Standard: CENELEC EN50022)
To install the DIN rail mounting bracket, use
the included screws as shown in the figure
to the right.
After the DIN-Rail bracket is installed on the
rear of the switch, follow the steps below to
mount the switch:
1. Hook top back of unit over the DIN rail.
2. Push bottom back onto the DIN rail until
it snaps into place.
3. Check to ensure that the bracket is
mounted tightly to the rail.
To remove the switch from the DIN rail, push the unit down to free the
bracket from the bottom of the DIN rail, then reverse the above steps.
Panel mounting steps:
1. Prepare 2 screws formounting the switch to a wall.
(M3 or M4 screws are recommended.)
2. Locate two screw holes in the wall or panel based
on the positions of two screw holes on the mount-
ing brackets.
3. Insert the screws through the screw holes on the
switch and secure the switch to the panel.
Installation – Panel Mounting:
The switch is designed to be panel mounted vertically
or horizontally using the steps below.
Power Wiring:
The switch can be powered from the same DC source that is used to power
your other devices. To maintain the UL listing, this source must be a Class 2
power supply. A DC voltage in the range of 12–48 VDC needs to be applied
through an M12 connector as shown in the chart below. We recommend
grounding the switch to the panel or chassis ground using an M3 or M4 ground
screw and grounding wire, attached to either the top or bottom wall mounting
hole. To reduce down time resulting from powerloss, the switch can be
powered redundantly with a second power supply as shown in the chart below.
A recommended DC power supply is AutomationDirect.com part number
PSL-24-030.
Communication Ports Wiring:
Communication Port Pin Definitions
Pin MDI Signal
1Transmit Data + (TD+)
2Receive Data + (RD+)
3Transmit Data - (TD-)
4Receive Data - (RD-)
1
2
43
12
43
Power Port Pin Definitions
Pin Description
1Power Input 1 +
2Power Input 2 +
3Power Input 2 -
4Power Input 1 -
5Ground
12
43
1
2
34
55
Recommended Wire Size 24 – 18 AWG
Additional Help and Support
• For additional product support, specifications, and
installation, download User Manual SE3-USER-M from the
Product Manuals area of www.AutomationDirect.com.
• For additional technical support and questions, call our
Technical Support team @ 770-844-4200.