AutomationDirect DL205 User manual

LED Connector Module ZL-CM08L120
Cables and PLC I/O Modules
PLC I/O Module TypeCable TypePLC Type Connector Module Type
ZL-CM08L120
D2-08NA-1ZL-2CBL1DL205 ZL-CM08L120
WARNING : WIRE ONLY ACCORDING TO WIRING DIAGRAMS SHOWN BELOW TO
AVOID CAUSING DAMAGE TO THE PLC OR CONNECTOR MODULE. MATCH THE
CORRECT COMBINATION OF CABLE, PLC I/O MODULE, AND CONNECTOR MODULE AS SHOWN.
EXAMPLE CONNECT
A B
A1
-
C 01 2 3456
TYPE CONNECTION FOR SENSOR DC
CONFIGURATION NPN
A1A1 A1A1 A1 A1A1
A2A2A2 A2A2A2 A2A2
SENSOR DC
TYPE
AT1-AN-1A
SENSOR DC
TYPE
AT1-AP-1A
A1
-
TYPE CONNECTION FOR SENSOR DC
CONFIGURATION PNP
A1A1 A1A1 A1 A1A1
A2A2A2 A2A2A2 A2A2
C01 2345 6
BU
BN
BK
BU
BN
BK
TYPE TYPE
REV 1.1PAG. 1

ZL-CM08L120
A1A1
A2A2
C01 23456
Sensor
switch
normal open
Sensor
switch
normal close
TYPE CONNECTION FOR SWITCH DC
WITH A2 COMMON
A2A2A2 A2A2A2
A1A1A1A1 A1 A1A1A1A1A1A1A1 A1 A1
A1A1A1A1A1A1 A1 A1A1A1A1A1A1A1 A1 A1
C01 23456
Sensor
switch
normal open
Sensor
switch
normal close
TYPE CONNECTION FOR SWITCH DC
WITH A1 COMMON
FA2A2
A2A2A2 A2A2A2
A1A1
A2A2
C01 23456
Sensor
switch
normal open
Sensor
switch
normal close
TYPE CONNECTION FOR SWITCH AC
WITH A2 COMMON
A2A2A2 A2A2A2
A1A1A1A1 A1 A1A1A1A1A1A1A1 A1 A1 A1A1A1A1A1A1 A1 A1A1A1A1A1A1A1 A1 A1
C01 23456
Sensor
switch
normal open
Sensor
switch
normal close
TYPE CONNECTION FOR SWITCH AC
WITH A1 COMMON
FA2A2A2A2A2 A2A2A2
A1
-
C01 23456
SENSOR AC
TYPE
VM1-A0-1B
TYPE CONNECTION FOR SENSOR AC
WITH A1 COMMON
A1A1 A1A1 A1 A1A1
A2A2A2 A2A2A2 A2A2
A1
-
TYPE CONNECTION FOR SENSOR AC
WITH A2 COMMON
SENSOR AC
TYPE
VM1-A0-1B
A1A1 A1A1 A1 A1A1
A2A2A2 A2 A2A2 A2A2
C01 23456
G H
E F
C D
BU
BN
BU
BN
TYPE TYPE
TYPE TYPE
TYPE TYPE
REV 1.1PAG. 2

Wiring Diagram power supply and cable
ZL-CM08L120
Cable ZL-2CBL1
ZL-CM08L120
110Vac
I/O Module Input Octal Address 0 corresponds to LED 0
A1 A1 A1 A1 A1 A1 A1 A1
A2 A2 A2 A2 A2 A2 A2 A2
I/O Module Input Octal Address 1 corresponds to LED 1
I/O Module Input Octal Address 2 corresponds to LED 2
I/O Module Input Octal Address 3 corresponds to LED 3
I/O Module Input Octal Address 4 corresponds to LED 4
I/O Module Input Octal Address 5 corresponds to LED 5
I/O Module Input Octal Address 6 corresponds to LED 6
I/O Module Input Octal Address 7 corresponds to LED 7
A1 A2
C0 1 2 345 6 7
Warning :
It is recommended to install
a 2 Amp fast blow fuse in series with
the power supply as an extra safety
measure.
Use a fuse terminal block such
as a DINnector DN-F10 or DN-F10L
COMPATIBLE WITH CONNECTION:
TYPE: TYPE:TYPE: TYPE:
EF GH
PLC DL 205 Type D2-08NA-1
AC Input I/O Module
REV 1.1PAG. 3