Go Power GP-DC Kit 1 User manual

Technical Support: [e-mail]
53498_MAN_GP-DC_Install_Kit_vI
Go Power! DC Install Kit
Owner’s Manual
1. Warnings
Avoid all electrical hazards. Disconnect batteries and electrical system from 120/240
VAC, or any other power source of electrical power, before attempting to install your Go
Power! GP-DC Install Kit.
Observe proper polarity throughout the installation process.
Work safely. Do not wear jewelry when working with electrical or mechanical equipment.
Use protective eyewear, gloves and apron when working with batteries.
Follow the safety precautionsof the battery manufacturer. Do not produce sparks when
working in locations where flammable gases or vapors exist. Shield skin and eyes from
battery acid. If skin, eyes or clothing comes in contact with acid rinse thoroughly with
water.
Avoid electrical shock. Make sure all sources (inverter, shore power, generator) are
disconnected.
2. Installation Overview
Congratulations on becoming the owner of a GP–DC Kit. Please read and understand all
instructions before installing your new product for the easiest and safest installation.
Before installing kit, review the installation design with this DC kit Installation Manual.
Contact your Authorized Go Power! Dealer if in doubt as to this kit's suitability or
compatibility with your system. Retain this guide for future reference.
2.1 Disclaimer of Liability & Warranty
The conditions or methods of installation, operation, use and maintenance of this kit and
its solar module are beyond the control of Go Power!. Go Power! does not assume
responsibility and expressly disclaims liability for loss, damage, or expense arising from,
or in any way connected with such installation, operation, use, or maintenance. Go
Power! does not cover labor or shipping for items returned.
3. Installation
1. The inverter fuse is to be mounted on the positive cable near the battery.
2. Kits 2 – 5 only: Cut the positive (red) cable according to desired location. Strip ½” to
¾” of insulation from the cables, and connect the fuse block as shown.

gp
electric.com
Go Power! DC Install Kit
Owner’s Manual
3. Kits 2 – 5 only: Tighten the lugs to 10 ft. lbs.
4. Observe the polarity of the cables (red = positive) (black = negative) and connect
accordingly to the inverter.
3.1 Installation Diagram (Kits 2 – 5 shown)
4. Specifications
Kit 1 Kit 2 Kit 3 Kit 4 Kit 5
Fuse Size 60 amp fuse 110 amp fuse 200 amp fuse 300 amp fuse 400 amp fuse
Cable GaugeIC #6 – 10 ft. IC #4 – 10 ft. IC #2 – 10 ft. IC 2/0 – 10 ft. IC 4/0 – 10 ft.
Inverter24 volt 12 volt 12 volt 12 volt 12 volt
100-400 watt 600-1000 watt 1100-1800 watt 2000-2500 watt 2600-3000 watt
24 volt 24 volt 24 volt 24 volt 24 volt
100-600 watt 600-1800 watt 2000-3000 watt 3100-4000 watt 4100-6000 watt
Go Power! GP-ISW200-12 GP-1000, GP-SW600, GP1750, GP-SW2000-12 GP-SW3000-12
Quick CheckGP-ISW200-24 GP-SW1000, GP-SW1500-12 GP2500
GP-ISW400-12 GP-SW1500-24 GP-SW2000-24
GP-ISW400-24 GP-SW3000-24
Included Items Inline Fuse 60, Fuse Block 110, Fuse Block 200, Fuse Block 300, Fuse Block 400,
10ft. 6awg Cables, 10ft. 4awg Cables, 10ft. 2awg cables, 10ft. 2/0awg cables, 10ft. 4/0awg cables,
11” Cable Ties, 11” Cable Ties, 11” Cable Ties, 11” Cable Ties, 11” Cable Ties,
5/16” Cable Clamps, 3/8” Cable Clamps, 1/2” Cable Clamps, 5/8” Cable Clamps, 3/4” Cable clamps,
#10x3/4” Screws #10x3/4” Screws #10x3/4” Screws #10x3/4” Screws #10x3/4” Screws
GP Inverter
Battery
Fuse Block
3
2
1
-
+
Technical Support: [e-mail]
53498_MAN_GP-DC_Install_Kit_vI