AutomationDirect CLICK C0-08TR-3 User manual

CLK-1
1-800-633-0405
CLICK Module Insert
www.automationdirect.com/click-plc
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860
C0-08TR-3 CLICK Expansion I/O Module
Copyright© 2020, Automationdirect.com Incorporated/All Rights Reserved Worldwide
C0-08TR-3
Please read and understand the information in this
insert prior to installation, operation, or servicing
this equipment. Please refer to the CLICK User
Manual (C0-USER-M) for more information
(https://cdn.automationdirect.com/static/manuals/
c0userm/c0userm.html).
General Specifications+
Operating Temperature 32° to 131°F (0° to 55°C)
Storage Temperature -4° to 158°F (-20° to 70°C)
Relative Humidity 30% to 95% (non-condensing)
Environmental Air No corrosive gases permitted (Level 2 environmental pollution)*
Altitude Up to 2000m
Agency Approvals
UL61010-2-201
CE (EN61131-2):2007*
RoHS (2011/65/EU) and amendment (EU) 2015/863
Output Specifications
Outputs per Module
8
Peak Voltage
30VDC; 264VAC
Operating Voltage Range
6–27 VDC;6–240 VAC
Output type
8 Relays, FORM A (SPST)
AC Frequency
47–63 Hz
Maximum Output Current
3A / point
6A / common
Minimum Load Current
5mA @ 5VDC
Maximum Inrush Current
5A for 10ms
OFF to ON Response
< 15ms
ON to OFF Response
< 15ms
Status Indicators
Logic Side (8 points, red LED)
Power Indicator (green LED)
Commons
4 (2 point / common)
Bus Power Required (24V)
Max. 90mA (all points ON)
+ Keep out iron powder, moisture, oil or chemicals. Isolate from shock or vibration, direct sunlight, and from electric or ferromagnetic eld.
* Meets EMC and Safety requirements. See the Declaration of Compliance for details.
WARNING
• Don’t use this equipment in a flammable or explosive environment in order to avoid accidental injury or fire.
• You should use external electromechanical devices that are independent of the PLC (Programmable Logic
Controller) system to provide protection for any part of the system. Otherwise, malfunction or output
failures may result in a hazardous accident.
• When using this product, connect it to the Click CPU unit.
• Please make sure that you earth the Ground terminal of the Power Units for CLICK CPU
(C0-00AC/01AC) to avoid electric shock or equipment damage during a short circuit.
• Don’t operate the equipment with a nonconforming external power supply to avoid electric shock,
equipment damage or fire.
• Don’t intentionally fault wiring; this may cause equipment damage or fire.
• To avoid electric shock or malfunctions which might result in an accident, don’t touch any terminal while
the PLC power is on.
• Don’t put metals (e.g. Screwdriver) into radiator holes, drop trash, or foreign objects (e.g. cut-off wire) into
the device, in order to avoid electric shock or equipment damage.
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the
equipment may be impaired.
CAUTION
• Use and store the equipment in an environment described in the specifications (regarding temperature,
humidity, vibrations, shock, etc.) in order to avoid equipment damage or fire.
• Ensure all wiring has strain reliefs in order to avoid damage to insulation which might result in electric shock
or fire.
• Ensure secondary external power circuits are only live after PLC control program is started. Otherwise a
malfunction or output failure may result in a hazardous accident.
• Don’t block the radiator holes. This may cause an increase of internal temperature resulting in equipment
damage or fire.
• Don’t disassemble or modify the equipment so as to avoid electric shock, equipment damage or fire.
• Cut off all phases of the external power source before maintenance work, thus avoiding electric shock or
equipment damage.
General Safety
Please follow the instructions below for personal and operational safety.
In this Insert Sheet, the safety instruction levels are classified into “WARNING” and “CAUTION”
Assumes that incorrect handling may cause hazardous conditions, resulting in
severe injury or death.
Assumes that incorrect handling may cause hazardous conditions, resulting in
medium or slight injury, or may cause equipment damage.
WARNING
CAUTION

CLK-2
1-800-633-0405
CLICK Module Insert
www.automationdirect.com/click-plc
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860
C0-08TR-3 CLICK Expansion I/O Module
Copyright© 2020, Automationdirect.com Incorporated/All Rights Reserved Worldwide
Installation and Mounting
Safety Installation
Please heed the following instructions when
installing:
• Mount the CLICK PLC unit horizontally to provide
proper ventilation.
• Do not mount the CLICK PLC unit upside down, on
a horizontal surface, or in a vertical arrangement.
• There is a minimum clearance requirement of 2in.
(51mm) from all sides of the cabinet and the equipment.
• There is a minimum clearance requirement of 3in.
(76mm) from the wiring ducts and the equipment.
• Please use this product in a metal enclosure/cabinet.
Installing Expansion I/O Modules:
• R emove protective cover over buss port.
• Push the LOCK slide (top and bottom of modules) to “UNLOCK”.
• Align module pins and tabs (attachment of modules) into adjacent
slots and firmly push together.
• Push the LOCK slides to “LOCK” to lock modules rigidly together.
Additional Help and Support
• For additional technical support and questions, call our
Technical Support team @ 1-800-633-0405 or 770-844-4200
Air
Flow
TX2
PORT2
PORT1
RX2
RX1 TX1
PWR
ERR RUN
STOP
RUN
To remove an I/O module, first disconnect all phases of external
power source and wait 5 seconds before installing or removing the
expansion I/O module of a functioning system.
Then push LOCK slides to “UNLOCK” and gently separate modules.
1. Safety Installation, Wiring or Handling
• Discharge static electricity before installation or wir-
ing in order to avoid electric equipment damage.
2. Preface
• CLICK C0-08TR-3 is supported by CLICK Programming software Ver 2.60
or higher.
3. Compliant Crimp-type terminal
• I/O terminals
4. The following crimping ferrules are recommended for 24VDC
terminal and I/O terminals of CPU and Expansion I/O.
5. Safety Standard
• To comply with safety standards, please observe and use the following:
Please use SELV (as defined by UL61010-2-201) and Limited Energy (as
defined by UL61010-1, 9.4)
Please ensure basic insulation is provided between each relay block.
In order to comply with IEC/UL 61010-2-201 if the output is connected
to a circuit lower than 30V, please provide an external isolation before
the relay output terminals. Basic isolation requires an air separation of at
least 1.5 mm, a creepage distance of at least 2.5 mm, and a withstand
voltage of 1500V rms.
Enclosures
It is important to select the appropriate enclosure to ensure safe and proper oper-
ation of your CLICK PLC system. Control applications vary and yours may require
additional considerations. At a minimum your enclosure should include:
• Conformance to electrical standards
• Protection from the elements in an industrial environment
• Common ground reference
• Maintenance of specified ambient temperature
• Access to equipment
• Security or restricted access
• Sufficient space for proper installation and maintenance of equipment
CAUTION
• When installing modules and CPU on DIN rails, always
use end brackets on both ends of assembly.
• You should use 35mm width DIN Rails.
• You should use M4 size screws when you surface mount.
• You should tighten the screws with a spring washer and
a small round washer and torque (0.5 to 0.6 N·m).
CAUTION
Do not operate without first installing safety cover over power supply leads.
Company Series Model No. Compliant Wire
Zoller+Fröhlich Twin Ferrules V30AE001134 * 0.5 mm2
(20 AWG)
* Rated torque is 0.5 N·m. Take care not to contact adjacent terminal.
51mm
Minimum clearance requirement
of 51mm for A, B, and C.
1
2
3
Locking Tabs (Top and Bottom)
OPEN CLOSED
Modules easily connect to each other.

CLK-3
1-800-633-0405
CLICK Module Insert
www.automationdirect.com/click-plc
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860
C0-08TR-3 CLICK Expansion I/O Module
Copyright© 2020, Automationdirect.com Incorporated/All Rights Reserved Worldwide
24VDC 24V
Internal Module Circuitry
240VAC
OUTPUT
Load
COM
Equivalent Circuit Diagram:
Dimensional Drawings
Wiring Diagram:
12.0
0.47
75.0
2.95
44.3
1.74
40.7
1.60
13-WIRE CONNECTOR
85.0
3.35
8.5
0.33
37.0
1.46
Dimensions: mm
[inches]