AUVIO 3301089 User manual

THE PERFORMANCE YOU NEED
®
®
Wireless Stereo Headphones
Wireless Stereo Headphones
User’s Guide 3301089
Please read this user’s guide before using your new
headphones.

2
Package Contents
Stereo Headphones Docking Station
AC Adapter 3-foot (91.4cm) RCA Cable
1/8“ (3.5mm) Adapter 1/4“ (6.3mm) Adapter
User’s Guide
Features
Completely wireless, with a 115-foot (35m) range for use
virtually anywhere in your home
Powerful extended bass
Padded earcups and adjustable headband for comfort
Docking station charges the headphones when you use
rechargeable batteries (not included)
Engineered to reduce interference and disruptive noise
Connect the Docking Station
1. Connect the docking station to your audio source using the
included RCA cable, matching the colors to your output
jacks. If needed, use the included ¹/8“ or 1/4“ adapters.
2. For optical sources, use an optical cable (not included) to
connect the docking station to an external optical output
source such as a DVD player. Fiber optic input supports
PCM format only.
3. Connect the included AC adapter to the docking station
and plug into a standard power outlet.

3
Back View of Docking Station
Audio Out
1/8” Stereo
Headphone
Jack
¼” Stereo
Headphone
Jack
-or- -or-
-or-
UPDOWN
MULTIJOG
MASTER
VOLUME
ENTER
AUDIOMULTI- CHANNEL RECEIVER
SX-218
FRONT
AUDIOINPUT
DVD/LD TV/SAT DVR CD CD -R/TAPE/MD FRONTAUDIO FM AM
QUICK
SETUP SETUP RETURN
MUTE TONE
SLEEP
TUNER
EDIT
MULTIJOG
TUNING STATION MPX
VSB
MODE
DIALOGUE
ENHANCEMENT
Optical
On/Off
Source/Pair
Audio L/R
DC 5V

4
Volume +/–
Charging Connectors
Adjustable
Headband
Power
On/Off
Headphone LED
Lights blue when the headphone is turned on or paired.
Flashes blue rapidly when pairing. Flashes blue slowly if out of
range of docking station.
Lights red if E-Bass is active.
Flashes red slowly when the batteries are low.
Pair
E-Bass
Front View of Docking Station
Optical LED
Lights red when Optical
mode is selected.
O
p
tical
d.
Power LED
Lights green when the
docking station is turned on.
Slowly changes brightness
when charging rechargeable
batteries.
Lights green when fully
charged.
Pair LED
Flashes blue rapidly
when pairing.
Line In LED
Lights red when Line
In mode is selected.

5
Install Batteries
Note: When using rechargeable batteries, for best charging
performance use only NiMH batteries.
1. Slide open the L (LEFT)
battery compartment cover.
2. Switch ALK/RCH to ALK
for alkaline or RCH for
rechargeable batteries.
3. Insert two AAA alkaline
or rechargeable batteries
(neither included), matching
the polarity symbols
(+ and –) marked inside.
4. Replace the battery cover.
Warning: When using alkaline batteries, ALWAYS make sure you
adjust ALK/RCH to ALK. If set to RCH, the unit will try to charge the
batteries for a few seconds and the docking station’s Power LED will
flash rapidly before the unit stops charging. Attempting to recharge
alkaline batteries may cause the batteries to explode.
Battery Notes:
Dispose of old batteries promptly and properly. Do not burn or
bury them.
Use only fresh batteries of the required size and recommended
type. Do not mix old and new batteries of different sizes or types.
If you do not plan to use the headphones for an extended time,
remove the batteries. Batteries can leak chemicals that can
damage electronic parts.
When the headphone LED flashes red slowly, replace your
alkaline batteries or charge your rechargeable batteries.
ALK/RCH
AAA
AAA