AUVIO 4000334 User manual

THE PERFORMANCE YOU NEED
®
TM
40 W 2-Way
5.25’’ In-Ceiling Speaker
User’s Guide 4000334
Please read this user’s guide before using your new
speaker.

2
2
Package Contents
Speaker
Template/Paint mask
User’s Guide
Features
Mounts flush inside your ceiling for a sleek appearance
Two-way acoustic design provides great audio quality
from both ends of the sound spectrum
Spring-loaded terminals work with any standard
speaker wire
Foam edge forms a snug fit to reduce disruptive
vibrations
Grille and frame can be painted to match your decor
Easy to install using the included template
Required Tools
To mount your speaker, you need these tools
(not supplied):
Drywall or keyhole saw
Phillips screwdriver
18-20 gauge speaker wire
Wire stripper
Pencil or marker
1Prepare Speaker and Location
Be sure the mounting surface is:
between 2/5inch and 1 3/8inch (10 – 35 mm) thick.

3
3
has at least a 3 inch (76 mm) clearance behind the
mounting surface. Avoid wall studs or other objects that
might block the back of the speaker.
1. Remove the inner cardboard disc
from the supplied template/paint
mask and keep it for later. Use
the outer portion of the mask as a
template to mark the cutout hole
size and location for mounting the
speaker.
2. Use a drywall or keyhole saw to cut the hole.
(Optional) Paint the Grille
nNote: Do not paint internal speaker components. We
recommend you spray-paint the grille so no paint gets in or
blocks the holes.
1. Push any two opposite mounting
tabs and remove the grille.
2. Remove the dust cloth from behind
the grille.
3. Paint the grille and replace the dust
cloth after the paint is dry.
(Optional) Paint the Frame
To prevent paint from entering the
speaker, remove the grille and insert
the supplied cardboard paint mask.
After the paint is dry, remove the paint
mask and replace the grille.
Template
Paint mask
Mounting tab

4
4
2Connect Speaker Wires
Connect the speaker to your amplifier outputs, using wire
that is color-coded or otherwise marked to help connect the
wires correctly.
1. Turn off the amplifier and all associated equipment.
2. Route the speaker wire from the amplifier to the speaker.
3. Separate about 2 inches (50 mm)
of speaker wire at each end.
4. Using a wire stripper, remove
about ½ inch (13 mm) of insulation
from each wire and twist the
exposed ends.
5. Connect the positive marked
(usually red) wire to a red speaker
terminal by pressing the tab,
inserting the wire into the hole and releasing the tab.
Repeat this procedure for the negative marked wire
(usually black) and black terminal.
6. Connect the wire from the red speaker terminal to
the amplifier’s positive (+) terminal, then connect the
wire from the black speaker terminal to the amplifier’s
negative (–) terminal.
1/2’’
1/2’’
Strip insulation
Split wire
Amplifier
AM
LOOP
FM UNBAL
75
Ω
ANTENNA
FRONT
RLCENTERSURROUND
S
K
E
R
S
RL
S-VIDEO cable Coaxial digital cable
Composite Video Cables Audio Cables Component Video Cables
SPEAKERS

5
5
n Notes:
Make sure that the polarities and impedance of the
speaker and amplifier match.
Avoid routing the speaker wire near electrical wires.
Do not nail, staple, or otherwise puncture the speaker
wire.
Use a speaker wire no thicker than 14 gauge A.W.G.
and no longer than 30 ft to avoid signal loss in the cable.
3Mount the Speaker
1. Remove the grille to expose the mounting screws.
2. Turn in the mounting tabs, allowing the speaker to fit into
the mounting hole. Then insert the speaker into the hole.
3. Turn out the tabs and use the supplied screws to tighten
the speaker to the wall or ceiling. Be careful not to
overtighten.
4. Replace the grille.
nNote: When removing the speaker from the wall or
ceiling, loosen the screws just enough to remove the
speaker. This will prevent loss of the mounting tabs behind
your wall.

6
6
Maintenance
To avoid damaging the speaker, turn down the volume
of your amplifier before turning it on.
Do not use overrating power, which can damage sound
quality and loudspeaker drivers.
Clean your speaker with a soft cloth.
This speaker is not magnetically shielded. Placing it
near a TV set may magnetize the TV’s screen and cause
viewing issues.
Specifications
Power Handling .............................................. 20W RMS, 40W max.
Frequency Response ................................................... 65-20,000 Hz
Crossover frequency............................................................ 3500 Hz
Impedance ...............................................................8 ohms nominal
Sensitivity...................................................................87dB @ 1W/M
Woofer.....................................................................5.25-in (13.3 cm)
Tweeter ................................................................... 0.625-in (1.6 cm)
Cutout diameter .................................................... 6.5-in (165.1 mm)
Mounting depth.......................................................... 3-in (76.2 mm)
Specifications are subject to change and improvement without
notice. Actual product may vary from the images found in this
document.
Limited Warranty
Ignition L.P. warrants this product against defects in materials and
workmanship under normal use by the original purchaser for one (1) year
after the date of purchase. IGNITION L.P. MAKES NO OTHER EXPRESS
WARRANTIES.
This warranty does not cover: (a) damage or failure caused by or attributable
to abuse, misuse, failure to follow instructions, improper installation or
maintenance, alteration, accident, Acts of God (such as floods or lightning),
or excess voltage or current; (b) improper or incorrectly performed repairs by
persons who are not a Ignition L.P. Authorized Service Facility; (c) consum-
ables such as fuses or batteries; (d) ordinary wear and tear or cosmetic
damage; (e) transportation, shipping or insurance costs; (f) costs of product

7
7
removal, installation, set-up service, adjustment or reinstallation; and (g)
claims by persons other than the original purchaser.
Should a problem occur that is covered by this warranty, take the product
and the sales receipt as proof of purchase date to the place of purchase in
the U.S. Ignition L.P. will, at its option, unless otherwise provided by law: (a)
repair the product without charge for parts and labor; (b) replace the product
with the same or a comparable product; or (c) refund the purchase price.
All replaced parts and products, and products on which a refund is made,
become the property of Ignition L.P. New or reconditioned parts and products
may be used in the performance of warranty service. Repaired or replaced
parts and products are warranted for the remainder of the original warranty
period. You will be charged for repair or replacement of the product made
after the expiration of the warranty period.
IGNITION L.P. EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDI-
TIONS NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND, IF APPLICABLE, THE IMPLIED
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE
ON THE EXPIRATION OF THE STATED WARRANTY PERIOD.
EXCEPT AS DESCRIBED ABOVE, IGNITION L.P. SHALL HAVE NO LIABILITY
OR RESPONSIBILITY TO THE PURCHASER OF THE PRODUCT OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE
OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING
FROM INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY,
REVENUE, OR PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, EVEN IF IGNITION L.P. HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from
state to state. You may contact Ignition L.P. at:
Ignition L.P., 3102 Maple Ave., Suite 450, Dallas, TX 75201 02/09
For product support, call 1-866-315-0426

8
8
© 2010. Ignition L. P. All rights reserved. Auvio is a registered trademark used by
Ignition L.P. Package and insert are recyclable. Insert contains recycled material.
Protect the environment by recycling used electronics. Go to
E-CyclingCentral.com to find an electronic recycling center near you.
Get more from your audio and video equipment. See what
you’ve been missing. With Auvio, you control the experience.
Auvio was established by a group of technophiles to
provide high quality audio and video products without
the high sticker price. The Auvio philosophy is for you to
experience audio and video as it was intended to be: pure
and distortion free.
We know electronics can be intimidating. Auvio simplifies
your experience by providing the right products, with the
right specs, to work with your equipment.
Be confident about your purchase: your new Auvio product
incorporates the latest technology, is built to the highest
quality standards, and reduces environmental impact by
complying with RoHS environmental restrictions.
Printed
in China
09A10
4000334
Complies with the European Union’s “Restriction of Hazardous
Substances Directive,” which protects the environment by
restricting specific hazardous materials and products.