AV-Box TPUH632 User manual

TPUH632
18G HDMI Extender
All Rights Reserved
Version: TPUH632_2019V1.1
User Manual

18G HDMI Extender
2
Statement
Thanks for choosing this product, please read this user manual carefully before using
this product. The functions described in this version are updated till April, 2019. In the
constant effort to improve our product, we reserve the right to make functions or
parameters changes without notice or obligation.
Safety Precaution
Do not dismantle the housing or modify the module to avoid electrical shock or burn.
Using supplies not meeting the products' specifications may cause damage,
deterioration or malfunction.
Do not expose the unit to rain, moisture or install this product near water.
Install the device in a place with fine ventilation.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit.
Always unplug the power to the device before cleaning.
Unplug the power when not used for a long period of time.
Refer all servicing to qualified service personnel.
After-sales Service
We provide limited warranty for the product within three years.

18G HDMI Extender
3
Product Introduction
Thanks for choosing the 18G HDMI Extender which consists a transmitter and a
receiver. The extender adopts DSC compression technology to extend 4K@60Hz
4:4:4 HDMI video to distance up to 40 meters (131 feet) and 1080p@60Hz video to
distances up to 70 meters (230 feet) over a single CATx cable. It supports
bi-directional IR and RS232 pass-through to control source or display devices remotely.
It also supports CEC pass-through. Moreover, Power over HDBaseT (PoH) feature
allows the transmitter or receiver to be powered by each other over the CATx cable.
Features
Supports HDMI 2.0 and the HDMI video resolution up to 4K@60Hz 4:4:4, HDR.
Supports HDCP pass-through and up to HDCP 2.2 version.
Extends 4K@60Hz 4:4:4 signal up to 40m and 1080p@60Hz signal up to 70m via a
single CATx cable.
DSC (Display Stream Compression) technology.
Supports CEC pass-through.
Supports bi-directional IR, RS232 and 48V PoH.
Provides DIP switches for selecting RS232 pass-through mode or firmware upgrade
mode.
Packing List
1x Transmitter
1x Receiver
2x TX Mounting Ears with 2 Screws
2x RX Mounting Ears with 2 Screws
4x TX Plastic Cushions
4x RX Plastic Cushions
1x 3-pin Terminal Block
1x RS232 Cable (3-pin to DB9)
1x Power Adapter (DC 24V)
1x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

18G HDMI Extender
4
Transmitter Panel Description
1. Power LED: The LED illuminates green when power is applied and is off when no
power is present.
2. HDCP LED: The LED illuminates blue when there is HDMI video traffic with HDCP.
It will blink blue when there is HDMI video traffic without HDCP and will be off
when there is no HDMI video traffic.
3. Link LED: The LED illuminates blue when there is a valid HDBaseT connection
with the receiver. The LED is off when there is no valid link.
4. HDMI In LED: The LED illuminates blue when there is HDMI video input.
5. Switch for determining the behavior of the RS232 connection:
RS232: When in the position, it serves as an RS232 serial extension.
FW Update: When in the position, it allows you to update the firmware by
connecting to a PC and running the batch file. Please contact your distributor
for more details.
6. HDBT Out: RJ45 port to connect the HDBT In port of receiver by CATx cable.
The left HDCP LED illuminates green when the video contains HDCP content.
The right Link LED illuminates orange when there is a valid HDBaseT link
between the transmitter and the receiver.
7. HDMI In: Type-A female HDMI input port to connect an HDMI source device.
8. RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a
third-party device to be controlled.
9. IR In: 3.5mm mini jack to connect IR receiver or IR system for IR pass-through.
10. IR Out: 3.5mm mini jack to connect IR emitter for IR pass-through.
11. DC 24V: Locking power port for 24V DC power adapter connection.
DC 24VHDBT Out HDMI In IR Out
IR InRxTx
HDMI InLink
HDCP
RS232
FW Update
12345678910 11

18G HDMI Extender
5
Receiver Panel Description
1. Power LED: The LED illuminates green when power is applied and is off when no
power is present.
2. HDCP LED: The LED illuminates blue when there is HDMI video traffic with HDCP.
It will blink blue when there is HDMI video traffic without HDCP and will be off
when there is no HDMI video traffic.
3. Link LED: The LED illuminates blue when there is a valid HDBaseT connection
with the transmitter. The LED is off when there is no valid link.
4. HDMI Out LED: The LED illuminates blue when there is HDMI video output.
5. Switch for determining the behavior of the RS232 connection:
RS232: When in the position, it serves as an RS232 serial extension.
FW Update: When in the position, it allows you to update the firmware by
connecting to a PC and running the batch file. Please contact your distributor
for more details.
6. HDBT In: RJ45 port to connect the HDBT Out port of transmitter by CATx cable.
The left HDCP LED illuminates green when the video contains HDCP content.
The right Link LED illuminates orange when there is a valid HDBaseT link
between the transmitter and the receiver.
7. HDMI Out: Type-A female HDMI output port to connect an HDMI display device.
8. RS232: 3-pin terminal block to connect the RS232 control device (e.g. PC) or a
third-party device to be controlled.
9. IR In: 3.5mm mini jack to connect IR receiver or IR system for IR pass-through.
10. IR Out: 3.5mm mini jack to connect IR emitter for IR pass-through.
11. DC 24V: Locking power port for 24V DC power adapter connection.
DC 24VHDBT I HDMI Out IR Out
IR InRxTx
Link
HDCP
RS232
FW Update
HDMI Out
12345678910 11

18G HDMI Extender
6
Technical Specification
TPUH632T
Input
(1) HDMI
Input Connector
(1) Type-A female HDMI
Output
(1) HDBT
Output Connector
(1) RJ45
Control
(1) RS232, (1) IR In (1) IR Out,
Control Connector
(1) 3-pin terminal block, (2) 3.5mm mini jacks
TPUH632R
Input
(1) HDBT
Input Connector
(1) RJ45
Output
(1) HDMI
Output Connector
(1) Type-A female HDMI
Control
(1) RS232, (1) IR In (1) IR Out,
Control Connector
(1) 3-pin terminal block, (2) 3.5mm mini jacks,
General
Video Resolution
Up to 4K@60Hz 4:4:4, HDR
HDMI Audio Format
LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, Dolby Digital® Plus,
DTS:X™, and DTS-HD® Master Audio™ pass-through.
Bandwidth
18Gbps
HDMI Standard
2.0
HDCP Version
2.2, 1.4 compliant. Pass-through
CEC
Pass-through
EDID
Pass-through
Bidirectional PoH
Supported
Transmission Standard
HDBaseT
Transmission Distance
4K@60Hz 4:4:4 ≤ 40 meters (131 feet),
1080p@60Hz ≤ 70 meters (230 feet)
Operation Temperature
-5~ +55℃
Storage Temperature
-25 ~ +70℃
Relative Humidity
10%-90%
Power Supply
Input:100V~240V AC; Output: 24V DC 1.25A
Power Consumption
15W (Max)
Dimension (W*H*D)
TX/RX: 110mm x 20mm x 145mm
Net weight
TX/RX: 380g

18G HDMI Extender
7
System Connection
The following diagram illustrates the typical input and output connection of the
extender:
Transmitter
IR Emitter
4K Blu-Ray Laptop
TV Remote
IR Recevier
Receiver
IR Emitter
HDTV
Blu-Ray
Remote
IR Receiver
HDMI:
IR:
RS232:
CATx:
Power:
PoH
4K 40m,1080P 70m