Avalue Technology EMX-B75 User manual

Part No. E2017B75M00R
EMX-B75
Intel® Core™ i7/ i5/ i3/ Pentium®/ Celeron® Mini ITX
Motherboard with Intel® B75 Chipset
Quick Installation Guide
4th Ed –13 September 2013

EMX-B75 Quick Installation Guide
2 EMX-B75 Quick Installation Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2013 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
A Message to the customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.

EMX-B75 Quick Installation Guide
EMX-B75 Quick Installation Guide 3
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/
Headquarters and Branch
Avalue Technology Inc.
7F, 228, Lian-cheng Road, Zhonghe Dist., New Taipei City 235, Taiwan
Tel: [phone] Fax: [phone]
Information: [e-mail] Service: [e-mail]
Avalue USA
Avalue Europe
Avalue Technology Inc.
9 Timber Lane, Marlboro, NJ 07746-1443
Tel: [phone]
Fax: [phone]
Information: [e-mail]
Service: [e-mail]
Avalue Europe A/S
Moelledalen 22C, 3140
Aalsgaarde, Denmark
Tel: [phone]
Fax:[phone]
Information: sales.e[email protected].tw
Service: service.europ[email protected].tw
BCM Advanced Research
Avalue China
BCM Advanced Research
an Avalue Company
7 Marconi, Irvine, CA92618
Tel: [phone]
Fax: [phone]
Information: [e-mail]
Web: www.bcmcom.com
Avalue Technology Inc.
Room 805, Building 9,No.99 Tianzhou Rd.,
Caohejing Development Area,
Xuhui District, Shanghai
Tel: [phone]
Fax:[phone]
Information: sales.c[email protected].cn
Service: [e-mail]

EMX-B75 Quick Installation Guide
4 EMX-B75 Quick Installation Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
Always note that improper disassembling action could cause damage to the
motherboard. We suggest not removing the heatsink without correct
instructions in any circumstance. If you really have to do this, please contact
us for further support.
1.2 Packing List
Before you begin installing your single board, please make sure that the
following materials have been shipped:
Quick Installation Guide X 1
Driver/Utility CD X 1
Serial ATA Signal Cable X 1
IO Shield
COM Cable X 1
VGA Cable X 1
Screw X 2
Motherboard X 1

EMX-B75 Quick Installation Guide
EMX-B75 Quick Installation Guide 5
2.Hardware
Configuration

EMX-B75 Quick Installation Guide
6 EMX-B75 Quick Installation Guide
2.1 Product Overview

EMX-B75 Quick Installation Guide
EMX-B75 Quick Installation Guide 7
2.2 Jumper and Connector List
You can configure your board to match the needs of your application by setting jumpers. A
jumper is the simplest kind of electric switch.
It consists of two metal pins and a small metal clip (often protected by a plastic cover) that
slides over the pins to connect them. To “close” a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1,
2, and 3. In this case, you would connect either two pins.
The jumper settings are schematically depicted in this manual as follows:
A pair of needle-nose pliers may be helpful when working with jumpers.
Connectors on the board are linked to external devices such as hard disk drives, a
keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to
configure your system to suit your application.
If you have any doubts about the best hardware configuration for your application, contact
your local distributor or sales representative before you make any changes.
The following tables list the function of each of the board’s jumpers and connectors.
Jumpers
Label
Function
Note
JS1/JS2
mSATA/Mini PCIe function Jumper
3 x 1 header, pitch 2.00 mm
JBAT
Clear CMOS
3 x 1 header, pitch 2.00 mm
JME
ME update
2 x 1 header, pitch 2.00 mm
JC11/31/41/51/61
Serial port 1/3/4/5/6 –Normal, 5V,12V
PIN 9 selector
3 x 2 header, pitch 2.00 mm
JRS_1
Serial port 2 in RS-422-485 mode
3 x 1 header, pitch 2.00 mm
JRS_2
Serial port 10 in RS-422-485 mode
3 x 1 header, pitch 2.00 mm
JKB_MS
PS/2 keyboard & mouse connector
5 x 2 header, pitch 2.54 mm
JKB
Keyboard power select jumper
3 x 1 header, pitch 2.00 mm
JDIMM
DDR3L using
2 x 1 header, pitch 2.00 mm

EMX-B75 Quick Installation Guide
8 EMX-B75 Quick Installation Guide
Connectors
Label
Function
Note
ATXPWR1
ATX Power Input Connector
10 x 2 header, pitch 4.20 mm
PWR12V
Power connector
2 x 2 wafer, pitch 4.20 mm
FPANEL
Front Panel Switches
8 x 2 header, pitch 2.54 mm
JSPDIF1
Sony/Philips Digital Interface
3 x 1 header, pitch 2.54 mm
JLPT
Printer
2 x 13 header, pitch 2.54 mm
HDMI
HDMI connector
DVI-D
DVI-D connector
F_AUDIO
Front Panel Audio Connection Header
2 x 5 header, pitch 2.54 mm
AUDIO
Audio connector
COM1_3
Serial port 1_3 connector
COM2/10
Serial port 2/10 connector
4 x 1 header, pitch 2.54 mm
COM4~9
Serial port 4~9 connector
5 x 2 header, pitch 2.00 mm
JGPIO1
General Purpose I/O
6 x 2 header, pitch 2.54 mm
USBLANA/B
USB and RJ45LAN Connector A/B
PS/2
Keyboard and Mouse
F_USB1/2
USB Connector 1/2 - USB2.0
5 x 2 header, pitch 2.54 mm
F_USB3
USB Connector 3 - USB3.0
10 x 2 header, pitch 2.00 mm
SATA2~6
Serial ATA connector 2~6
SFAN1
System Fan connector
3 x 1 wafer, pitch 2.54 mm
CFAN1
CPU Fan connector
4 x 1 wafer, pitch 2.54 mm
JVGA
VGA connector
5 x 2 header, pitch 2.54 mm
MPCIE1
Mini-PCIe
DIMM1
DDR3 SODIMM connector1
DIMM2
DDR3 SODIMM connector2

EMX-B75 Quick Installation Guide
EMX-B75 Quick Installation Guide 9
2.3 Setting Jumpers & Connectors
2.3.1 mSATA/Mini PCIe function Jumper (JS1/JS2)
* Default
JS1
JS2
MPCIE* MSATA
Pin
Pin
Define
1-3
2-4
M-SATA
3-5
4-6
MINIPCIE
2.3.2 Clear CMOS (JBAT)
* Default
Normal*
Clear
Pin
Define
1-2
Normal
2-3
Clear
JS2
JS1

EMX-B75 Quick Installation Guide
10 EMX-B75 Quick Installation Guide
2.3.3 ME update (JME)
* Default
Refresh the ME*
Can’t refresh the ME
2.3.4 Serial port 1/3/4/5/6 –Normal, 5V, 12V PIN 9 selector (JC11/31/41/51/61)
* Default
Normal*
5V
12V
PIN
Define
1-2
Normal
3-4
5V
5-6
12V
JC11
JC31
JC41
JC51
JC61