Avalue Technology EMX-VX11P User manual

Part No. E2047VX1100R
EMX-VX11P
Onboard ZX-C Series Processor with VX11PH(PCH) Mini ITX
Motherboard
User’s Manual
1st Ed –19 November 2019

EMX-VX11P User’s Manual
2 EMX-VX11P User’s Manual
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2019 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that

User’s Manual
EMX-VX11P User’s Manual
3
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose
failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

EMX-VX11P User’s Manual
4 EMX-VX11P User’s Manual
Product Warranty
Avalue warrants to you, the original purchaser, that each of its products will be free from
defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Avalue, or which have been subject to
misuse, abuse, accident or improper installation. Avalue assumes no liability under the
terms of this warranty as a consequence of such events. Because of Avalue’s high
quality-control standards and rigorous testing, most of our customers never need to use our
repair service. If any of Avalue’s products is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will be billed according
to the cost of replacement materials, service time, and freight. Please consult your dealer
for more details. If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example,
CPU type and speed, Avalue’s products model name, hardware & BIOS
revision number, other hardware and software used, etc.) Note anything
abnormal and list any on-screen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information available.
3. If your product is diagnosed as defective, obtain an RMA (return material
authorization) number from your dealer. This allows us to process your good
return more quickly.
4. Carefully pack the defective product, a complete Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales
receipt) in a shippable container. A product returned without proof of the
purchase date is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it
prepaid to your dealer.

User’s Manual
EMX-VX11P User’s Manual
5
Content
1. Getting Started............................................................................................................8
1.1 Safety Precautions....................................................................................................8
1.2 Packing List...............................................................................................................8
1.3 Document Amendment History .................................................................................9
1.4 Manual Objectives...................................................................................................10
1.5 System Specifications.............................................................................................11
1.6 Architecture Overview—Block Diagram..................................................................15
2. Hardware Configuration...........................................................................................16
2.1 Product Overview....................................................................................................17
2.2 Jumper and Connector List.....................................................................................19
2.3 Setting Jumpers & Connectors ...............................................................................21
2.3.1 Serial port 1/2 pin9 signal select (JRI1/JRI2)................................................................................. 21
2.3.2 LVDS Back Light power selection (JSBKL1).................................................................................. 21
2.3.3 AT/ATX Power Mode Select (JSATX1).......................................................................................... 22
2.3.4 LCD Inverter connector (JBKL1).................................................................................................... 22
2.3.5 General purpose I/O connector (DIO1).......................................................................................... 23
2.3.6 Serial port 1 connector (COM1) ..................................................................................................... 23
2.3.7 Serial port 2 connector (COM2) ..................................................................................................... 24
2.3.8 Power connector (PWR1)............................................................................................................... 24
2.3.9 Serial Port 1/2 RS485/422 Mode connector (JRS485_1) .............................................................. 25
2.3.10 Serial Port 1/2 RS485/422 Mode connector (JRS485_2) ............................................................. 25
2.3.11 Serial port 3/4/5/6 connector (COM3/4/5/6) .................................................................................. 26
2.3.12 SATA Power connector 1 (SPWR1).............................................................................................. 27
2.3.13 USB connector 1 (JUSB1)............................................................................................................. 27
2.3.14 LPC connector (JLPC1)................................................................................................................. 28
2.3.15 Audio connector (FAUD1) ............................................................................................................. 28
2.3.16 LVDS connector (LVDS1).............................................................................................................. 29
2.3.17 EC Debug (JEC_PG1)................................................................................................................... 30
2.3.18 SPI connector (JSPI1)................................................................................................................... 30
2.3.19 Sony/Philips Digital Interface (SPDIF1)......................................................................................... 31
2.3.20 Miscellaneous setting connector 1 (FPT1).................................................................................... 31
2.3.21 Miscellaneous setting connector 2 (FPT2).................................................................................... 32
2.3.22 LED indicator connector 1 (LED1)................................................................................................. 32
2.3.23 LED indicator connector 2 (LED2)................................................................................................. 33
2.3.24 Speaker connector (SPK1)............................................................................................................ 33
2.3.25 JSMB connector (JSMB1)............................................................................................................. 34

EMX-VX11P User’s Manual
6 EMX-VX11P User’s Manual
2.3.26 PS2 keyboard/mouse connector (JKBMS).................................................................................... 34
2.3.27 Connector reserved for CH7511 FW flash jig (JROM).................................................................. 35
2.3.28 FAN connector (FAN1).................................................................................................................. 35
2.3.29 Battery connector (JBAT1)............................................................................................................ 36
2.3.30 Clear CMOS (JCOMS1) ................................................................................................................ 36
3.BIOS Setup....................................................................................................................37
3.1 Introduction .............................................................................................................38
3.2 Starting Setup .........................................................................................................38
3.3 Using Setup ............................................................................................................39
3.4 Getting Help............................................................................................................40
3.5In Case of Problems................................................................................................40
3.6 BIOS setup..............................................................................................................41
3.6.1 Main Menu...................................................................................................................................... 41
3.6.1.1 System Language.................................................................................................................. 41
3.6.1.2 System Date.......................................................................................................................... 41
3.6.1.3 System Time.......................................................................................................................... 41
3.6.2 Advanced Menu ............................................................................................................................. 42
3.6.2.1 APCI Settings ........................................................................................................................ 42
3.6.2.2 S5 RTC Wake Settings.......................................................................................................... 43
3.6.2.3 Trusted Computing................................................................................................................ 44
3.6.2.4 CPU Configuration................................................................................................................. 44
3.6.2.5 SATA Configuration............................................................................................................... 45
3.6.2.6 USB Configuration................................................................................................................. 46
3.6.2.7 H/W Monitor........................................................................................................................... 47
3.6.2.7.1 Smart Fan Mode Configuration ............................................................................................. 47
3.6.2.8 IT8528 Super IO Configuration.............................................................................................. 48
3.6.2.8.1 Serial Port 1 Configuration .................................................................................................... 49
3.6.2.8.2 Serial Port 2 Configuration .................................................................................................... 49
3.6.2.8.3 Serial Port 3 Configuration .................................................................................................... 50
3.6.2.8.4 Serial Port 4 Configuration .................................................................................................... 50
3.6.2.8.5 Serial Port 5 Configuration .................................................................................................... 51
3.6.2.8.6 Serial Port 6 Configuration .................................................................................................... 51
3.6.3 Chipset ........................................................................................................................................... 52
3.6.3.1 North Bridge........................................................................................................................... 52
3.6.3.1.1 Video Configuration............................................................................................................... 53
3.6.3.1.2 PCIE Configuration................................................................................................................ 54
3.6.3.2 South Bridge.......................................................................................................................... 55
3.6.3.2.1 USB Configuration................................................................................................................. 55
3.6.3.2.2 HDAC Configuration.............................................................................................................. 56
3.6.4 Boot................................................................................................................................................ 56

User’s Manual
EMX-VX11P User’s Manual
7
3.6.4.1 CSM16 Parameters............................................................................................................... 57
3.6.4.2 CSM Parameters................................................................................................................... 58
3.6.5 Security........................................................................................................................................... 59
3.6.5.1 Secure Boot menu................................................................................................................. 59
3.6.6 Save and exit................................................................................................................................ 60
3.6.6.1 Save Changes and Reset...................................................................................................... 61
3.6.6.2 Discard Changes and Reset.................................................................................................. 61
3.6.6.3 Restore Defaults.................................................................................................................... 61
3.6.6.4 Launch EFI Shell from filesystem device .............................................................................. 61
4. Drivers Installation.......................................................................................................62
4.1 Install Chipset Driver...............................................................................................63
4.2 Install VGA Driver....................................................................................................65
4.3 Install AHCI Driver...................................................................................................66
4.4 Install Audio Driver (For Realtek ALC892 HD Audio)..............................................68
4.5 Install LAN Driver....................................................................................................69
4.6 Install USB3.0 Driver...............................................................................................71
5. Mechanical Drawing ....................................................................................................73

EMX-VX11P User’s Manual
8 EMX-VX11P User’s Manual
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
Before you begin installing your single board, please make sure that the
following materials have been shipped:
1 x EMX-VX11P motherboard
1 x SATA power cable

User’s Manual
EMX-VX11P User’s Manual
9
1.3 Document Amendment History
Revision
Date
By
Comment
1st
November 2019
Avalue
Initial Release

EMX-VX11P User’s Manual
10 EMX-VX11P User’s Manual
1.4 Manual Objectives
This manual describes in details Avalue Technology EMX-VX11P Single Board.
We have tried to include as much information as possible but we have not duplicated
information that is provided in the standard IBM Technical References, unless it proved to
be necessary to aid in the understanding of this board.
We strongly recommend that you study this manual carefully before attempting to set up
EMX-VX11P or change the standard configurations. Whilst all the necessary information is
available in this manual we would recommend that unless you are confident, you contact
your supplier for guidance.
Please be aware that it is possible to create configurations within the CMOS RAM that
make booting impossible. If this should happen, clear the CMOS settings, (see the
description of the Jumper Settings for details).
If you have any suggestions or find any errors regarding this manual and want to inform us
of these, please contact our Customer Service department with the relevant details.

User’s Manual
EMX-VX11P User’s Manual
11
1.5 System Specifications
System
CPU
Onboard ZX-C+ Series CPU (Max TDP 18W)
BIOS
AMI uEFI BIOS, 64 Mbit SPI Flash ROM
System Chipset
VX11PH (PCH) (TDP 8.8W)
Co-lay VX11H (PCH) (TDP 5.8W) (GPU and power consumption difference)
I/O Chip
EC IT8528E
System Memory
1 x 204-pin DDR3 1333 MHz SO-DIMM supports up to 8GB
Watchdog Timer
H/W Reset, 1sec. –65535sec./min.1sec. or 1min. step
H/W Status
Monitor
CPU temperature monitoring
Voltages monitoring
CPU fan speed control
Expansion
1 x M.2 Type A 2230 support WiFi module ( 1 x PCI-e x 1 & USB 2.0 Signal)
(1 x PCI-e x 1 share with Gold Finger or IET) by BOM optional
M.2 Default disabled, no function.
1 x Full size Mini PCI-e (support mSATA/PCI-e x1/USB 2.0 Signal/SIM)
Default: Gold Finger supports
1 x USB2.0
1 x SATA
2 x PCI-e x1
OR by BOM optional
IET Support
1 x LPC
2 x PCI-e x1
2 x USB2.0
S3/S4
Yes (S0/S3/S4/S5)
I/O Specification
USB
3 x USB 3.0, 4 x USB 2.0
GPIO
16-bits GPIO
Display Specification
Chipset
VX11PH or VX11H Graphics
Resolution
1 x HDMI: 2K 2560 x 1440
1 x VGA: 2048 x 1536 @ 60Hz
Multiple Display
2
HDMI
1 x HDMI
VGA
1 x VGA
LCD Interface
1 x Dual channel 18/24-bits 1920x1080 LVDS (Chrontel CH7511B eDP to LVDS)

EMX-VX11P User’s Manual
12 EMX-VX11P User’s Manual
*F/W must be fine-tune by Avalue
Audio Specification
AC97 Codec
Realtek ALC662 HD Audio Decoding Controller
Audio Amp
Realtek ALC105 Stereo Class-D 3W x 2
Ethernet Specification
LAN Chip
2 x Intel® I210AT PCI-e Gigabit Ethernet
Ethernet
Interface
Gigabit Ethernet
Internal I/O Connectors
Fan
1 x 1 x 4 pin, pitch 2.54mm CPU fan connector with smart fan function supported
System 1 I2C
1 x 1 x 5 pin, pitch 2.00mm, +3.3S Level
Buzzer
Onboard
CMOS Battery
1 x horizontal type battery connector (Battery cable 170mm length)
Power ON
1 x 2 x 5 pin, pitch 2.54mm connector for front panel 1
1 x 2 x 5 pin, pitch 2.54mm connector for front panel 2
Audio
1 x 2 x 5 pin, pitch 2.54mm connector for front Audio
External I/O
Connector
Storage:
1 x Full size Mini PCI-e (support mSATA/PCI-e x1/USB 2.0 Signal/SIM)
1 x M.2 Type A 2230 support WiFi module (1 x PCI-e x 1 & USB 2.0 Signal) by BOM
optional
M.2 Default disabled, no function.
1 x SATA II
1 x SATA power connectors
COM:
COM 1 & COM2:
Support 422/485 selected by BIOS selection
2 x 2 x 3 pin, pitch 2.00mm connector, support RS422/485 connector, Pin 5 with +5V
COM 1~2
2 x 2 x 5 pin, pitch 2.00mm connector for COM1~2: support RS-232 connector, Pin 9
with / +5V & +12V Supported
COM 3~6
1 x 2 x 20 pin, pitch 2.00mm connector for COM 3~6 support RS-232 connector
COM 5~6
2 x 2 x 5 pin, pitch 2.54mm connector for 4 USB 2.0
+ 1 x 1 x 5, pitch 2.54mm connector for 1 USB 2.0 Type A Vertical connector
1 x 2 x 10 pin, pitch 2.00mm connector for GPIO: 16 bits & +3.3S Level SMBus
1 x 2 x 4 pin, pitch 2.00mm connector for PS2 KB/MS
1 x 2 x 4 pin, pitch 2.00mm connector for BIOS SPI
1 x 2 x 3 pin, pitch 2.00mm connector for EC SPI
1 x 2 x 5 pin, pitch 2.0mm connector for LPC debug.

User’s Manual
EMX-VX11P User’s Manual
13
1 x horizontal type battery connector (Battery cable 170mm length)
1 x 2 x 5 pin, pitch 2.54mm connector for front panel 1
1 x 2 x 5 pin, pitch 2.54mm connector for front panel 2
2 x 2 x 20 pin, pitch 1.25mm connector for LVDS (must be using WF40H6-7GAA178
connector)
2 x 1 x 5 pin, pitch 2.00mm Wafer connector for LCD inverter backlight connector
(5V/12V)
2 x 1 x 3 pin, pitch 2.54mm connector LCD backlight brightness adjustment
(PWM/DC)
1 x 2 x 5 pin, pitch 2.54mm connector for front Audio
1 x 4 pin, pitch wafer 2.00mm connector for 3W x 2 Speaker
1 x 3 pin, pitch 2.00mm connector for CMOS clear
1 x 1 x 4 pin, pitch 2.54mm CPU fan connector with smart fan function supported
2 x 1 x 4 pin, pitch 2.00mm connector for LAN Activity Indicator LED
1 x 2 x 2 pin, pitch 4.20mm connector for power input connector
1 x 1 x 3 pin, pitch 2.54mm connector for AT/ATX mode Fanless Operating
1 x 1 x 3 pin, pitch 2.54mm connector for SPDIF
Rear I/O Connectors
USB
3 x USB3.0 + 1 x USB 2.0
LAN
2 x Intel® I210AT PCI-e Gigabit Ethernet
HDMI
1 x HDMI
VGA
1 x VGA
Rear Side
External I/O
Connector
2 x RJ-45
3 x USB 3.0 + 1 x USB 2.0
1 x HDMI
1 x VGA
1 x Mic-In and 1 x Line-out
1 x DC Jack lockable connector type
Mechanical & Environmental
Power
Requirement
DC in +12V~24V
ACPI
Single power ATX Support S0, S3, S4, S5
ACPI 5.0 Compliant
Power Type
AT / ATX mode Switchable Through Jumper
Operating Temp.
0~60°C (32~140°F), with 0.5 m/s Air flow
Storage Temp.
-40~ +75°C
Operating
Humidity
40°C @ 95% Relative Humidity, Non-condensing
Size (L x W)
6.7" x 6.7" (170mm x 170mm)
Weight
0.40 kg

EMX-VX11P User’s Manual
14 EMX-VX11P User’s Manual
OS Support
Win7, Win10, Neokylin 7.0 64bit, kernel version 3.10.0-862.9.1nd7.zx.4.X86_64
Note:
1. Golden finger, M.2 and IET function:
a. 1 x M.2 Type A 2230 support WiFi module ( 1 x PCIe x 1 & USB 2.0 Signal) (1 x PCI-e x 1 share with
Gold Finger or IET) by BOM optional
M.2, IET connector default disabled, no function.
b. M.2 & mini-PCIE cannot work simultaneously.
If working simultaneously, one of them would shows！, which needs to be removed and reset.
2. EMX-VX11P limitation:
a. USB3.0 Port Performance around 3000Mb/S.
b. Chipset supports 4kx2k resolution, but by measurement can only show 1920 x 1080 resolution.
c. LVDS supports only three resolution: 1024x768, 1280x1024, 1920x1080
3. It is suggested to use Transcend DRAM for EMX-VX11P
4. NeoKylin :
a. NeoKylin Ubuntu 16.04 does not support ACPI S3 WakeUp, driver under chipset vendor development.
b. NeoKylin 7.0, 64 bit, kernel 3.10.0-862.9.1nd7.zx.4.X86_64 , LVDS no display, driver under chipset
vendor development.
5. Driver:
a. Using VGA Driver 10.18.16.0308 , VGA and HDMI would be “Extend display” automatically after
installation, user need to adjust it by control panel.
b. If user would like to design panel PC using EMX-VX11P board, we suggest to use VGA driver:
VX11_Win10x64 Graphics Driver 32-01-09 (Logo)
Please contact Avalue team.
c. For using INTEL AC7260 wifi module, user need to install Driver: 20.90.0, please contract Avalue team.
If using Intel website driver 21.10.1, the installation may not be completed.
6. EMX-VX11P standard package does not include heatsink; heatsink is optional for selling. Customer can
design own suitable heatsink or cooling solution.
And we suggest to add rubber on the bottom of board for system/panel PC design, to avoid board bend.
C4580/C4701 Processor operation is only guaranteed for a junction temperature of 90ºC.
7. If user need SMBUS, please contact Avalue team for NRE charge quotation.
8. Audio-out volume resulted from Realtek driver, and different under Win7 Win10 driver as below:
AMP Speaker 3W/4Ω, Correct Vrms around 3.46v
a. Win7+Audio Driver measure 2.6V
b. Win7 no Audio Driver measure 3.3V
c. Win10+Audio Driver measure 3.3V
PS: Win7+Audio measure 2.6V, which is already loud, if using Win7+Audio Driver or Win10+Audio
Driver for 3.3V, there may be concern to broken the speaker.

User’s Manual
EMX-VX11P User’s Manual
15
1.6 Architecture Overview—Block Diagram
The following block diagram shows the architecture and main components of EMX-VX11P.

EMX-VX11P User’s Manual
16 EMX-VX11P User’s Manual
2. Hardware
Configuration

User’s Manual
EMX-VX11P User’s Manual
17
2.1 Product Overview

EMX-VX11P User’s Manual
18 EMX-VX11P User’s Manual

User’s Manual
EMX-VX11P User’s Manual
19
2.2 Jumper and Connector List
You can configure your board to match the needs of your application by setting jumpers. A
jumper is the simplest kind of electric switch.
It consists of two metal pins and a small metal clip (often protected by a plastic cover) that
slides over the pins to connect them. To “close” a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1,
2, and 3. In this case, you would connect either two pins.
The jumper settings are schematically depicted in this manual as follows:
A pair of needle-nose pliers may be helpful when working with jumpers.
Connectors on the board are linked to external devices such as hard disk drives, a
keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to
configure your system to suit your application.
If you have any doubts about the best hardware configuration for your application, contact
your local distributor or sales representative before you make any changes.
The following tables list the function of each of the board’s jumpers and connectors.
Jumpers
Label
Function
Note
JRI1/2
Serial port 1/2 pin9 signal select
3 x 2 header, pitch 2.00mm
JSBKL1
LVDS Back Light power selection
3 x 1 header, pitch 2.00mm
JSATX1
AT/ATX Power Mode Select
3 x 1 header, pitch 2.54mm
Connectors
Label
Function
Note
FPT1
Miscellaneous setting connector 1
5 x 2 header, pitch 2.54mm
FPT2
Miscellaneous setting connector 2
5 x 2 header, pitch 2.54mm
DIMM1
206-pin DDR4 SO-DIMM socket
FAUD1
Front Audio connector
5 x 2 header, pitch 2.54mm
VGA
VGA connector
JBKL1
LCD Inverter connector
5 x 1 wafer, pitch 2.00mm

EMX-VX11P User’s Manual
20 EMX-VX11P User’s Manual
JSPI1
SPI connector
4 x 2 header, pitch 2.00mm
JEC_PG1
EC Debug
3 x 1 header, pitch 2.54mm
COM1
Serial Port 1 connector
5 x 2 header, pitch 2.00mm
COM2
Serial Port 2 connector
5 x 2 header, pitch 2.00mm
COM3-6
Serial Port 3/4/5/6 connector
20 x 2 header, pitch 2.00mm
DIO1
General purpose I/O connector
10 x 2 header, pitch 2.00mm
SPK1
Speaker connector
4 x 1 wafer, pitch 2.00mm
LVDS1
LVDS Connector
20 x 2 wafer, pitch 1.25mm
JUSB2
USB connector
JUSB3/4
USB connector 3/4
SPDIF1
Sony/Philips Digital Interface
3 x 1 header, pitch 2.54mm
LAN1/2
RJ-45 Ethernet 1/2
MPCIE
PCIe connector
LED1
LED indicator connector 1
4 x 1 header, pitch 2.00mm
LED2
LED indicator connector 2
4 x 1 header, pitch 2.00mm
JBAT1
Battery connector
2 x 1 wafer, pitch 1.25mm
JCOMS1
Clear CMOS
3 x 1 header, pitch 2.00mm
M2KA1
M.2 2230 Type A Slot (default no
function)
JUSB
USB connector
5 x 2 header, pitch 2.54mm
JRS485_1/2
Serial Port 1/2 RS485/422 Mode
connector
3 x 2 header, pitch 2.00mm
JLPC1
LPC connector
5 x 2 header, pitch 2.00mm
IET-CB1
IET Module connector (default no
function)
JSMB1
SMBus connector
5 x 1 header, pitch 2.00mm
JKBMS1
PS2 keyboard/mouse connector
4 x 2 header, pitch 2.00mm
FAN1
CPU fan connector
4 x 1 wafer, pitch 2.54mm
DCIN1
DC Power-in connector
PWR1
Power connector
2 x 2 wafer, pitch 4.20mm
SATA1/2
Serial ATA connector 1
SPWR1/2
SATA Power connector 1
4 x 1 wafer, pitch 2.54mm
HDMI1
HDMI connector
LOUT1
Line-out audio jack
MIC1
Mic-in audio jack
SIM1
SIM card slot