Avantco Equipment 184BT18H User manual

User Manual
www.AvantcoEquipment.com
09/2023
#184BT18A 120V • 1600W #184BT18H 208/240V • 2800/3200W
#184BT18AXL 120V • 1600W #184BT18HXL 208/240V • 2800/3200W
Standard Length Feed Tray:
Extended Length Feed Tray:
Vertical Contact
Bun Toasters
Please read and keep these instructions. Indoor use only.
Note:
Improper installation, adjustment, alteration, service, or
maintenance can cause property damage, injury, or death.
Read the installation, operating, and maintenance Instructions
thoroughly before installing or servicing this equipment.
Warning:
Do not store or use gasoline or other flammable vapors or
liquids in the vicinity of this or any other appliance.
For Your Safety:

User Manual
Vertical Contact Bun Toasters
2
www.AvantcoEquipment.com
Table of Contents
Safety Precautions .....................................................................................................................................3
Upon Arrival.................................................................................................................................................4
Installation ....................................................................................................................................................4
Operation .....................................................................................................................................................6
Cleaning & Maintenance..........................................................................................................................7
Troubleshooting .........................................................................................................................................8
CONFORMS TO NSF/ANSI STD. 4
CONFORMS TO UL STD. UL197
50097045009704
NEMA
5-15P
50097045009704
NEMA
6-20P
#184BT18A & #184BT18AXL
#184BT18H & #184BT18HXL

User Manual
Vertical Contact Bun Toasters
3
www.AvantcoEquipment.com
WARNING
• Read all instructions carefully and completely.
• For commercial use only.
• DO NOT touch hot surfaces.
• Protect against electrical shock by keeping all cords, plugs, and other electrical components away
from water or other liquids.
• Unplug this unit when not in use and before cleaning.
• Allow the unit to cool before putting on or taking o parts.
• DO NOT operate this or any appliance with a damaged electrical cord or plug.
• DO NOT operate this or any appliance after it has malfunctioned or has been damaged in any way.
• DO NOT use outdoors.
• DO NOT place on or near a hot gas or electric burner.
• Attach plug to appliance first, then plug electrical cord into the wall outlet.
• Disconnect the unit by removing the electrical plug from the wall outlet.
• DO NOT use appliance for any application other than intended use.
• DO NOT insert metal utensils or oversized foods into this unit, as they may cause a fire and increase
the risk of electrical shock.
• DO NOT store any item on top of this unit when in operation.
• DO NOT allow this toaster to touch or to be covered by flammable material, such as curtains,
draperies, walls, etc., when in operation.
• DO NOT clean with metal scouring pads, as pieces can break o and touch electrical components,
increasing the risk of electrical shock.
• Never place materials such as paper, cardboard, plastic, etc. in this toaster.
• DO NOT cover interior of this unit with metal foil, as it may cause the toaster to overheat.
• Avoid scratching the surface or nicking the edges of this unit. If the toaster is damaged or broken,
contact customer service before use.
• Turn o the appliance by removing the plug from the wall outlet.
• Note that the use of accessories not recommended by the manufacturer may result in injury.
• Children should be supervised to ensure that they DO NOT play with the toaster.
• This appliance is not intended for use by persons (including children) with reduced physical sensory
or mental capabilities, or lack of experience and knowledge, unless a person responsible for their
safety has given them supervision or instruction concerning use of the appliance.
• When using the appliance in shops, snack bars, hotels, etc., check the voltage and outlet to make
sure the appliance is correctly connected with power.
• Place unit on a flat surface that is well ventilated.
• The appliance must be supervised during operation.
• DO NOT leave appliance without powering o.
Safety Precautions

User Manual
Vertical Contact Bun Toasters
4
www.AvantcoEquipment.com
mv|-ѴѴ-ঞom
3.
0ĺ""+(+!"$$
_oѴ;vruob7;7ĺ$_;mb|1-m|_;m0;Ѵ;;ѴѴ;7vbm]|_;-7fv|-0Ѵ;r-u|o=|_;Ѵ;]ĺ
$Ĺ
$&$&"$$&")$&$$$"$ĺ
vo1h;|ĺ
0-1h-u7vĺ";;7b-]u-lĺ
];m|Ѵ|o;m]-];|_;7ub;];-uĺ";;7b-]u-lĺ
$Ĺ
!&"$$$$$(+!""$$ĺ$""$$"
(+$"!$$$$$"$!$$(
$$$$!(!"ĺ
|_-|ou7;uĺ
1
2
1
3
4
5
6
7
8
8
A.
B.
drive gear
cassette gear
$_;1-vv;;-vv;l0Ѵ_;b]_|0oѴ|bvru;v;|
=uol|_;=-1|ouĺ=|_;1-vv;;];-u7o;vmo|l-h;-7;t-|;1om|-1|ķoubv0bm7bm]b|_|_;
7ub;];-uķঞ]_|;mouѴoov;m|_;_;b]_|0oѴ||o;mvu;ruor;u1om|-1|ĺ
mv|-ѴѴ-ঞom
3.
0ĺ""+(+!"$$
_oѴ;vruob7;7ĺ$_;mb|1-m|_;m0;Ѵ;;ѴѴ;7vbm]|_;-7fv|-0Ѵ;r-u|o=|_;Ѵ;]ĺ
$Ĺ
$&$&"$$&")$&$$$"$ĺ
vo1h;|ĺ
0-1h-u7vĺ";;7b-]u-lĺ
];m|Ѵ|o;m]-];|_;7ub;];-uĺ";;7b-]u-lĺ
$Ĺ
!&"$$$$$(+!""$$ĺ$""$$"
(+$"!$$$$$"$!$$(
$$$$!(!"ĺ
|_-|ou7;uĺ
1
2
1
3
4
5
6
7
8
8
A.
B.
drive gear
cassette gear
$_;1-vv;;-vv;l0Ѵ_;b]_|0oѴ|bvru;v;|
=uol|_;=-1|ouĺ=|_;1-vv;;];-u7o;vmo|l-h;-7;t-|;1om|-1|ķoubv0bm7bm]b|_|_;
7ub;];-uķঞ]_|;mouѴoov;m|_;_;b]_|0oѴ||o;mvu;ruor;u1om|-1|ĺ
Upon Arrival
Installation
• Apparent damage or loss must be noted on the freight bill at the time of delivery. The carrier
representative (Driver) must sign the freight bill. If this is not done, the carrier may refuse the claim.
The carrier can supply the necessary forms.
• Concealed damage or loss if not apparent until after the toaster is removed from the carton, a request
for inspection must be made to the carrier within 15 days. The carrier should arrange an inspection.
Be sure to save all contents and packaging material.
Examine carton for damage. The freight carrier has assumed responsibility for its safe transit and delivery.
If equipment is received damaged, either apparent or concealed, a claim must be made with carrier.
The feed tray, adjustable feet, and the conveyor cassette are packed separately in the box and need to be
assembled to the unit as per the instructions below.
1. Lay the unit on its side and screw the adjustable feet into position using the threaded holes provided.
Hand tighten the legs by gripping the steel shank and turning until it is seated firmly against the
bottom of the toaster. Set the toaster upright on a flat and level surface. The unit can then be levelled
using the adjustable part of the leg.
NOTE: The unit must not be used without the feet being in position.
2. Remove the butter roller (A2) by pushing the shaft to the right to disengage from the drive socket.
3. Remove the butter pan (A3) by lifting o the locating pins.
4. Remove the top panel (A1) using the two black knobs provided to lift up and slightly backwards.
5. The bottom panel (A4) can now be removed. Hold the top edge with one hand and pull straight back.
Hold the bottom with the other hand and lift up and towards the front. Slide the panel down and out
below the butter roller bushes.
ASSEMBLY AND CONVEYOR
A B

User Manual
Vertical Contact Bun Toasters
5
www.AvantcoEquipment.com
1
Installation
1. Lay the non-stick sheet on a flat surface and measure
approximately 2" from the end of the sheet. Notch the
corners at 45 degrees as needed
NOTE: Some non-stick sheets may already have notched
corners) and fold a flap 2" long. Carefully crease the flap
at the 2" fold.
2. Remove the bun feeder chute (A7). From the rear of
the non-stick sheet retainer bracket (C1), slip the 2’’
fold under the bracket. Bring the balance of the sheet
forwards and smooth the sheet down against the grill
plate. See Diagram C.
3. Reinstall the feeder shoot.
6. Install the cleaned conveyor cassette (A8). Refer to specific cleaning instructions (page 7) as follows.
Grasp the conveyor cassette by the handles provided and place the locating pins into the adjustable
hanger brackets. Push the conveyor cassette forwards gently to engage the drive gear (B). The
cassette assembly height bolt is preset from the factory. If the cassette gear does not make adequate
contact, or is binding with the drive gear, tighten or loosen the height bolt to ensure proper contact.
NOTE: Care must be taken in fitting the conveyor cassette. The cassette is heavy and it is important that it
is not dropped into place to avoid potential damage to the drive gears.
7. Replace the bottom panel (A4), the top panel (A1), the butter pan (A4) and the butter roller (A2) in that
order.
8. Install the bun feeder chute by feeding the slots on each side onto the back panel studs.
NONSTICK SHEET C
NOTE: It is highly recommended that you install the non-stick sheet for best performance. Every unit is
shipped with (10) non-stick sheets. Please contact customer service if you did not receive these sheets.
If you do not install the non-stick sheet, there is a risk that buns will stick to the plate and burn. Built up
residue and grease can cause poor performance and will be considered as operator negligence in a
warranty claim, and thus void the warranty. To avoid this use non-stick sheet and clean unit frequently.
See below for instructions on installing the non-stick sheet.

User Manual
Vertical Contact Bun Toasters
6
www.AvantcoEquipment.com
Operation
1. Thoroughly clean the unit as described in the cleaning
section of this manual.
2. Turn on the main switch. The conveyor will now run.
3. Set the temperature to approx. 400˚F, which is between 6
and 7 on the scale. When using the recommended non-stick
sheet, it is advisable to increase the temperature setting to
approx. 450˚F, which equates to 6.5 on the scale.
NOTE: Approximate temperatures by scale:
1: 85°F, 2: 140°F, 3: 200°F, 4: 285°F, 5: 350°F, 6: 410°F, 7: 480°F
4. Set the conveyor speed between 4 and 6 to start. The color
of the bun is aected by the speed of the conveyor. The
faster the conveyor, the lighter the color; the slower the
conveyor, the darker the color. See diagram D.
5. Any high-quality edible oil can be used with this bun toaster.
It is preferable to use oil specifically suited for use in toasters.
NOTE: Using too little oil will cause the bun surface to be cool
and uneven in color. It will also cause the bun to stick to the grill.
Using too much oil will give the bun a yellow un-toasted look.
The indicator light works with the heating element and
indicates when the heater is on. It is referable to wait until
the unit has reached operating temperature and the light
has cycled on and o twice.
NOTE: Heat up time is about 15-20 min. for 208/240V,
and about 20-30 min. for 120V.
NOTE: Try several buns to determine the correct pressure,
temperature, and time to achieve the desired browning of bun.
6. Heat the toaster oil to melting point and carefully fill the
butter tray 2/3 full. Turn on the butter roller using the switch
provided.
7. Hold the bun half in the palm of the hand and in one motion
slide the sliced side of the bun onto the butter roller. Drop
the bun with the sliced surface towards the grill plate using
the feeder chute provided. See diagram E.
8. The toasted bun will drop out into the receiving tray at the
bottom of the unit.
NOTE: The toasted color of the bun can be adjusted lighter or
darker by using the temperature control, the speed control, or a
combination of both. When optimal bun color and speed have
been achieved, it is recommended to take note of the settings
for future reference.
NOTE: Should the temperature setting be changed, allow
several cycles for the plate to adjust.
Darker Lighter
r;u-ঞom
4.
Ɛĺ $_ouo]_Ѵ1Ѵ;-m|_;mb|-v7;v1ub0;7bm|_;1Ѵ;-mbm]v;1ঞomo=|_bvl-m-Ѵomr-];ƕĺ
Ƒĺ $umom|_;l-bmvb|1_|_;1om;oubѴѴmoumĺ
ƒĺ ";||_;|;lr;u-|u;|o-rruoĺƓƏƏ_b1_;t-|;v|oƔĺƕom|_;v1-Ѵ;ĺ=vbm]|_;orঞom-Ѵ
 $;Yomv_;;|b|bv-7bv-0Ѵ;|obm1u;-v;|_;|;lr;u-|u;v;মm]|o-rruoĺƓƔƏ_b1_
 ;t-|;v|oѵĺƔom|_;v1-Ѵ;ĺ
Ɠĺ m_b]_Ŋt-Ѵb|;7b0Ѵ;obѴ1-m0;v;7b|_|_bv0m|o-v|;uĺ|bvru;=;u-0Ѵ;|ov;obѴ
 vr;1bC1-ѴѴvb|;7=ouv;bm|o-v|;uvĺ
Ɣĺ $_;rbѴo|11Ѵ;11Ѵ;vb|_|_;_;-ঞm];Ѵ;l;m|-m7bm7b1-|;v_;m|_;_;-|;ubvomĺ|bv
 ru;=;u-0Ѵ;|o-b|mঞѴ|_;mb|_-vu;-1_;7or;u-ঞm]|;lr;u-|u;-m7|_;Ѵb]_|_-v11Ѵ;7
 om-m7o@|b1;ĺ
ѵĺ ;-||_;|o-v|;uobѴ|ol;Ѵঞm]robm|-m71-u;=ѴѴCѴѴ|_;0;u|u-Ƒņƒ=ѴѴĺ$umom|_;
 0;uuoѴѴ;uvbm]|_;vb|1_ruob7;7ĺ
ƕĺ oѴ7|_;0m_-Ѵ=bm|_;r-Ѵlo=|_;_-m7-m7bmom;loঞomvѴb7;|_;vѴb1;7vb7;o=|_;0m
 om|o|_;0;uuoѴѴ;uĺuor|_;0mb|_|_;vѴb1;7vu=-1;|o-u7v|_;]ubѴѴrѴ-|;vbm]|_;
 =;;7;u1_|;ruob7;7ĺ";;7b-]u-lĺ
Ѷĺ $_;|o-v|;70mbѴѴ7uoro|bm|o|_;u;1;bbm]|u--||_;0oolo=|_;mb|ĺ
$Ĺ
$$"$&!$&&"$$!!!!+&"$
$!$&!$!!$"$!!$$ĺ)
$&&&!"(($"!$"$
$"$$"!&$&!!!ĺ
C.
D
E
GENERAL USE

User Manual
Vertical Contact Bun Toasters
7
www.AvantcoEquipment.com
Operation
Cleaning
5.
$Ĺ
$&$&"$"$!$)!"&!)$)
!$"ĺ
Ɛĺ ѴѴo=|_;u;lo-0Ѵ;r-m;Ѵv1-m0;1Ѵ;-m;7;b|_;ubm-vbmhb|__o|-|;u-m77;|;u];m|ou
 rѴ-1;7bm-7bv_-v_;uĺ
Ƒĺ |bvu;1oll;m7;7|_;1om;ou1-vv;;bvomѴ1Ѵ;-m;7bm-vbmhb|_u;]Ѵ-u7;|;u];m|ĺ
 -h;vu;|_;1_-bmv-u;Ѵ0ub1-|;7-[;u1Ѵ;-mbm]b|_-vb|-0Ѵ;|o-v|;uobѴĺ
ƒĺ $_;]ubѴѴrѴ-|;1-m0;1Ѵ;-m;71-m0;1Ѵ;-m;7b|_-vb|-0Ѵ;]ubѴѴrѴ-|;v1ou;uĺ[;u7ubm]-
 Ѵb]_|CѴlo=|o-v|;uobѴv_oѴ70;-rrѴb;7ĺ
1
2
1
3
4
5
6
7
8
8
screws
D.
adjustment bracket
F
CONVEYOR ADJUSTMENT
If optimal bun grilling is not achieved using the speed and temperature settings, it is possible to adjust the
position of the conveyor system relative to the grill plate. Moving the conveyor closer to the grill plate will
apply more pressure to the bun and result in more eective toasting.
1. Switch o the unit and allow to cool down.
2. Remove the butter roller and tray and feed chute.
3. Remove the top panel and the bottom panel.
4. Remove the conveyor cassette carefully by lifting up and
pulling towards the front
NOTE: The conveyor is heavy and must be handled carefully.
5. The hanger adjustment brackets will now be exposed.
Loosen the brackets and move them EQUALLY towards the
grill plate in increments of 1/8”. See diagram F.
6. Retighten the bracket screws.
7. Adjust the drive gear engagement as needed with the bolts
at the bottom of the hanger plate. Ensure that the lock nuts
are retightened.
Cleaning & Maintenance
CAUTION: The unit must be disconnected from the power source and allowed to cool down before
cleaning takes place.
1. All of the removable panels can be cleaned either in a sink with hot water and detergent or placed in
a dishwasher.
2. It is recommended the conveyor cassette is only cleaned in a sink with regular detergent.
3. Make sure the chains are lubricated after cleaning with a suitable toaster oil.
4. The grill plate can be cleaned with a suitable grill plate scourer.
After drying, a light film of toaster oil should be applied.
NOTE: It is recommended that the non-stick sheet is replaced every 30 days, or when buns start
sticking, whichever comes first.
NOTE: The conveyor must stay clean to optimize speed and bun temperature.

User Manual
Vertical Contact Bun Toasters
8
www.AvantcoEquipment.com
Problem Possible Causes Action
Unit dead, no power.
No power at wall receptacle. Check supply circuit breaker.
Plug disconnected. Check that plug is fully connected.
Main switch o. Check that the switch is on.
Supply circuit breaker tripped. Check circuit breaker and reset.
Unit not heating.
Faulty thermostat. Replace thermostat.
Faulty heating element. Replace heating element.
Loose wire connections. Check wiring connections.
Main switch o. Check that the switch is on.
Conveyor and butter roller
not working.
Loose wire connections. Check wiring connections.
Faulty main switch. Replace main switch.
Faulty butter roller switch. Replace butter roller switch.
Butter roller not turning.
Section 3 possible causes. Section 3 actions.
Roller shaft incorrectly inserted into
drive socket.
Check roller is properly engaged into
drive socket.
Faulty motor. Check and replace motor.
Main conveyor not turning.
Section 3 possible causes. Section 3 actions.
Drive gears not engaging. Reinstall conveyor.
Conveyor linkage binding. Check conveyor for bent or faulty links.
Faulty speed control dial. Replace speed control dial.
Faulty conveyor cassette. Replace conveyor cassette.
Buns toast unevenly.
Insucient conveyor pressure. Adjust conveyor as per instructions.
Poor application of oil or butter. Ensure even coating when using the
butter roller.
Poorly sliced buns. Ensure bread is cut correctly.
Buns tend to stick to grill
plate.
Non-stick sheet not being used. Install and use the recommended non-
stick sheet.
Wrong oil used. Ideally use toaster oil or coconut oil.
Grill plate has baked-on oil residue. Clean grill surface as per instructions.
Doughy buns or excess sugar can cause
sticking.
Consider using day old buns or
increasing the grill temperature.
Buns not properly defrosted. Fully defrost buns before placing in
machine.
Troubleshooting