Avaya P332G-ML User manual

Avaya P332G-ML
Quick Start Guide
Unpack
Rack mount (optional)
Connect the Cables
Configure
Run Web-based
Manager (optional)
Power up
11
22
33
44
55
66
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 1

Unpack
Check the package contents for the following:
If any items are missing or damaged, contact your supplier.
Equipment
• One Avaya P332G-ML Gigabit Ethernet Stackable Switch
• One AC power cable (AC version only)
• One RJ-45 console cable
• One RJ-45 to DB-9 serial terminal adapter
• One RJ-45 to DB-25 modem adapter
• Four rubber feet
• Four screws with washers for rack mounting
• One cable holder
Ethernet connection cables are not supplied
Documentation
• Avaya P332G-ML Quick Start Guide (this document)
• Avaya P332G-ML Release Notes
• Avaya P330 Documentation and Utilities CD (see below)
• Avaya Communication Warranty and License Agreement
Avaya P330 Documentation and Utilities CD
The CD contains the latest User's Guides for the Avaya P330 stackable switches and files for
use with the Embedded Web Manager.
Auxiliary Files for use with the Embedded Web Manager
Please refer to the documentation for information on how to use these files.
• Java plug-in
• Help files
Adobe® Acrobat® Reader
This application allows you to view and print the User's Guides on this CD.
11
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 2

Rack mount (optional)
1. Snap open the hinged ends of the unit’s front panel to reveal the screw holes.
2. Position the unit in the rack.
3. Secure the unit to the rack, taking care not to overtighten the screws.
4. Snap closed the hinged ends of the front panel.
You can now safely connect the cables to the unit.
22
WARNING: Disconnect all cables from the unit before proceeding with the rack
installation.
12
LAG
34 5 6
LAG
LNK
4
FCRxCOL Tx
1
FDX
3
2
LAG
Hspd
56711
OPRRout
8
SYS
10
9
PWR
12
107 8 9
LAG
11 12
CONSOLE
P332G-ML
12
LAG
34 5 6
LAG
LNK
4
FCRxCOL Tx
1
FDX
3
2
LAG
Hspd
56711
OPRRout
8
SYS
10
9
PWR
12
107 8 9
LAG
11 12
CONSOLE
P332G-ML
Closed hinged end
Open hinged end
Screw
holes
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 3

Power up
Avaya P332G-ML AC Version
1. Insert the power cord into the power connector (BUPS or AC Power Supply) on the rear of
the unit.
2. Insert the other end of the power cord into the electricity supply or the BUPS connector.
The unit powers up and performs a self test procedure. The LEDs flash at regular
intervals after the self-test procedure is completed successfully.
Avaya P332G-ML DC Version
WARNING: Before performing any of the following procedures, ensure that DC
power is OFF.
CAUTION: This product is intended for installation in restricted access areas and is
approved for use with 18 AWG copper conductors only. The installation must comply
with all applicable codes.
1. Connect the power cable to the switch at the input terminal block on the rear of the unit.
The terminals are marked “+”, “-“ and the IEC 5019a Ground symbol.
The size of the three screws in the terminal block is M3.5.
The pitch between each screw is 9.5mm.
2. Connect the power cable to the DC power supply.
WARNING: The proper wiring sequence is:
• ground to ground
•positive to positive
•negative to negative
Always connect the ground wire first and disconnect it last.
The unit powers up and performs a self test procedure. The LEDs flash at regular
intervals after the self-test procedure is completed successfully.
Cable to
Lower Unit
Cable to
Upper Unit
33
Cable to
Lower Unit
Cable to
Upper Unit
BUPS connector
AC connector
DC terminal
block
BUPS connector
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 4

44
LNK
4
FCRxCOL Tx
1
FDX
3
2
LAG
Hspd
56711
OPRRout
8
SYS
10
9
PWR
12
LNK – When ON, port enabled and link up
When blinking, port is enabled, link down
COL – Not applicable
Tx, Rx – Shows traffic activity for
transmitted and received packets
FDX – Shows Full Duplex mode (always on)
FC – When ON, Flow Control is enabled
Hspd – Always ON
LAG – When ON, the port is included in a Link
Aggregation Group (LAG).
ROUT – When ON the switch is in Router mode
SYS – Shows whether this module is the
Avaya P330 Stack Master
OPR – Shows CPU boot status (ON = OK)
PWR – ON: Power from main AC/DC source
Blinking: Power received from BUPS
Connect the cables
Connect PCs, servers, routers, workstations, and hubs
1. Insert an SFP GBIC (Small Form Factor Pluggable Gigabit Interface Converter) transceiver
(not supplied). For a list of approved SFP GBIC transceivers, see www.avayanetwork.com.
2. Connect the Ethernet fiber optic cable (not supplied) to the GBIC transceiver on the front
panel of the Avaya P332G-ML.
You can use LC or MT-RJ fiber optic cables, depending on the GBIC transceiver you are
using.
3. Connect the other end of the cable to the Ethernet port of the PC, server, router, worksta-
tion, switch or hub.
4. Check that the appropriate link (LNK) LED lights up.
Connect the console cable
1. Configure the serial port settings of the PC or terminal as follows: Baud Rate – 9600,
Parity – no, Data bits – 8, Stop bits – 1, Flow control – no.
2. Connect the supplied special console cable to the port marked “Console” on the front
panel of the Avaya P332G-ML.
3. Connect the other end of the cable to a terminal or PC with terminal emulation software
installed via the supplied RJ-45 to DB-9 adapter.
P332G-ML LEDs
Left/Right &
Reset Switches Function LEDs
Port LEDs
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 5

55
Basic configuration
To connect a PC terminal or VT-100 terminal to the Avaya P332G-ML
1. If you are using a PC, initiate a VT-100 terminal emulation session using an application
such as Windows® HyperTerminal.
2. Press Enter.
3. Type the User name root when prompted and press Enter.
4. Type the default password root when prompted and press Enter.
The P330-N(super)# prompt appears
Nis the number of the switch in the stack.
Assigning the Stack IP Address
Commands are shown as follows: set interface inband;
parameters which you need to enter are shown in <> as follows: <vlan>
1. Type set interface inband <vlan> <ip_address> <netmask>, replacing
<vlan>, <ip_address> and <netmask> with the VLAN, IP address and net mask of the
stack and press Enter.
2. Type reset and press Enter.
3. Type Yand press Enter to reset the stack.
4. After the reset, perform login again as described above.
The P330-N(super)# prompt appears.
5. Type set ip route <destination> <gateway>, replacing <destination> and <gate-
way> with the destination and gateway IP addresses.
6. Press Enter to save the destination and gateway IP addresses.
If you want to define the Initial Router IP address, continue to “Assigning the Initial
Router IP Address”.
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 6

Initial Router Configuration
This section is only applicable if you either purchased a preconfigured P332G-ML,
or purchased a Routing License Key Certificate and activated the License Key.
If you purchased a preconfigured switch, go to step 3.
1. To request a License Key, go to: http//license-lsg.avaya.com.
2. To activate the License Key, type set license <module number> <license key>
routing where <module number> is the location of the switch in the stack and <license
key> is the number you obtained from the above Web site and press Enter
3. Type set device-mode router and press Enter.
You will be prompted to reset the module.
4. Type y.
Wait for the module to restart and for the CLI prompt to reappear.
5. Type show device-mode and press Enter to ensure that the module is in router mode.
Assign the stack IP address as described in “Assigning the Stack IP Address” before you
assign the Initial Router IP Address.
6. Type session <module number> router where <module number> is the location of
the P332G-ML in the stack and press Enter.
The Router-N# prompt appears.
N is the number of the router in the stack.
7. Type configure and press Enter.
The Router-N (configure)# prompt appears.
If the IP interface is not on VLAN 1 then continue to step 8, otherwise skip to
step 10.
8. Create the management/routing VLAN by typing
set vlan <Vlan-ID> name <Vlan-name>,replacing <VLAN-ID> by the VLAN
number; and <Vlan-name> by the VLAN name and press Enter.
9. Create an IP interface name by typing interface <interface name> and pressing
Enter.
The Router (configure-if:<interface-name>)# prompt appears
10. Assign the IP address and network mask of the IP interface you have created by typing
ip address <ip-address> <netmask> and pressing Enter.
11. Assign the VLAN created in step 9 to the IP interface by typing ip vlan <Vlan-id> or
ip vlan name <Vlan-name> and pressing Enter.
12. Type exit and press Enter.
This returns you to the Router (configure)# prompt
If the management station is not on the same subnet as the switch proceed to step 13,
otherwise skip to step 14.
13. Configure a default gateway (static route) by typing
ip default-gateway <ip-address> and pressing Enter, replacing <ip address> with
the IP address of the default gateway.
14. Save the configuration changes by typing copy running-config startup-config
and pressing Enter.
Once you have assigned an IP address/interface to the Avaya P332G-ML, you can either
configure it using the Avaya P330 Manager or continue using the CLI.
55
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 7

Configuration Parameter Default Setting
Port Speed 1000 Mbps, Full Duplex
Flow Control Disabled (no pause)
Administrative State Enabled
Auto-negotiation Enabled*
Port VLAN ID 1
Tagging Mode Clear
Port Priority 0
*Ensure that the other side is also set to Autonegotiation enabled
Setting the Parameters
If you wish to change the default parameters shown and configure the mandatory
parameters, we recommend that you use the Command Line Interface (CLI).
For further information, please refer to the Avaya P332G-ML User’s Guide.
Configuration Parameter Default Setting
Avaya P330 IP Address 149.49.35.214
Subnet Mask 255.255.255.0
Default Gateway 0.0.0.0
VLAN Management ID 1
Spanning Tree Enabled
SNMP Communities
Read-only Public
Read-Write Public
Traps Public
User Name/Password root/root
Keep Alive frame transmission Enabled
Network time acquisition Enabled, TIME Protocol
55
Main Default Switch Parameters
Main Default Port Parameters
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 8

Run the Web-Based Manager (optional)
To configure the Avaya P332G-ML you can use the P330 Web-based Manager in
addition to using the CLI.
System Requirements
Minimum hardware and Operating System requirements are:
• Pentium® II 400 Mhz-based computer with 128 Mb of RAM
• Screen resolution of 1024 x 768 pixels
• Microsoft® Internet Explorer® 5 or Netscape Navigator® 4.x
• Windows® 95, NT® 4.0 (server/workstation) or Windows 2000 (server/workstation)
• Sun Microsystems Java™ plug-in version 1.2.2 (supplied)
Running the Embedded Manager
Assign an IP address to the Master Switch before starting this procedure.
1. Open your browser.
2. Enter the URL of the switch in the form http://aaa.bbb.ccc.ddd
aaa.bbb.ccc.ddd is the IP address of the switch.
You are prompted to log into the switch.
The user name is “root”.
The default password for read-write access is “root”.
The Web management passwords are the same as those of the CLI. If you have created
additional CLI user names or changed the default passwords then you can use those
passwords for Web management as well.
The welcome page is displayed:
66
Avaya P332G-ML QS.qxd 16/9/2001 9:17 Page 9

If the network manager has configured the system the plug-in should be installed auto-
matically.
If the plug-in is not installed automatically, there are three ways to install the plug-in
manually:
• Either install the plug-in from the CD as follows:
1.Close all unnecessary applications on your PC.
2.Insert the “Avaya P330 Documentation and Utilities” CD in the CD drive.
3.Click Start on the Task bar.
4.Select Run.
5.Type x:\emweb-aux-files\plugin_1_2_2.exe (where x: is the CD drive letter)
6.Follow the on-screen instructions.
• Or install the plug-in from the Avaya site by clicking on the link on the welcome page.
• Or, if the network manager has placed the files on the local site, install the plug-in from
there by clicking the link on the welcome page.
If you have the Java plug-in already installed or once you have successfully installed the
plug-in as described above, the Web-based manager opens in your browser.
66
Avaya P332G-ML QS.qxd 16/9/2001 9:18 Page 10

Documentation and Online Help
Refer to the Avaya P330 Documentation and Utilities CD for full instructions
Avaya P332G-ML QS.qxd 16/9/2001 9:18 Page 11

Contact Information
To contact Avaya technical support:
From the United States:
Please call 1-800-237-0016, press 0, then press 73300.
From outside the United States:
EMEA (Europe, Middle East and Africa). Email: [email protected]
AP (Asia Pacific). Email: [email protected]
CALA (Caribbean and Latin America). Email: [email protected]
Hot Line: [phone]
Fax: [phone]
For updated information, visit www.avayanetwork.com, and click “Global Support
Organization (GSO)”.
aavvaayyaa..ccoomm
All trademarks, registered trademarks, service names, product and/or brand names are the sole property of their respective owners.
Copyright © 2001, Avaya Inc. All rights reserved.
Catalog No. DO0625 Rev. 0. September 2001
Country Local Dial-In Number
Albania [phone]
Austria [phone]
Azerbadjan [phone]
Bahrain +800 610
Belgium [phone]
Belorussia [phone]
Bosnia Herzegovina [phone]
Bulgaria [phone]
Croatia [phone]
Cyprus [phone]
Czech Rep. [phone]
Denmark [phone]
Egypt [phone]
Estonia [phone]
Finland [phone]
France [phone]
Germany [phone]
Ghana [phone]
Gibraltar [phone]
Greece +00800 3122 1288
Hungary +06800 13839
Iceland +0800 8125
Country Local Dial-In Number
Ireland [phone]
Israel [phone]
Italy [phone]
Jordan [phone]
Kazakhstan [phone]
Kenya [phone]
Kuwait [phone]
Latvia [phone]
Lebanon [phone]
Lithuania [phone]
Luxemburg [phone]
Macedonia [phone]
Malta [phone]
Mauritius [phone]
Morocco [phone]
Netherlands [phone]
Nigeria [phone]
Norway [phone]
Oman [phone]
Pakistan [phone]
Poland +0800 311 1273
Country Local Dial-In Number
Qatar [phone]
Portugal [phone]
Romania [phone]
Russia [phone]
Saudi Arabia [phone]
Slovakia [phone]
Slovenia [phone]
South Africa +0800 995 059
Spain [phone]
Sweden [phone]
Switzerland [phone]
Tanzania [phone]
Tunisia [phone]
Turkey [phone]
Uganda [phone]
Ukraine [phone]
UAE [phone]
UK [phone]
Uzbekistan [phone]
Yemen [phone]
Yugoslavia [phone]
Zimbabwe [phone]
Country Local Dial-In Number
Australia [phone]
Hong Kong [phone]
Indonesia [phone]
Japan +0 120 766 227
Country Local Dial-In Number
Korea +0 80 766 2580
Malaysia [phone]
New Zealand +00 800 9828 9828
Country Local Dial-In Number
Philippines [phone]
Singapore [phone]
Taiwan +0 80 025 227
Avaya P332G-ML QS.qxd 16/9/2001 9:18 Page 12