AVE SINUS - 1K User manual
Vertriebs-
Entwicklungsgesellschaft
mbH
SINUS - 1K
Mixing amplifier
User Guide
Table of contents
1. Introduction
2. Safety instructions
3. Description of components and functions
4. Technical specifications
1. Introduction
Thank you for choosing the A.V.E. mixing amplifier SINUS - 1K with five
microphone/line inputs and a switchable CD/Aux.-Input. It was designed particularly for
superior audio quality in churches as well as other utilizations with acoustically difficult
room proportions. It’s possible to achieve an optimized acoustic pattern every time.
Each microphone/line input is equipped with a Gain-controller, a 3-band equalizer,
indicators for volume and operating status. Additionally it’s equipped with a switchable
input (CD/Aux) with a separate treble- and bass control. A graphic 9-band equalizer
acts only on the inputs 1–5.
All signal sources can be controlled by master volume control. SINUS - 1K has a VU
meter and a clipping und protection indication.
Therefore SINUS –1K is qualified to sound each kind of critical spaces.
2. Safety instructions
Please read the information provided in this manual before starting up the unit.
WITHIN THIS UNIT THERE IS DANGEROUS VOLTAGE PRESENT CONSTITUTING A RISK OF ELECTRIC SHOCK.
DO NOT OPEN THE COVER.INTERNAL MODIFICATIONS ARE TO BE COMPLETED BY AUTHORIZED
PERSONNEL ONLY.
The SINUS - 1K is equipped with an approved power cable. At one end there is a three-
pole mains connection
socket (rubber connector) and at the other end a CE-standardized Schuko-socket to
connect to a 230 V/ 50 Hz voltage source. Please take care, not to damage these power
cords. Do not use any defective or damaged power cords!
3. Description of components and their functions
1. Control dial for GAIN, THD, treble, middle and bass
The 4 potentiometers per channel allow following adjustments:
Gain: The Gain-controller customizes the amplification of the channel to the
level of the signal source of the input.
With the 3-band-equalizer (treble, middle and bass) the microphone is
adapted to the speaker to achieve an optimized sound.
Treble: ±12 dB at 10 kHz
Middle: ± 12 dB at 700 Hz
Bass: ± 12 dB at 70 Hz
2. Signal display (for channel 1 –5):
Optical display of activated e.g. overdriven input.
3. Volume control (for channel 1 –5):
With these volume controls all levels of the signal sources can be adjusted which
are plugged to the microphone/line-inputs (26). During installation by authorized
experts the optimized level will be marked with a sign.
4. Volume control for CD/Aux
5. Bass and treble control for CD/Aux
6. Master control
7. Power switch
8. 4 Output switches with optical display
9. VU meter, Out State display
Red: amplifier overdriven at input
Yellow: failure
When switching on the amplifier the LED flashes short time and disappears
afterwards.
10. Graphical 9-band equalizer
11. Channel switch CD/Aux:
Sound carrier selection. The reproducers can be connected at the backside.
12 11 10
13
1 2 3 4 5 6 7 8
1. PRE OUT 2 connection for additional amplifiers 0 dB.
2. Optional remote control
3. Sensitivity control AUX
4. Cinch-connection AUX
5. Cinch-connection CD
6. Cinch-connection for recording units
7. Direct OUT +6 dB:
Direct output without any signal processing. This output can be used for example
for transmission of the direct room settings to external rooms.
8. Level Direct OUT controls the volume oft he direct output.
9. DIP switch phantom power 48 V, line, micro low, micro high
10. Microphone/Line-inputs
11. Connection terminals for loudspeakers 1 –4 (50, 70, 100 V, 4 Ohm)
12. Power supply
13. Fuse 3,15 A
Optional Remote Control
By insertion of the print
the possibility is given to
regulate the outputs from
distance.
Therefore jumper 11 must
be unsoldered. B
y
i
n
s
e
Mute-Switch for all or
alternatively favoured
inputs. By removing or
jumper 1 - 6 you can obtain
that a favoured input is
active despite of mute-
switch.
9
4. Technical Specifications
Line electronic balanced
Input sensitivity: -19 dBu 1dB
Frequency response: (-3dB): 40 Hz to 20 KHz
Microphone
Input sensitivity (mic high/mic low): -58 dBu/ -34 dBu ±1 dB
Frequency response (-3dB) input microphone: 160 Hz bis 20 KHz
CMMR: > 60 dB @ 1 kHz
THD-level: 20 dB
Hi-pass-filter: 160 Hz, 6 dB/oct
Phantom power: + 48 V for each input selectable
Equalizer
Treble: ±12 dB @ 10 kHz
Middle: ±12 dB @ 700 Hz
Bass: ±12 dB @ 70 Hz
LED-display: green (signal)
AUX/CD
Impedance AUX: 20 kΩ
Impedance CD: 27 kΩ
Input sensitivity AUX: -13 dBu/+3 dBu ± 1 dB
Input sensitivity CD: +3 dBu
Frequency response (-3dB) input CD/AUX: 20 Hz to 20 KHz
CD/AUX EQ
Bass: ±12 dB @ 100 Hz
Treble: ±12 dB @ 10 kHz
Outputs
Output impedance PREOUT 2: 140 Ωbalanced; 70 Ωunbalanced
Output impedance PREOUT 2: 0 dBu
Output impedance DIRECT OUT: 140 Ωbalanced; 70 Ωunbalanced
Output level DIRECT OUT: +9 dBu (variable potentiometer)
Output impedance REC: 70 Ω unbalanced
Output level REC: 0 dBu
Noise
Noise level OUT 2 (20 Hz –20 kHz) master volume at 0: -95 dBu
Noise level OUT 2 (20 Hz –20 KHz) master Volume max.: -80 dBu
Noise level CD/AUX (20 Hz –20 KHz) master volume max.: -80 dBu
On Mic (20 Hz –20 kHz) Rs = 150 Ω : -124 dBV
Output power
Output power: 1x150 W, 1x240 W
Output impedance: 50V/70V/100V
LED-display: yellow (dysfunction), red (overdriving)
General
Remote control: optional remote control for both outputs
Mute: Muting for each input
Operating voltage: 230 V~, 50-60 Hz
Power consumption: 80 W (1x150), 115 W (1x240)
Dimensions (W x H x D): 483 x 88 x 340 mm
Weight: 9,5 kg (1x150), 10,5 kg (1x240)
BEFORE OPENING THE UNIT,TURN IT OFF AND REMOVE THE POWER CORD.
ONLY THEN REMOVE THE SCREWS AND THE COVER.
Notice
ALL AVE mbH DESIGN SPECIFICATIONS, FILES, DRAWINGS, TABLES, LISTS, AND
OTHER DOCUMENTS ARE BEING PROVIDED “AS IS.”
AVE mbH MAKES NO WARRANTIES, EXPRESSED, IMPLIED, STATUTORY, OR
OTHERWISE WITH RESPECT TO THE MATERIALS, AND EXPRESSLY DISCLAIMS ALL
IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY, AND FITNESS
FOR A PARTICULAR PURPOSE.
Information furnished is believed to be accurate and reliable. However, AVE mbH
assumes no responsibility for the consequences of use of such information or for
any infringement of patents or other rights of third parties that may result from its
use. No license is granted by implication or otherwise under any patent or patent
rights of AVE mbH. Specifications mentioned in this publication are subject to
change without notice. This publication supersedes and replaces all information
previously supplied. AVE mbH products are not authorized for use as critical
components in life support devices or systems without express written approval of
AVE mbH Corporation.
Trademarks
AVE mbH and the AVE logo are trademarks or registered trademarks of AVE mbH
in the Germany and other countries. Other company and product names may be
trademarks of the respective companies with which they are associated.
Copyright
© 2015 AVE mbH. All rights reserved.
Consulting • Planning • Developing • Assembly of electroacoustic sound systems
AVE GmbH • Gustav-Rau-Straße 6 • 74321 Bietigheim-Bissingen • Germany
phone: +49 (0)7142 78879-0 • fax: +49 (0)7142 78879-18
info@ave-stuttgart.de • www.ave-stuttgart.de
Other AVE Amplifier manuals
