AVF SYZ84-S-XL User manual

VF
I
Assembly Instructions
SYZ84-S-XL Stand
Thank you for purchasing AVF’s SYZ84 Stand
This product is designed for free standing mounting of single plasma/lcd display sized 40”-58” (S), 58”-80” (X) weighing
Confirm all hardware is included before you begin assembly.
Read these instructions start to finish before beginning installation.
Have at least 3 people mount the display.
Note: If you cannot understand these instructions or are concerned about safety of the installation contact a qualified
contractor or contact AVF at 1-877-834-3876
Supplied Parts
Structural Tube
(1)
Supplied Hardware Kapp 42/84
Black Spacer
(4)
M10 X 35
(4) Adhesive Bumper
(2)
1
www.video-furn.com 190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
www.video-furn.com 190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
M6 X 25
(10)
Base with wheels
(1)
Not all hardware supplied will be used, depending on the manufacturer of your display.
Hardware Bag
(3)
•Kit Kapp 42/84
•2 Kit TV52-70
•Kit Grommet
& Bumper
Tools required
TV Bracket
(2)
Hex Key M6 (Supplied in Hardware Kit Kapp 42)
Hex Key 8mm (Supplied in Hardware Kit TV 52-70)
10mm wrench
Back Plate
(1)
M6 Lock Washer
(6)
M6 Washer
(6)
Grommet
(2)
Supplied Hardware Bumper & Grommet
Tube Bracket
(1)
Tube
(1)
Kit TV52-70 (2) Kit Grommet & Bumper

4
VF
I
Assembly Instructions
SYZ84-S-XL Stand
www.video-furn.com 190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
Place parts on non abrasive surface; install base to structure tube
From under the base hand tighten all 4 X M10
bolts onto the holes attaching the structural
base to it. Tighten securely with Hex Key
Make sure the open section of the tube is
closer to the near edge of the base.
1
2
Lift the stand
M10 X 35
(4)
M6 X 25 mm (4)
3
Place the tube bracket over the tube
with the arrow pointing up.
Insert ( 4) M6 X 25mm to secure bracket
into tube. If needed add a washer
Use the Hex key to tighten.
2
Place back plate onto structural tube and
insert M6 washer (6) with M6 X 25 (6) onto
middle and bottom to secure the back plate
Use the Hex key to tighten
Insert 2 round grommets onto the plate
M6 X 25 (6)
Grommet (2)
5
Insert mounting bar through the tube
bracket
Center the bar and secure with (2) M8 x
20mm on the 2 side plates of the bracket
to angle the bar.
M8 X 20 mm (2)
Arrow

8
VF
I
Assembly Instructions
SYZ84-S-XL Stand
3
www.video-furn.com 190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
Assembly is complete, enjoy your stand
6
7
With assistance lift the TV into position and
hook onto the mounting bar.
Centre and secure to the bar with 2 M8 bolt.
M8
Before installing mounting brackets attach these
to TV and secure tightly before mounting.
DO NOT OVERGTHIGHTEN AS THIS CAN
DAMAGE OR PUNCTURE THE MONITOR.
Insert (2) M8 x 20mm bolts on the top and
bottom of tube bracket to secure it.
Use the hex key to tighten.
7M8 bolt (4)
M6 bolt (4)
M8 x 20mm (4)