AVIT Gear G3 Series User manual
G3 series Wireless User Manual
www.avitgear.com
Please read the instruction carefully before connecting, operating or
adjusting the G3 series V1.3
This User Manual Applies to both models of AVIT Gear G3 series
The AVIT Gear Wireless HDMI Set include a Transmitter and Receiver, it
Transmits high definition video and audio to any HDTV display up to
30 meters
The G3-1080 supports resolutions up to 1080p/60 Full HD, 3DTV, CEC, and 7.1-channels
of High Bit Rate (HBR) lossless digital audio such as Dolby True HD, DTS -HD Master
Audio
The G3-UHD supports resolutions up to 2160P/30 (3840 x 2160P) Full HD, 3DTV, CEC, and
7.1-channels
of High Bit Rate (HBR) lossless digital audio such as Dolby True HD, DTS -HD Master
Audio
The G3 series Wireless kits are specifically designed to transmit within a room and not be used
beside another transmitting set
Best Practice For Operation
●Placement of Transmitter is at source end, and receiver at Display
●To ensure trouble-free operation, the device may only be used indoors, it is NOT
suitable for outdoor use
●Always place the transmitter and receiver on a flat surface and ensure that the USB
cables and HDMI are not under voltage or near heat sources
●The G3 is designed for use in a single room, for the best transmission performance
there should be a clear line of sight between transmitter and receiver (up to 30m) and
you should use a good Quality HDMI cable
●Transmitter and receiver must not come in contact with liquids. This will void your
warranty
●If you notice external damage to the equipment or unexpected or unusual operation,
the system should not be used. In these cases, disconnect the devices from power
●We recommend turn off both devices when not in use, this can be achieved via CEC
presets on a display, or a power multiport device with pre-set command functionality
1
Features - Support for CEC Commands
Supports Video Resolutions:
G3-1080 480i/576i to 1080p@60Hz
G3-UHD Support resolution 480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz,
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz, 2K4K@24/25/30Hz,3840X2160UHD
3D video support 1080p/720p
Wireless HD 1.1 Compliant
Compliant with HDMI1.4, HDCP2.0
Supports Dolby TrueHD, DTS -HD Master Audio and LPCM digital audio streams
Up to 7.l channels
Uncompressed High Definition A/V from source to display
Near zero latency
Wireless extension of HDMI up to 30 meters
Bandwidth: 7Gbps
Intermediate frequency: 60GHz(59~66GHz)
Radio-frequency power: 10dBm
Security agreement: HDCP
With Your Package You Will Receive The Following Items
1 only Transmitter, 1 only receiver, 2 micro USB to USB cables
Note: You will require HDMI cables and USB – 230v Adaptors if you cannot use the USB of the
devices
Specifications:
Frequency Band Range: 60 GHz ( 59.40 Ghz -63.56 Ghz)
G3-1080 Input resolution (Transmitter): up to 1080P@60Hz
G3-1080 Output resolution (Receiver): up to 1080P@60Hz
G3-UHD Input resolution (Transmitter): up to 2160P@30Hz
G3-UHD Output resolution (Receiver): up to 2160P@30Hz
Input ports (Transmitter): lx HDMI (Female type)
Output ports (Receiver): lx HDMI (Female type)
USB Connector (Transmitter/ Receiver): Micro USB
Form factor (mm): 90(W) x 90(D) x 22 (H)
Weight (g): Transmitter (158g)
Receiver (153g)
Operating Temperature: 0°C — 40°C / 32°F — 104°F
Storage Temperature: -20°C — 60°C 1 -4°F — 140°F
Power Consumption (Max): 3.5W
Power Consumption Standby: 0,2W
2
Operation:
Blue Link LED: The connection status indicating lamp is blue on both Transmitter & Receiver
Blue LED OFF: Means the adapter is powered OFF or in Sleep mode
Blue LED Slow Blink: Means the adapter has started radio transmission and has not yet found
the other side of the link:
●If the adapter is a transmitter, the adapter is in Scan mode, searching for a matching
receiver
●If the adapter is a Receiver, the adapter is in Beacon mode, searching for a paired and
matching transmitter
●This process can take a up to 2 minutes depending on placement and distance
between the transmitter & receiver
Blue LED Fast Blinking: Means the adapters are associated, which means that the receiver
and transmitter have accepted each other and established a WVLAN network
Blue LED ON: Means the transmitter and receiver adapters have established an audio/video
connection. At this point, the user should be able to see this transmission
happening on the display attached to the receiver
*If the blue LED on on both units and you are not viewing content from Source, make sure your
HDMI input is correct
*If you have video and no Audio, make sure the HDMI input on the display is selected correctly
as all HDMI inputs on a number of name brand Displays are not identical on performance and
specification
If you are unsure when connecting the devices, contact a specialist, your dealer
Compliance to Australian and New Zealand Standards
NZ RSM “Radio Spectrum Management” licence 265372 Classification as SRD device
Au & Registered ERAC E7275 & ACMA Class A1 Device
RCM
Thank you for your purchase of this product, if you have any questions relating to the product
please ask your local distributor or contact us directly and we will be happy to help you
Warranty 24 Months from date of Purchase
3
This manual suits for next models
2
Table of contents
