Avnet Newark CR1R User manual

INSTRUCTIONS FOR CR1R
(Remote for TV with CABLE BOX)
Works over 250 brands of commercial and retail TVs
No Menu button - So Patients and Guests cannot change settings
Hidden Battery compartment and attached door to help prevent batteries from being taken
Uses 2 AAA batteries
Compatible with Comcast® and other cable system boxes
Will not operate TV/DVD, VCR or DVD/VCR combination units. Will not operate with LodgenNet® or
Oncommand® movie systems
Battery Installation:
1. Open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid
upward from the back (photo A, step 2)
2. When placing AAA batteries in the compartment note the + and - symbols on the metal hinge should make contact
with the corresponding + and - end of each battery (photo B).
3. Closing cover: With keypad facing away from you gently close cover by pressing downward
(photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2)
4. Test remote by pressing the power button; the LED should light indicating that the batteries are in correctly. If the
LED doesn't light, then the batteries are either in wrong or the batteries are bad.
FORTVWITHANIDIVIDUALCABLEBOXINEACHGUESTROOM,STARTHERE:Ifyoudonot
haveanidividualcableboxineachguestroom,scrolldowntoTVONLYINSTRUCTIONS
1. ManuallyturnontheTVandtheCableBoxandthenstandbackabout5feetfromtheTV.Pointthe
remoteattheCENTERofthefrontpaneloftheTV.Itwillnotbenecessarytopointtheremoteatthat
exactareaoncetheremoteisset‐up.
2.PressandfirmlyHolddowntheSetupbutton,donotrelease.TheLEDwillblinkonceandthenafter
7secondsitwillinitiatecodesearch.TheLEDwillcontinuetoblinkevery2seconds.OnceyourTV
shutsoff,immediatelyremoveyourfingerfromtheSetupbutton;thecodeautomaticallylocksin.
3.TurnTVbackON,DONOTPRESSCHANNEL+/‐buttonsasyoumaychangeinputonTV.Testthe
remotetomakesurethatyouhavethecorrectcodebydoingthefollowing:PressPowerON/OFFand
VOLUME+/‐ONLY.
Ifpowerandvolumebuttonsworkcorrectlyontheremotethenproceedtostep#4.
IfyouinadvertentlychangedtheinputontheTV,manuallychangeitbackfromtheTV’scontrolpanel
andthentrypowerandvolumebuttonsONLY.
Ifthepowerandvolumekeysarenotworkingproperly,youmaynothaveanexactcodematch.Start
againatstep#2,thecodesearchwillcontinuewhereitleftoff.Onceyouhavethecorrectcode,goto
step#4toprogramthecablebox.

4.ToProgramtheCableBoxmakesurethecableboxandTVareon.Next,HoldDowntheCBLbutton
andCCbuttonatthesametimeandwaituntiltheLEDlightblinksquickly3times.Thenimmediately
releasebothbuttons.NowpointtheremotetowardthecableboxandTVandtrythechannelupand
downbuttonsandthechannelnumbers.Ifthechannelschangecorrectly,makesurevolumeandTV
poweronandoffworkandassumingtheydo,youaredone.
5.IfthechannelsarenotchangingproperlymakesuretheTVisonnowbutthecableboxisOFF.NOTE:
thistimeDONOTHOLDTHECCbuttondown,justpressandholddowntheCBLbutton.Firmlyholdthe
CBLbuttondownwhilepointingtheremoteatthecablebox(nottheTV).Whenthecableboxturnson,
immediatelyremoveyourfingerfromthebutton.NowturntheCABLEboxoffandthenbackonby
pressingtheCBLbuttononce(NottheTVpowerbutton).Nexttestchannelupanddownandthechannel
numbers.Ifthechannelschangecorrectly,makesurevolumeandTVpoweronandoffoperate,ifso,
youaredone.
Ifitisnotworkingproperlystartagainatstep#5.
IMPORTANTTROUBLESHOOTINGINFORMATION
A) IfyouthinkyoumissedtheTVcodeoraretestingremoteondifferentbrandTV’s,
orarehavingdifficultyoperatingTV;first,resettheremotebypressingandholdingtheSetup
buttonfor3secondsandthenwhilestillpressingtheSetupbuttondownpressandholddowntheCC
buttonatthesametimeuntiltheLEDlightblinksquickly3times,instantlyreleasebothbuttons.You
havenowresetthecodelistbacktothebeginning.Gobacktostep#1andrepeatallsteps#1through
#5again.
Note:Manycableboxesdonothaveaseparatepowerbuttonandarealwayson.Ifyourcablebox
doeshaveaseparatepowerbutton,onceyouhaveset‐upthecableboxtoworkwiththeClean
RemoteitcanbepoweredonoroffbypressingtheCBLbutton.
TVONLYINSTRUCTIONS,STARTHERE:IfyourTVisconnectedtoanindividualcableboxin
eachguestroomscrolluptostep1.
Note:Ifyou’vealreadysetuptheremotetoworkbothaTVandaCableBoxandnowwishtooperate
TVonly.HolddowntheCBLbuttonandSETUPbuttontogetheruntiltheremoteblinks3timesquickly
instantlyreleasebothbuttons.Thiswillresettheremotecompletely.
TurnontheTVandthenstandbackabout5feetfromTVandPointtheremoteattheCENTERofthe
frontpaneloftheTV.Itwillnotbenecessarytopointtheremoteatthatexactareaoncetheremote
isset‐up.
PressandfirmlyHolddowntheSetupbutton,donotrelease.TheLEDwillblinkonceandthenafter7
secondsitwillinitiatecodesearch.TheLEDwillcontinuetoblinkevery2seconds.OnceyourTV
shutsoffimmediatelyremoveyourfingerfromtheSetupbutton;thecodeautomaticallylocksin.
Testtheremote.Ifeverythingworks,youaredone.Ifthemainfunctionsarenotworkingproperly,
youmaynothaveanexactcodematch.Startagainatstep#1.Thecodesearchwillcontinuewhereit
leftoff.
ImportantNote:IfyouthinkyoumissedthecodeoraretestingremoteondifferentbrandTV's:
Resettheremotebacktothebeginningofthecodesearch;firstpressandholdthe
Setupbuttonfor3secondsandthenwhilestillpressingtheSetupbuttondown,pressandholdthe
CCbuttondownatthesametimeuntiltheredLEDlightblinksquickly3times.Youhavenowreset
thecodelistbacktothebeginning