Avol itrio User manual

www.AVL21c.com
User’s manual
(COMPOSITE Model)
REV. C. 1.0
Wireless Sender
Full HDFull HDFull HDFull HDFull HD
Full HD
English

English
Contents
3
Caution for Safety
Caution for Safety 4.....................................
Introduction
Product Introduction
Major Feature
6
6
...................................
........................................
Package Contents
Package Contents 7.....................................
Installation
WiFi Transmitter / Receiver installation order & how to install
PLC Transmitter / Receiver installation order & how to install
Operation checklist from LED status
Device with HDMI : Connect through HDMI port
How to install IR-Flasher
LAN Transmitter / Receiver installation order & how to install
11
12
13
14
15
16
........
........
.........................
................
.................................
........
Product Specication
Specication
Supported port
Video Format Supported
Audio Format Supported
Change WiFi Frequency
Factory Reset
Software upgrade
17
18
19
20
20
20
21
........................................
.......................................
................................
................................
.................................
........................................
.....................................
Q & A
Q & A 22.............................................
Operation Control & Function
Transmitter Front
Transmitter Rear
Receiver Front
Receiver Rear
Remote Control
8
8
9
9
10
.....................................
......................................
.......................................
........................................
......................................

English
Caution for Safety
4
Please read this user’s manual carefully before using the product.
If there is any strange sound, smoke or odor, pull the cable o immediately.
(It may cause re or electric shock)
Do not disassemble.
(It may cause re or electric shock.)
Do not put any sharpen object into the venting hole of the product.
(It may cause re or electric shock.)
Ensure to plug the product rmly.
(It may cause overheating or re if it plugs unstably.)
Ensure not to use the damaged cable.
( It may cause re or electric shock.)
Keep the product away from heaters or stoves.
(It may cause a re.)
Keep the battery of remote control out of reach of children.
Do not place the production on a bed, sofa or inside a closet that is not good for
ventilation.
(It may cause overheating or re.)
Do not use the product in close distance from the inammatory substance or combustible
spray.
(It may cause re.)

Caution for Safety
English
5
Always wipe the product o with soft fabric, not water mop.
(Water may come inside the product through the venting hole, and it may cause
electric shock.)
Keep clean the power plug and the outlet.
(Dirt may cause a short circuit and re.)
Keep the product out of reach of children.
Don’t unplug the power cord with a wet hand.
(It may cause electric shock.)
The heat and humidity may cause the damage to the remote control.
Unplug the power cord if you don’t use the product for a long time.
(Dirt may cause heat, re or electric shock.)
Ensure not to be damaged to the power cord.
(Damaged power cord may cause re or electric shock.)
Please use the devices in a stand position with stand cradle.
When you use the devices in laid down, it may cause the malfunction
of the devices because of the raise temperature of internal.
Don't place the devices near the heating product.
It may cause the malfunction of the devices because of the raise
temperature of internal.
Place the product 5cm apart from the wall for ventilation of heat.

Introduction
English
6
■ Product Introduction
■ Major Feature
●
●
●
●
●
●
●
1080p60 Full HD encoding/decoding with H.264 Baseline Prole (Level 4.2)
Low latency
- Latency of encoding-decoding in 1080p60 HD: Within 30ms
Supports both digital(HDMI) and analog(RGB, Component, D-Sub) video/audio
Supports Wireless or Wireline
- IEEE 802.11n 5 GHz WiFi
- Power line communication (PLC) modem
- LAN connection
Internal Antenna (Supporting MIMO)
HDMI-v1.3 (HDCP-v1.1) compliant.
Supports both DTV & VESA standards
- DTV : 1920x1080i60/p60, 1280x720p60, 720x480i60/p60
- VESA : WSXGA+(1680x1050), SXGA(1280x1024), WXGA(1280x800), XGA(1024x768),
SVGA(800x600), VGA(640x480)
itrio, using WiFi wireless solution, is the device for sending 1920x1080 Full HD video sources to other
location in your house. Once you connect Full HD video sources such as Set top box, Blu-ray player,
Multi media player, DVD player or PC to the transmitter and connect the display device to the receiver,
you can enjoy wirelessly Full HD video anywhere in your house.
itrio uses IEEE802.11n draft 2.0 standard WiFi technology for wireless connection. In case the wireless
connection is interfered, you can use PLC (power line communication) modem without additional
cable installation. You can also enjoy itrio through a LAN cable connection via LAN port.

Package Contents
English
7
■
※Before you use the product, check the following components are all present.
Transmitter Receiver Stand1 Stand2
■
Adapter1 Adapter2
Components
Adapter by model
PLC1 PLC2
Remote Control IR-Flasher
- HD-W100 / HD-L100
- HD-P100
User’s Manual Component adaptor

Operation Control & Function
English
8
■
■
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
Description Function
HDMI2-IN
AV-IN
IR-OUT
PC AUDIO-IN
2
3
4
5
HDMI 2 input port (correspond to ‘HDMI2’ on the remote control)
HDMI1-IN
1
HDMI 1 input port (correspond to ‘HDMI1’ on the remote control)
Composite or SCART input port (correspond to ‘AV’ on remote control)
PC-IN
6
Support component input through component gender.
It will be used for the following feature
Stereo Audio input port
DC
8
Power input port
Connect IR Flasher to control external devices which are connected to the
transmitter.
LAN
7
Power and
Source Button
Description Function
1
IR window
2
IR receiving window from remote control.
AV
3
4
PC
HDMI2
5
It will be on when the HDMI2 port is selected for the video input.
If the cable is not connected or video signal is not fed into properly, LED will blink.
6
HDMI1
It will be on when the HDMI1 port is selected for the video input.
If the cable is not connected or video signal is not fed into properly, LED will blink.
7
Power/Link LED
○
○
Press it shortly to turn the power on.
When power on,
-
-
Press shortly : Press to select the video input source. Each press the power
button will cycle through the available video input "HDMI1
→
MHMI2
→
PC
→
AV
→
HDMI1" in sequence.
Press longer : Press and hold more than 3 seconds to turn the power o.
○
○
○
Connection to PLC modem
Direct connection to LAN cable
Connection to PC for the system conguration setting
Transmitter Front
Transmitter Rear
It will be on when the AV-IN port (Composite or Scart) is selected for the video
input.
It will be on when the PC-IN port is selected for the video input.
If the cable is not connected or video signal is not fed into properly, LED will blink.
○
○
○
Blink : System booting or establishing link between the transmitter and the receiver.
Quick Blink : Software upgrading or wireless/LAN mode switching.
On : Finish of link establishment is completed between the transmitter and the
receiver.

Operation Control & Function
English
9
AUDIO-OUT 4
Connect additional IR Extender in order to extend receiving the
remote control.(purchase separately)
○
○
Press it shortly to turn the power on.
When power on,
-
-
Press shortly : Press to select the video input source. Each press the power
button will cycle through the available video input "HDMI
→
COMPO
→
AV
→
HDMI " in sequence.
Press longer : Press and hold more than 3 seconds to turn the power o.
■
■
Receiver Front
Receiver Rear
1
2
3
4
5
6
1
2
3
4
5
6
7
8
Description Function
AV-OUT
2
HDMI-OUT 1
HDMI output port
IR-IN
3
COMPONENT-OUT 5
Component output port
Stereo Audio output port
DC
8
Power input port
Composite or Scart output port
LAN
7
USB
6
This USB port is for software upgrade.
(For more information, please refer to Software upgrade on page 17. )
Power and
Source Button
Description Function
1
IR window
2
IR receiving window from remote control.
3
4
COMPO
5
HDMI It will be on when the HDMI-OUT port is selected for the video output.
6
Power/Link LED
○
○
○
Blink : System booting or establishing link between the transmitter and the receiver.
Quick Blink : Software upgrading or wireless/LAN mode switching.
On : Finish of link establishment is completed between the transmitter and the
receiver.
AV It will be on when the AV-OUT port (composite or SCART) is selected for the video
output.
It will be on when the COMPONENT-OUT port is selected for the video output.
LAN cable will be used for the following feature
○
○
○
Connection to PLC modem
Direct connection to LAN cable
Connection to PC for the system conguration setting

Operation Control & Function
English
10
12
5
4
3
68
7
■ Remote control
Description
Function
Display the current resolution, input / output ports, channel, WiFi reception (1/5~5/5). (5/5 strongest, 1/5 weakest)
It appears when you press and disappears automatically after around 20 seconds.
Note1. If the power is o abnormally, the user's conguration may not be saved.
Note 1.
Note 2.
Note 3.
Note 4.
⑥~⑧are functioned HD-W100 model only.
⑥~⑧are applied only when you press the button more than 5 seconds. On the normal link stage, if you change either TX or RX both device
will be changed simultaneously.
Otherwise you should change on TX and RX separately. (Info screen appears on the display for 3 seconds if it changes appropriately.
It will be rebooting when you change for ⑥~⑧. Power/Link LED will blink in a short time and reboot.
Link may be interfered caused by wrong setting or malfunction of ⑥~⑧button. In this case, please select desired communication mode
(LAN/WiFi) or channel to each transmitter and receiver using remote control.
INFO 2
AUDIO IN 5
VIDEO OUT 3
VIDEO IN 4
Select VIDEO input port on the transmitter (HDMI1, HDMI2, PC, AV)
Select VIDEO output port of the receiver (HDMI, COMPO , AV)
LAN(Red)
6
WiFi Ch1(Green)
7
WiFi Ch2(Yellow)
8
Select WiFi (Wireless) mode, Ch2.
* TX : Transmitter, RX : Receiver
Select WiFi (Wireless) mode, Ch1.
Select LAN (Cable) mode.
POWER
1
○
○
○
Power on :
- If you turn on TX or RX when power/Link LED is on , both devices will be power-on simultaneously within 10 seconds.
- You have to turn on each of TX and RX separately when power/Link LED is o, it may takes around 1 min 30 seconds for booting up.
Power o (press shortly) : When you turn o TX or RX, both devices will be power-o simultaneously and only power LED will be on.
Power o (press more than 4 sec) : When you turn o TX or RX, both devices will be power-o simultaneously, and LED will be o.
Power will be completely turned o.
To turn on/o the power of transmitter and receiver.
Select AUDIO input port on the transmitter (HDMI1, HDMI2, PC, AV)
Audio port is selected same with video port as a default. But you can select particular audio port using this button.

Installation
English
11
1)
2)
3)
4)
5)
6)
7)
8)
Connect external devices to TV.
Connect external devices to the transmitter through HDMI/COMPONENT/COMPOSITE port.
Attach the IR Flasher in front of IR window of external devices.
Connect the receiver to TV through HDMI/COMPONENT/COMPOSITE port.
Connect the power adapter of the transmitter.
Connect the power adapter of the receiver.
It would takes around 1 min30sec to be turned on.
Select the input port of the transmitter using either remote controller or button on the front of the device after
the system is on.
Select the output port of the receiver using either remote controller or button on the front of the device.
■ WiFi product
IR Flasher
External Device
TV1 TV2
Adapter Adapter
Transmitter Receiver
124
3
56
7
8

Installation
12
English
PLC PLC
1)
2)
3)
4)
5)
6)
7)
8)
Connect external devices to TV.
Connect external devices to the transmitter through HDMI/COMPONENT/COMPOSITE port.
Attach the IR Flasher in front of IR window of external devices.
Connect the receiver to TV through HDMI/COMPONENT/COMPOSITE port.
Connect the PLC adapter of the transmitter rst. Then, connect the power.
Connect the PLC adapter of the receiver rst. Then, connect the power.
It would takes around 1 min30sec to be turned on.
Select the input port of the transmitter using either remote controller or button on the front of the device after
the system is on.
Select the output port of the receiver using either remote controller or button on the front of the device.
■ PLC product
IR Flasher
External Device
TV1 TV2
Transmitter Receiver
12 4
3
7
8
56

Installation
13
English
External Device
TV2
Adapter
Adapter
Transmitter Receiver
1)
2)
3)
4)
5)
6)
Transmitter power/ LED o -> Please check the power connection
All LEDs of transmitter blink -> It would take around 1min 30sec for booting. Please unplug the power
adapter and connect again when it keeps blinking.
Input source LED of transmitter blink -> When there is no input source signal or input unsupported signal.
It needs to connect input source cable or change video resolution.
Power LED of receiver blinks -> When there is disconnection from the transmitter, because the distance
between transmitter and receiver is too far or malfunction of the PLC modem. Please locate transmitter and
receiver in near place and check the PLC operation.
All LED of receiver blink -> It would take around 1min 30sec for booting. Please unplug the power adapter
and connect again when it keeps blinking.
Output source LED of receiver blink -> Because of the dierentiation between output resolution and
resolution of output monitor, output is only supported with low resolution. It needs to be connected with
high resolution monitor.
■ Trouble shoot
2
1
35
4
6

Installation
14
English
■ Device with HDMI : Connect through HDMI port
TV2
HDMI
Receiver
External Device
TV1
Select HDMI1 or HDMI2
(Use the the remote controller or the front button on devices)
Transmitter
COMPONENT(YPbPr) Audio
COMPONENT(YPbPr)Audio
HDMI

Installation
15
English
IR Flasher
External Device1
IR Flasher
External Device2
IR Flasher
External Device3
Use remote controller of
external device
TV1
TV2
Receiver
Transmitter
■ How to install IR-Flasher
1)
2)
3)
Connect IR Flasher to IR-OUT of the transmitter.
Place the end point of IR Flasher to near IR window of multimedia players.
Control multimedia player remotely by pointing remote control of multimedia player to IR window
of the receiver.
From the receiver, you can remotely control the multimedia player which is connected to the transmitter.
13
2
You can connect up to
3 devices

Installation
16
English
1)
2)
3)
Connect LAN cable directly between the transmitter and the receiver, or to the IP router/LAN hub.
When you connect the transmitter and the receiver directly by UTP LAN cable, input the both end of
LAN cable to the each LAN port of the product. Then, turn the power on.
When you connect to the IP router/L2 switching hub, please follow the process below.
a.
b.
c.
d.
Please check the IP address of the device.
As a default conguration, transmitter’s IP address is 192.168.0.151, and receiver’s is 192.168.0.152.
The product has simple built-in web server inside. So, you can check and change the conguration. You can
connect the product to the PC via LAN cable and enter the IP address of the device on the web browser. At any
time, you can change the IP conguration as a default by factory set. (please refer to the Factory Reset on Page 16.)
When the default IP address of the transmitter/receiver are not used in your current network, just connect the
LAN cable to the IP router or LAN hub and turn the power on.
When the default IP address of the transmitter/receiver are already being used, you have to set the available IP
address to the transmitter and the receiver separately.
Connect the product to the PC via LAN cable, and enter new IP address of the transmitter/receiver respectively.
After setting new IP address, please follow the process.
For more information, please refer to the instruction at website (www.i-trio.com)
■ LAN model
LAN Cable
LAN Hub
Adapter
Receiver
Transmitter
Adapter
or or

Product Specication
17
English
■ Specication
Video Compression
System Latency
Digital Video IN/OUT Interface
Analog Video Input Interface
Analog Video Output Interface
Input Video Ports
Output Video Ports
Video Resolutions (partial list)
Digital Audio IN/OUT Interface
Analog Audio IN/OUT Interface
Analog Audio Transmission
Input Audio Ports
Output Audio Ports
Radio Power
Modulation
Frequencies Supported
Bandwidth
Antenna
Security
WPS
Ethernet LAN
IR in Transmitter
IR in Receiver
Power Supply
Dimensions (mm)
Weight (g)
Color
Operating Temperature
H.264 Baseline Prole Level 4.2
Less than 30 ms delay between Transmitter and Receiver
HDMI-v1.3 compliant, Up to 24 bit RGB or YUV (4:2:2)
RGB Video with D-Sub, Component Video Input, Composite Video Broadcast Signals (CVBS)
YPbPr Component, Composite Video Broadcast Signals (CVBS)
2 x HDMI, 1 x RGB Analog with D-Sub, 1 x CVBS with COMPOSITE
1 x HDMI, 1 x YPbPr RCA, 1 x CVBS with COMPOSITE
480i/p, 720p, 1080i and 1080p (24fps/30fps/60fps)
2 Ch Linear PCM, DTS 5.1 Ch., AC3 5.1 Ch.
Mini stereo headphone jacks
48 kHz sampling with 16bits resolution
2 x HDMI, 1 x Mini Stereo Headphone jack
1 x HDMI, 1 x Mini Stereo Headphone jack x CVBS with COMPOSITE
63mW (+18dBm)
IEEE 802.11n: OFDM
5.15 ~ 5.25 GHz
40 MHz
2T x 2R, 2 internal antenna
802.1x, 802.11i, WPA2, WPA and WEP 64/128 TKIP AES
Wireless Protected Setup for easy set up and security conguration
10/100 BASE-TX
12V/2.0A DC (US/EU standards, CE/FCC/UL certied)
28(W) x 195(H) x 103(D)
Transmitter : 270g , Receiver : 270g
White/Black
Operating from 0°C ~ 40°C
IR Receiver (front side) for itrio's IR Remote Controller
IR Flasher (rear side) for others' IR Remote Controller Blasting
IR Receiver (front side) for itrio's IR Remote Controller and
optional IR Extensive Receiver (rear side)

Product Specication
18
English
■ Supported port : How to make link between the transmitter and the receiver.
Transmitter
Component
(Multimedia Device)
* HDMI output is only available for the monitor supported 480i.
* COMPONENT output only supports some of resolution.
Please refer to video format supported of this user's manual (page19).
* COMPOSITE(AV) output only supports 1080i/576i/480i input.
* COMPOSITE(AV) output only supports 1080i/576i/480i input.
Receiver
HDMI1/HDMI2 input & Appropriate output port
Composite(AV) input & Appropriate output port
PC(D-Sub) input & Appropriate output port
Component(D-Sub) input & Appropriate output port

Product Specication
19
English
Note 1.
Note 2.
Note 3.
Note 4.
Note 5.
■ Video Format Supported
1600 x 1200p60 reduced format
itrio just relays the input format of the video from the transmitter to the receiver. itrio does not change the
video format. If you want to change output format, you should change input format on the external device
which is connected to the transmitter.
HDMI output of the receiver doesn't support AV(NTSC:480i or PAL:576i) input signal from the transmitter.
Please use component output terminal of receiver.
Among HDMI input signal, only 1080i/480i/576i input video signal support AV output. Other HDMI input
signal doesn't support AV output of the transmitter. Please use HDMI or Component output terminal of the
transmitter.
PC that is connected with D-Sub of the transmitter support only HDMI output of the receiver.
Video
Standard
VESA
Format
(PC standard)
DTV
Format
(TV standard)
Resolutions HDMI
640 x 480p60
640 x 480p70
640 x 480p85
800 x 600p60
800 x 600p70
800 x 600p85
1024 x 768p60
1024 x 768p70
1024 x 768p85
1152 x 864p60
1152 x 864p70
1152 x 864p85
1280 x 800p60
1280 x 960p60
1280 x 960p70
1280 x 960p85
1280 x 1024p60
1360 x 768p60
1440 x 900p60
1600 x 1200Rp60
1600 x 900p60
1680 x 1050p60
720 x 480I60(NTSC)
720 x 576I50(PAL)
720 x 480p60
720 x 576p50
1280 x 720p50
1280 x 720p60
1920 x 1080i50
1920 x 1080i60
1920 x 1080p24
1920 x 1080p25
1920 x 1080p30
1920 x 1080p50
1920 x 1080p60
D-SUB HDMI COMP
itrio Transmitter itrio Receiver
1)
AV(CVBS) AV(CVBS)
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
X
O
O
O
O
O
O
O
O
O
O
X
X
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
X
X
X
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
O
O
O
O
O
O
X
X
X
X
X
X
△
X
X
△
X
X
X
△
X
X
△
X
X
△
X
X
O
O
O
O
O
O
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
O
X
X
X
X
O
O
X
X
X
X
X

Product Specication
20
English
Change WiFi Frequency
Ch 1
Ch 2
5.19 GHz(WiFi Ch38)
5.23 GHz(WiFi Ch46)
WiFi Ch1 (Green)
WiFi Ch2 (Yellow)
WiFi Channel Frequency Use Remote Control Button
1)
2)
-Digital compressed audio : AC-3 Dolby Digital, DTS ( Pass Through)
Digital Audio
-16bit 2-channel linear PCM (44.1kHz & 48kHz)
Analog audio
1)
2)
3)
If there are the devices that use same WiFi frequency, the receiver’s output video may be
distorted because of frequency interference. In this case, you can change WiFi frequency in
order to avoid interference.
If you press the button (WiFi Ch1 / WiFi Ch2) of the remote control over 5 seconds, WiFi
frequency will be changed and system will be rebooted.
If the transmitter and the receiver are linked appropriately, it is ne to change WiFi frequency
on the one device. However, if the transmitter and the receiver are not linked, WiFi frequency
should be changed on each of transmitter and receiver respectively.
■
Factory Reset
1)
2)
With pressing the power button of the transmitter or the receiver, connect the power.
Once you press the power button for 3 seconds, all the LED will blink and the system setting is set
to be factory mode.
■
■ Audio Format Supported
This Function is applied to only wireless model(w).Note1.

Product Specication
21
English
1)
2)
3)
4)
5)
Download up-to-dated software (itrio.img) at web page (www.i-trio.com)
Store this S/W in "root directory" of USB memory.
Plug USB memory into the USB port of the receiver.
With LEDs blinking, the receiver and the transmitter will be upgraded in sequence.
(It takes around 5 minutes)
When the refreshing is completed, the product will be rebooted.
■ Software upgrade
a.
b.
c.
d.
Update is available only when the transmitter and the receiver operate normally.
NEVER remove the power during update.
(If the power is o during upgrading, the product will not work again.)
During the update, screen does not display the video.
When the product reboots again, you can remove the USB Memory.
Important Notice)