Philips Clon99-BKI User manual

Instructions for use
SMARTLOADER
Clon99-BK
3135 015 14061

2
Table of Contents..................................................................2
Safety/Precautions.................................................................2
Introduction...........................................................................2
Getting Started......................................................................3
Battery Installation................................................................3
Connecting the Clon99-BK Box...........................................4
Erasing Memory ...................................................................5
Reading Memory ..................................................................6
Programming (Writing) Memory to a TV............................7
Running a System Test .........................................................8
Exiting the Menu System .....................................................9
Programming with the On-Set Keyboard...........................10
On-Screen Displays for Non-Global TV using the
Transmitter..........................................................................11
On-Screen Displays for Non-Global TV using the On-Set
Keyboard.............................................................................12
Index ...................................................................................12
TABLE OF CONTENTS
Optimum Performance of
the Clon99-BK SmartLoader
box is obtained by plugging it
into an ITV set that is
already turned on.
For Customer Use:
Enter below the Serial No. which is located on
the product. Retain this information for future ref-
erence.
Model No
Serial No.
tThis “bolt of lightning” indicates uninsulated material
within your unit which may cause an electrical shock. For
the safety of everyone in your household, please do not
remove product covering.
s The “exclamation point” calls attention to features for
which you should read the enclosed literature closely to
prevent operating and maintenance problems.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE.
CAUTION: To prevent electric shock, match wide blade of
plug to wide slot, and fully insert.
ATTENTION: Pour éviter les chocs électrques, introduire
la lame la plus large de la fiche dams la borne correspon-
dante de la prise et pousser jussssqu'au fond.
ts
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
KNOW THESE SAFETY SYMBOLS
Assembling and operating your Philips Clon99-BK SmartLoader is designed to be an easy process. The purpose is to allow you to
more easily program a number of televisions using just a few simple steps.
The Clon99-BK SmartLoader replaces the RL-5180CK model. The Clon99-BK SmartLoader is compatible with all Philips
SmartPort and ClonPort TV sets including Global 1999 models from the PL9XXX, PC9XXX, and PA9XXX series.
Please be sure that you have the following material before beginning any procedures with the Clon99-BK SmartLoader box.
• A television capable of sending and receiving Clon99-BK SmartLoader information on TV settings.
• One 9-volt battery (for the Clon99-BK SmartLoader).
• Remote Control RG4172BK (T374AH).
• Three AA batteries for the remote control.
• Cable (6-conductor included with the Clon99-BK SmartLoader)
Please thoroughly read all the procedures listed within this booklet before starting any process.
Clon99™, SmartCard™, SmartLoader™, SmartPort™ ClonPort™ are registered trademarks of the Philips Consumer Electronics
Company. © 1999 Philips Consumer Electronics Company.
INTRODUCTION

3
1
2
3
GETTING STARTED
Remember. Always be sure
to check the polarity of the bat-
teries before inserting them in the
Clon99-BK SmartLoader or the
RG4172BK (T374AH) Remote
Control.
SMART HELP
BEGIN
CAUTION:
Failure to follow these instructions
may result in product damage. Please
read all instructions before beginning.
Battery installation
Clon99-BK SmartLoader
Before operating the Clon99-BK
SmartLoader, load a 9-volt battery
into the compartment in the bottom
of the Clon99-BK SmartLoader.
Slide the compartment lid in the
direction indicated by the triangle.
Plug the battery into the battery
cable, then place the battery in the
compartment.
Replace the compartment lid.
Battery installation
RG4172BK (T374AH)
Remote Control
Before operating the Remote
Control, please load the three AA
batteries into the compartment in the
bottom of the Remote Control.
Press the tab on the battery lid
and lift off the remote.
Following the diagrams inside the
Remote Control, load the batteries.
Then replace the battery lid. Point
the Remote Control at the TV and
see if it turns on the TV. If it does
not, repeat this step.
BEGIN
Clon99-BK SmartLoader Battery Installation
Slide the Battery Cover off the bottom
of the Clon99-BK SmartLoader
Attach and insert a 9 volt battery
Replace the Battery Cover
RG4172BK (T374AH) Remote Control Battery Installation
Press the tab on the Battery
Cover and lift it off. Load 3 “AA” volt batteries Replace the Battery Cover

4
SMART
PLUG
75Ω
ANT/
CABLE
POWER
1
2
4
EXTERNAL
SPEAKER
3
SMART
PLUG
75Ω
ANT/
CABLE
EXTERNAL
SPEAKER
CONNECTING THE CLON99-BK SMARTLOADER
Optimum Performance of the
Clon99-BK SmartLoader box
is obtained by plugging it into
an ITV set that is already
turned on.
Press the POWER button to turn
the ITV ON.
Plug one end of the cable into the
jack provided on the Clon99-BK
SmartLoader.
Plug the other end into the jack
provided on the back of the TV. The
TV’s jack is next to the Antenna
Input terminal and may be labeled
various ways such as; Smart Port,
Clone Port, etc.
Push the Slide Switch to the ON
position. The red LED should light.
(If the TV is turned off, it should
turn on within 15 seconds.)
Within 20 seconds, the Clon99-
BK SmartLoader on-screen display
should appear. If the display does not
appear, check the connections and
push the Slide Switch to the ON
position again. If there is still no
response from the SmartLoader,
replace its 9-volt battery.
Once the Clon99-BK
SmartLoader on-screen display
appears, press the POWER button on
the RG4172BK (T374AH) Remote
Control. The SmartLoader Setup
Menu should appear.
Clon99-BK SmartLoader Connection
Power button on the front of an ITV.
BEGIN
Clon99-BK
SmartLoader
Cable
Rear jack panel
of ITV
Clon99-BK SmartLoader
ON/OFF slider switch
LED
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
5
6
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Stored Memory Type 01, 04
LIGHT
SLEEP
CH
RECALL
POWER
SELECT
123
456
789
0
POWER
GUEST SETUP SETUP
VOL
M
~
!
A/CH
MUTE
CC
RESET
C D G D E
TV
TV DCM
F
EG
C
BD
A
6
Press the POWER button
on the remote control.
Clon99-BK SmartLoader
On-Screen Display Clon99-BK SmartLoader
Setup Menu

5
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Stored Memory Type 01, 04
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Erase? Press 0 to confirm
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Memory Erased
1
2
3
-
VOL CH
123
456
789
0
S
E
L
E
C
T
M
SLEEP
A/CH
MUTE
POWER
+
CC
RECALL
RESET
CH GDE
GUEST SETUP SETUP
TV TV DCM
ABCD
EFG
1
2
3
4
ERASING MEMORY OR DATA
ERASE MEMORY
To read and save the television mem-
ory, it is first necessary to erase any
currently saved data in the Clon99-
BK SmartLoader. If the “Stored
Memory Type” indicates no data is
saved currently, you may bypass the
ERASE MEMORY operation and
move directly to the READ MEMORY
operation.
With the Clon99-BK SmartLoader
on-screen display showing, press the
POWER button on the remote control
The Setup Menu will appear.
Press the Number 4 button on the
Remote Control to select the 4th
option “Erase SmartLoader Memory.”
The screen will ask “Erase?”
Press the 0 button on the remote to
confirm and begin the procedure.
The screen will indicate “Memory
Erased” when the data has been
erased for the Clon99-BK
SmartLoader.
BEGIN

6
SMART
PLUG
75Ω
ANT/
CABLE
EXTERNAL
SPEAKER
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Stored Memory Type 01, 04
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Read? Press 0 to confirm
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Reading Block 23 of 63
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Finished Reading Memory
1
2
-
VOL CH
123
456
789
0
S
E
L
E
C
T
M
SLEEP
A/CH
MUTE
POWER
+
CC
RECALL
RESET
CH GDE
GUEST SETUP SETUP
TV TV DCM
ABCD
EFG
1
2
3
4
5
3
6
READ MEMORY
Once the memory has been erased, the
Clon99-BK SmartLoader is ready to
read a television’s memory. Follow the
steps below to complete the procedure.
With the Clon99-BK SmartLoader
on-screen display showing, press the
POWER button on the remote control.
The Setup Menu will appear. Press
the Number 1 button on the Remote
Control to select the first option “Read
TV.”
The on-screen display will ask,
“Read?” Press the 0 button to confirm
and begin the Read procedure.
The on-screen menu will reading
blocks of data on the bottom of the dis-
play.
Once the “Read” procedure is com-
plete, “Finished Reading Memory” will
appear at the bottom of the display.
Disconnect the SmartLoader cable
from the back of the TV to complete
the “Read TV” operation or another
Numbered button to choose a different
option.
BEGIN
READING MEMORY OR DATA

-
VOL CH
123
456
789
0
S
E
L
E
C
T
M
SLEEP
A/CH
MUTE
POWER
+
CC
RECALL
RESET
CH GDE
GUEST SETUP SETUP
TV TV DCM
ABCD
EFG
SMART
PLUG
75Ω
ANT/
CABLE
EXTERNAL
SPEAKER
1
2
6
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Stored Memory Type 01, 04
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Write? Press 0 to confirm
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Writing Block 23 of 63
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Finished Writing Memory
3
8
4
5
7
7
PROGRAMMING A TELEVISION’SINTERNAL MEMORY
WRITING TV MEMORY
After the Memory has been read from
one television, the Clon99-BK
SmartLoader is now ready to write the
memory to other televisions. This mem-
ory can be written with or without cer-
tain settings. These settings include:
Picture Adjustment, Minimum and
Maximum Volume, and the On Volume
settings.
Plug one end of the cable into the
jack provided on the SmartLoader. Then
plug the other end into the jack provided
on the back of the TV. The TV jack is
next to the Antenna Input terminal.
Push the Slide Switch to the ON
position on the SmartLoader. If the TV
is currently off, it should turn on within
15 seconds.
Within 20 seconds, the SmartLoader
on-screen display should appear on the
TV screen. If the display does not
appear, check connections and push the
Slide Switch to the ON position again.
If there is still no response from the
SmartLoader, replace its 9-volt battery.
Press the POWER button on the
remote to display the Clon99-BK
SmartLoader Setup Menu.
With the Setup Menu visible, press
the Number 2 button on the Remote
Control to select the 2nd option “Write
TV With Settings” or press the Number
3 button to select the third option
“Write TV Without Settings.”
The screen will ask “Write?” Press
the 0 button on the remote to confirm
and begin the procedure.
The screen will indicate “Writing
Block 24 of 63” while the Clon99-BK
SmartLoader is downloading the data.
The display will then read
“Finished Writing Memory” when the
procedure has been completed.
BEGIN
Typical rear jack
panel of ITV
Clon99-BK SmartLoader Box
ON/OFF Slide Switch
LED

8
-
VOL CH
123
456
789
0
S
E
L
E
C
T
M
SLEEP
A/CH
MUTE
POWER
+
CC
RECALL
RESET
CH GDE
GUEST SETUP SETUP
TV TV DCM
ABCD
EFG
3
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Stored Memory Type 01, 04
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Test? Press 0 to confirm
SmartLoader 99
System Test
Press 1 to Continue
1
2
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Display Registration
12 Rows by 32 Columns
0123456789012345678901
Press 1 to Continue
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Character Set Display
!"#$%&'()*+,-./01234
56789:;<=>?@ABCDEF
GHIJKLMNOPQRSTUV
WXYZ abcdefghijklmno
Press 1 to Continue
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Check +12V Power Supply
12V Detected
Press 1 to Continue
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
IR Test
Press A/CH to Continue
Press 1 to Skip
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
IR Test
A/CH detected, IR good
Press 1 to Continue
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Test Finished
Press 1 to Continue
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4
54
RUNNING A SYSTEM TEST
SYSTEM TEST
A System Test of the Clon99-BK
SmartLoader can be preformed by fol-
lowing the steps below.
With the Clon99-BK SmartLoader
on-screen display showing, press the
POWER button on the remote control
The Setup Menu will appear.
Press the Number 5 button on the
Remote Control to select the 5th
option “System Test.”
The screen will ask “Test?” Press
the 0 button on the remote to confirm
and begin the procedure.
As the System Test proceeds, the
display will prompt the user to press
the Number 1 button or the A/CH
button to continue or skip to the next
part of the test.
When the display shows “Test
Finished,” press the Number 1 button
to return to the Clon99-BK
SmartLoader Setup Menu.
BEGIN

9
SMART
PLUG
75Ω
ANT/
CABLE
EXTERNAL
SPEAKER
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Stored Memory Type 01, 04
Philips SmartLoader 99
System Version D.0
1 - Read TV
2 - Write TV With Settings
3 - Write TV Without Settings
4 - Erase SmartLoader Memory
5 - System Test
6 - Exit SmartLoader
Exit? Press 0 to confirm
Power Down Mode
1
2
-
VOL CH
123
456
789
0
S
E
L
E
C
T
M
SLEEP
A/CH
MUTE
POWER
+
CC
RECALL
RESET
CH GDE
GUEST SETUP SETUP
TV TV DCM
ABCD
EFG
1
2
3
4
3
5
EXITING THE CLON99-BK SMARTLOADER MENU
EXIT SMARTLOADER
When you have completed all the pro-
cedures you wish to preform, exiting
the Clon99-BK SmartLoader and shut-
ting down is simple.
With the Clon99-BK SmartLoader
on-screen display showing, press the
POWER button on the remote control
The Setup Menu will appear.
Press the Number 6 button on the
Remote Control to select the 6th
option “Exit SmartLoader.”
The screen will ask “Exit?” Press
the 0 button on the remote to confirm
and begin the procedure.
The Clon99-BK SmartLoader
will display a screen that reads
“Power Down Mode” then shut itself
off.
When finished, unplug the
Clon99-BK SmartLoader from the
rear jack panel of the television.
BEGIN

10
SMART
PLUG
75Ω
ANT/
CABLE
EXTERNAL
SPEAKER
PHILIPS
SMARTLOADER 99
Copyright PCEC 1999
System Version D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
Philips SmartLoader 99
System Version D.0
Press CH/UP to Write TV
Press Power to Exit System
Stored Memory Type 01, 04
Philips SmartLoader 99
System Version D.0
Press CH/UP to Confirm Write
Press CH/DN to Abort
Press Power to Exit System
Stored Memeory Type 01, 04
Philips SmartLoader 99
System Version D.0
Writing Block 23 of 63
Philips SmartLoader 99
System Version D.0
6STEREO
INSTALL/
MENU
– VOLUME + CHANNEL
POWER
MENU
– VOLUME + CHANNEL
POWER
45
6
8
3
2
1
Press CH/UP to Confirm Write
Press CH/DN to Abort
Press Power to Exit System
Finished Writing Memory
Press CH/UP to Confirm Write
Press CH/DN to Abort
Press Power to Exit System
PROGRAMMING ATELEVISION WITH THE ON-SET KEYBOARD
WRITING TV MEMORY
WITH THE ON-SET KEYBOARD
After the Memory has been read from
one television, the Clon99-BK
SmartLoader is now ready to write
the memory to other televisions. The
following steps show how to down-
load or “write” memory from one
television to another using the On-Set
Keyboard.
Plug one end of the cable into the
jack provided on the SmartLoader.
Then plug the other end into the jack
provided on the back of the TV. The
TV jack is next to the Antenna Input
terminal.
Push the Slide Switch to the ON
position on the SmartLoader. If the
TV is currently off, it should turn on
within 15 seconds.
Within 20 seconds, the
SmartLoader on-screen display
should appear on the TV screen. If
the display does not appear, check
connections and push the Slide
Switch to the ON position again. If
there is still no response from the
SmartLoader, replace its 9-volt bat-
tery.
Press the POWER button on the
front of the TV to display the
Clon99-BK SmartLoader “Write TV”
Menu.
Press the CH/UP button on the
front of the TV to write the memory
to the television.
The screen will ask “Press
CH/UP to Confirm Write,” “Press
the CH/DN to Abort,” or “Press the
Power to Exit System.” Press the
CH/UP button to confirm and begin
the procedure.
The screen will indicate “Writing
Block XX of XX” while the Clon99-
BK SmartLoader is downloading the
data.
The display will then read “Finished
Writing Memory” when the proce-
dure has been completed.
Press the Power button on the
front of the TV to EXIT the system.
BEGIN
Typical rear jack
panel of ITV
Clon99-BK SmartLoader Box
ON/OFF Slide Switch
LED

11
CLON99-BK SMARTLOADER DISPLAYS USING
PROGRAMMING TRANSMITTER FOR NON-GLOBAL TV
PHILIPS
SMART LOADER
SYSTEM REVISION D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
PHILIPS
SMART LOADER
SYSTEM REVISION D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
PHILIPS
SMART LOADER
SYSTEM REVISION D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
PHILIPS
SMART LOADER
SYSTEM REVISION D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
PHILIPS
SMART LOADER
SYSTEM REVISION D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
TELEVISION TYPE - -
SAVED DATA TYPE - -
0 - EXIT 1- READ TV
2 - WRITE TV - PIC
3 - WRITE TV - NO PIC
4 - ERASE
5 - TV/BUS SYSTEM TEST
EXIT SMART LOADER SYSTEM
?? ARE YOU SURE??
1 - EXIT SMART LOADER
0 - RETURN TO MENU
TELEVISION TYPE - -
SAVED DATA TYPE - -
0 - EXIT 1- READ TV
2 - WRITE TV - PIC
3 - WRITE TV - NO PIC
4 - ERASE
5 - TV/BUS SYSTEM TEST
TELEVISION TYPE - -
1 - READ TV MEMORY
0 - RETURN TO MENU
TELEVISION TYPE - -
?? ARE YOU SURE ??
1 - READ TV MEMORY
0 - RETURN TO MENU
READING BLOCK - -
TV MEMORY READ
AND SAVED
TELEVISION TYPE - -
SAVED DATA TYPE - -
0 - EXIT 1- READ TV
2 - WRITE TV - PIC
3 - WRITE TV - NO PIC
4 - ERASE
5 - TV/BUS SYSTEM TEST
TELEVISION TYPE - -
SAVED DATA TYPE - -
1 - WRITE TV MEMORY
0 - RETURN TO MENU
TELEVISION TYPE - -
SAVED DATE TYPE - -
?? ARE YOU SURE ??
1 - WRITE TV MEMORY
0 - RETURN TO MENU
WRITING BLOCK - -
MEMORY WRITE COMPLETE
TELEVISION TYPE - -
SAVED DATA TYPE - -
0 - EXIT 1- READ TV
2 - WRITE TV - PIC
3 - WRITE TV - NO PIC
4 - ERASE
5 - TV/BUS SYSTEM TEST
SAVED DATA TYPE - -
1 - EARSE MEMORY DATA
0 - RETURN TO MENU
SAVED DATA TYPE - -
?? ARE YOU SURE ??
1 - ERASE MEMORY DATA
0 - RETURN TO MENU
DATA ERASURE COMPLETE
TELEVISION TYPE - -
SAVED DATA TYPE - -
0 - EXIT 1- READ TV
2 - WRITE TV - PIC
3 - WRITE TV - NO PIC
4 - ERASE
5 - TV/BUS SYSTEM TEST
TV/DATA TERMINAL
SYSTEM TEST SEQUENCE
1 - CONTINUE TEST
0 - RETURN TO MENU
*DISPLAY REGISITRATION*
1 - CONTINUE TEST
0 - RETURN TO MENU
10 LINES/26 CHARACTERS
DOWNLOAD CHARATER SET
!"#$%^'[]*+,-./0123
456789;^<=>?/ABCDEFG
HIJKLMNOPQRSTUVWXYZ
1 - CONTINUE TEST
0 - RETURN TO MENU
*
*
*
*
*
*
*
**
IR DATA LINK TEST
PRESS A/CH ON TRANSMITTER
1 - CONTINUE TEST
0 - RETURN TO MENU
TEST DATA TERMINAL POWER
NO POWER SUPPLY DETECTED
1 - CONTINUE TEST
0 - RETURN TO MENU
NO INTERNAL TELEVISION
ERRORS DETECTED
1 - TEST COMPLETE
Follow these screens when choosing option “0” - EXIT.
Follow these screens when choosing option “1” - READ TV.
Follow these screens when choosing option “2” or “3” - WRITE TV - PIC, or WRITE TV - NO PIC.
Follow these screens when choosing option “4” - ERASE.
Follow these screens when choosing option “5” - TV/BUS SYSTEM TEST.

12
INDEX
Battery Installation - Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Battery Installation - Clon99-BK SmartLoader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Erase Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Exiting the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
On-Set TV Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10, 12
On-Screen Displays for Non-Global TV with Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
On-Screen Displays for Non-Global TV with On-Set Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Programming with On-Set Keyboard for Global TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Programming (Writing) Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Read Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3, 5-9
Safety/Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
CLON99-BK SMARTLOADER DISPLAYS USING
ON-SET KEYBOARD WITH NON-GLOBAL TV
TELEVISION TYPE - -
SAVED DATA TYPE - -
CH/UP - WRITE TV MEMORY
PHILIPS
SMART LOADER
SYSTEM REVISION D.0
PN 3135 019 01681
PRESS POWER TO BEGIN
TELEVISION TYPE - -
SAVED DATA TYPE - -
?? ARE YOU SURE ??
CH/UP - WRITE TV MEMORY
CH/DN - DO NOT WRITE
MEMORY WRITE COMPLETE
WRITING BLOCK - -
NO DATA SAVED FOR
TELEVISION TYPE - -
TV PRODUCT TYPE - -
POWER CH/UP
CH/UP CH/DN