awave DSP 6-8 User manual

PRODUCT BRIEF INTRODUCTION
[ 11 ]
PRODUCT BRIEF INTRODUCTION
[ 12 ]
1.DSP interface guidance
7.2 Interface introduction
1
2
3
4
5
6
7
1. Connect(connect to the DSP)
1
2. FILE MAIN MENU
8
9
10
11
5. Save as(To save another file settingto PC)
3. Open(Toload preset file in PCfolder)
4. Save(To save setting toPC)
6. Restore Factory(To save preset file in DSP)
7.Modify Password
8. Write To Device
9. Read From Device
11. Exit
3. INPUT MODE.
To selectdifferent input devices.
10. About
2. Language(choose you need language)
CH mode(2CH 4CH 6CH MIX).
1
4. CHANNAL SETING.
2Input channel:FL. FR. FL. FR. RL.RR. SUB L. SUB R.
When you click the drop-downbutton, you can choose thestate of the channelinput.
There is : FR. FL.RR. RL. SUB R. SUBL.M1=FL+FR.M2=FL+RL.M3=FR+RR.
M4=FL+RL+SUBL.M5=FR+RR+FUBR.

PRODUCT BRIEF INTRODUCTION
[ 13 ]
PRODUCT BRIEF INTRODUCTION
[ 14 ]
M1=FL+FR. M2=FL+FL. M3=FR+FR. M4=FL+RL+SUBL. M4=FR+RR+SUBR.
Options on the Link arefor combine setting for Left CH and RightCH .
Options on the Left CH/rightCH allow you tone eachselected channel respectively.
5. CROSSOVER X-TPE.
To choosedifferent crossovertype, for example select CH selection on 3RD
spot .that would locate CH you wantto choose for crossover configuration .
6. CROSSOVER FREQUENCY.
Set frequency of LP/HP individually .
7. GAIN.
0--40dB is optional range for gain control kfevery CH.
8. DELAY.
1.Auto configuration(base on 1.5setting).
2.Manual configuration, change specificationsin selected CH manually.
9. LP/SLOPE.
1.6dB/oct 12dB/oct 18dB/oct 24dB/oct 30dB/oct
36dB/oct. 42dB/oct 48dB/oct areavailable.
10. HP/SLOPE.
1.6dB/oct 12dB/oct 18dB/oct 24dB/oct 30dB/oct
36dB/oct.42dB/oct 48dB/oct are available.
3Output channel:FL FullRange.FR FullRange.
When you click the drop-downbutton, you can choose thestate of the channelinput.
There is : Null.Front.Rear.Center.Subwoofer and Full.Tweeter.Mid-T.Midrange.M-WF. Woofer.

PRODUCT BRIEF INTRODUCTION
[ 15 ]
PRODUCT BRIEF INTRODUCTION
[ 16 ]
8.STAND INSTALLATION REFERENCE
8.1 5 CHANNEL STAND ALONE TREBLE MODE
8.2 5 CHANNEL PASSIVE X-OVER TREBLE MODE
HuHu
++--
Hi Level inputHi Level input
12+12+
GroundGround
AccuAccu
Rem OutRem Out
Front1/A+B To ModbassFront1/A+B To Modbass
Front2/C+D To TweeterFront2/C+D To Tweeter
Subwoofer/G+H To SubwooferSubwoofer/G+H To Subwoofer
LTWLTW
RTWRTW
LMBLMB
RMBRMB
4 ch Amp4 ch Amp
Rem InRem In
Relay 12+Relay 12+
Rem InRem In
Monoblock/Monoblock/
2ch Amp2ch Amp
SubwooferSubwoofer
GroundGround
Front1/A+B To FrontSpeakerFront1/A+B To FrontSpeaker
Front2/A+B Or Rear E+F To Rear SpeakerFront2/A+B Or Rear E+F To Rear Speaker
Subwoofer/G+H To SubwooferSubwoofer/G+H To Subwoofer
HuHu
Low Level inputLow Level input
RemRem
12+12+
++--
ACCUACCU
RelayRelay
Passive X-OverPassive X-Over
4Ch4Ch
SubwooferSubwoofer
Mono/2ChMono/2Ch
Rem OutRem Out
Rear SpeakerRear Speaker
Rear SpeakerRear Speaker
Front SpeakerFront Speaker
CoaxialCoaxial
14. X-OVER AND EQ CHARTS.
15. EQ SETTING.
1.Red lines and slopes will change accordingly when
2.EQ all frequency pointscan be move leftor right.For 20Hz-20KHz can be any Regulation.
Q volue=1-12.
HP/LP of crossover and EQ are modified.
12. WRITE.
To Write ToDevice(POS1-POS8).
11. Filter Model.
To choosedifferent Filter typeLinkwitz Bessel Butterworth.
13. READ.
To Read From Device(POS1-POS8).

PRODUCT BRIEF INTRODUCTION
[ 17 ]
PRODUCT BRIEF INTRODUCTION
[ 18 ]
8.3 8 CHANNEL SEPARATE TREBLE,MIDDLE MODE
9.REMOTE INTRODUCTION
10.TECHNICAL FEATURES
POWER SUPPLY
Voltange 9.0-15VDC
Idling current 0,5A
5mm
Switched off with DRC 4mA
Remote IN voltage 6-15 VDC
Remote OUT voltage 12 VDC(130mA)
Switched off without DRC
SIGNAL STAGE
Distortion - THD @ 1kHz, 1V RMS Output 0,0004%
Bandwith @-3 dB 20-22kHz
Master Input 98 dBA
Auxinput 96dBA
Channel Separation @ 1 kHz 90 dB
S/N ratio @ A weighted
Input Sensitivity(Speaker In) 2-15 V RMS
Input Sensitivity(Aux In) 0,2-5 V RMS
Input Sensitivity(Phone)
Input Sensitivity(Speaker In) 10kÙ
Input Sensitivity(Aux) 22kÙ
Input Sensitivity(Phone)
Max OUTPUT Level(RMS) @ 0.1% THD 4 V RMS
INPUT STAGE
High Level(Speaker) FL-FR-RL-RR-SUBL-SUBR,Phone IN
Low level(Pre) FL-FR-RL-RR-SUBL-SUBR, AUX IN
OUTPUT STAGE
Low level Pre(default) Midrange(A+B)/Midbass(E+F)/Subwoofer(G+H)
CONNECTION
From/To Personal Computer 1 x USB/B(1.1/2.0) 5M
CROSSOVER N.5(one each output channel)
Filter Type Full/High/Low Pass /Band Pass
Slope Setting 6/12/18/24/30/42/48 dB
68 steps @ 20- 20kHz
Phase control indepent setting for each channel 0 - 180
Crossover frequency
SubwooferSubwoofer
GroundGround
Front1/A+B To MidrangeFront1/A+B To Midrange
Subwoofer/G+H To SubwooferSubwoofer/G+H To Subwoofer
HuHu RemRem
12+12+
++--
ACCUACCU
RelayRelay
Rem OutRem Out
4Ch/Power4Ch/Power
Mid bassMid bass
4Ch/Power4Ch/Power
TWTW
MidrangeMidrange
Front1/C+D To TweeterFront1/C+D To Tweeter
Rear/E+F To MidbassRear/E+F To Midbass