Axiom Audio SW36XFA User manual

USER MANUAL
SW36XFA
acve subwoofer
KEY FEATURES
• Very High Output • Manifolded Band Pass conguraon for very high output in compact size
• High-strength, water repellent, glass ber reinforced cones • Tetracoil® dual voice coil for extended linear response and increased power handling
• Digitally controlled Class D amplier module with SMPS • 96KHz / 40 bit oang point CORE processing with PRONET remote control
INTRODUCTION
The SW36XFA subwoofer is designed to deliver high quality low frequency reproducon
where very high output is a key requirement, together with well dened deep bass response
and fast transient response. Its compact size and light weight make it suitable for several
dierent uses, ranging from touring applicaons to xed installaons and high-level dance
clubs.
The SW36XFA is a very high quality powered subwoofer system featuring some of the most
advanced technologies for low frequency reproducon. Its unique and innovave design is
based on a conguraon that can be dened as Manifolded Band Pass.
It uses manifolding of the front side of the cones to maximize the mutual coupling between
the two drivers. This innovave conguraon does not use any large resonant cavity to load
the speaker, but very compact cavies in order to obtain advantages in terms of denion,
both at the lowest end and the upper bass.
The SW36XFA subwoofer system is equipped with two high power 18” (460mm) transducers
capable of very long excursion (up to 30mm peak-to-peak), and featuring a a large
displacement suspension system. These transducers use Tetracoil technology, where two
dierent, axially separated magnec gaps and two inside-outside 100mm (4” ) diameter
voice coils are wound on the same former and suspended evenly in the two magnec gaps.
This creates an equivalent voice coil diameter greater than 6”, resulng in a larger heat
dissipaon area for and increased power handling. Addional key advantages of the Tetracoil technology are also minimized distoron and a very
symmetric and at inductance curve. Cones are made of very high-sness berglass reinforced paper, featuring also invisible water repellent
treatment. The SW36XFA is processed by 40bit, 96kHz oang point CORE DSP and powered by DA SERIES digital power modules. The DA module
employed for powering the SW36XFA delivers in an ultra-compact package a maximum power of 4000W and features PFC (Power Factor Correcon),
a technology able to guarantee always the highest level of power regardless of any eventual uctuaons of the power supply.
TECHNICAL SPECIFICATION
Acouscal Amplier Type Class D with Variable Switching Frequency
and SMPS and PFC and PFC
System type Manifolded Band Pass
Transducer
Two 18” (460 mm), 100mm (4in) Tetracoil®
dual voice coil, equivalent to a single coil
diameter larger than 152mm (>6in).
Water repellent cone and epoxy coated
plates.
Ultra linear suspension behavior.
Mains Voltage Range (Vac) 100-240 V~ 50/60 Hz
Mains Connector PowerCon TRUE1 - NAC3PX (In/Out)
Consumpon* 600 W (nominal) 1800 W (max)
IN / OUT Connectors Neutrik XLR-M / XLR-F
IN / OUT Network Connectors ETHERCON® (NE8FAV)
Frequency response (±3 dB) 36 Hz – 100 Hz (Processed) Mechanical
Maximum Peak SPL @ 1m 143 dB Width 746 mm (29.4”)
Electrical Height 795 mm (31.3”)
Input Impedance 20 kΩ balanced Depth 710 mm (27.9”)
Input Sensivity +4 dBu / 1.25 V Depth Including Wheels 838 mm (32.9”)
Signal Processing CORE processing, 96kHz / 40bit oang
point SHARC DSP, 24 bit AD/DA converters
Construcon 15 mm, reinforced Phenolic Birch
Paint High resistance, water based paint
Direct access Controls 4 Presets: Standard, InfraSub, Cardioid,
User. Network Terminaon, GND Link
Wheels 4 heavy-load 100 mm ø (oponal)
Transport 6 handles
Remote Controls PRONET control soware Net Weight 91.2 Kg (201.1 lbs.) without wheels
Network protocol CANBUS
Output Power 2000 W + 2000 W
* Nominal consumpon is measured with pink noise with a crest factor of 12
dB, this can be considered a standard music program.
revision 2015-09-30

MECHANICAL DRAWING
74.6 cm
29.4"
71.0 cm
27.9"
79.5 cm
31.3"
83.8 cm
32.9"
F F
F
F
FF
F = Flying Points
T = Feet for floor or stacking installaons
T

OPTIONAL ACCESSORIES
KPTSW36 Fly bar for Axiom SW36XF and AX2010 Loudspeakers
AC103GS 100 mm Swivel castor without brake
NAC3FXW Neutrik Powercon® TRUE1 (for power in) Note:
See assembly instrucon downloadable from NEUTRIK WEB
site at: hp://www.neutrik.com/
NAC3MXW Neutrik Powercon® TRUE1 (for power out)
HTAC Hand tool for ghtening the bushing of the powerCON TRUE1
CAT5SLU01/05/10 LAN5S - Cat5e - RJ45 plugs and NE8MC1 connectors. 1/5/10 m Length
AR100LUxx Hybrid cable 1x Cat6e - 1x Audio with NEUTRIK connectors 0.7/1.5/2.5/5/10/15/20 m Length
AR200LUxx Hybrid cable 1x Cat6e - 2x Audio with NEUTRIK connectors 20/30/40/60/80 m Length
AVCAT5PROxx Cat5e on cable drum, RJ45 plugs and NEUTRIK connectors 30/50/75 m Length
NE8MCB Neutrik Ethercon PLUG
NC3MXXBAG Neutrik XLR-M
NC3FXXBAG Neutrik XLR-F
USB2CAN PRONET network converter
USB2CAND PRONET network converter with dual RJ45 outputs
RAINCOV215 Rain cover for input sockets
AXFEETKIT Kit made of 6pcs BOARDACF01 foot
see hp://www.axiomproaudio.com/ for detailed descripon and other available accessories.
SPARE PARTS
AC103GS 100 mm Swivel castor without brake
95AXM014 Locking Pin for AX2010
98AXM218TLW4 18’’ woofer - 4” Tetracoil® dual voice coil - 4 ohm
NAC3PX Neutrik Powercon® TRUE1 Appliance inlet-outlet combinaon
SCNACPX Neutrik Rubber Sealing for NAC3PX
91AMDSW36 SW36XFA Amplier module assembly

POWER INPUT
MAINS~ IN - Powercon® NAC3PX power inlet connector. To switch the amplier on, insert
the Powercon® connector and turn it clockwise into the ON posion. To switch the amplier
o, pull back the switch on the connector and turn it counter-clockwise into the POWER
OFF posion.
MAINS~ OUT - Powercon® NAC3PX power outlet connector. This is connected in parallel
with the MAINS~ IN.
WARNING! Connect no more than one subwoofer unit to the MAINS~ OUT
connector.
WARNING! If you use the MAINS~ OUT turn on each subwoofer unit one a me.
WARNING! In the case of product failure or fuse replacement, disconnect the unit
completely from the mains power.
WARNING! Use a suitable power cable and mains plug to build the power cable, it
must only be connected to a socket corresponding to the specicaons indicated
on the amplier unit.
See assembly instrucon downloadable from NEUTRIK WEB site at: hp://www.
neutrik.com/
CONTROL PANEL
ON - This LED indicates power on status.
PROT - This red LED lights when the amplier module is in protect mode for an internal fault
and, consequently, the amplier is muted.
SIGN LIMIT - This LED lights in green to indicate the presence of the signal and lights in red
when an internal limiter reduces the input level.
INPUT - Audio signal input with locking XLR connector. It has a fully electronically balanced
circuitry including AD conversion for the best S/N rao
and input headroom.
LINK - A direct connecon from the input connector to
link other speakers with same audio signal.
GND LIFT - This switch li the ground of the balanced
audio inputs from the earth-ground of the amplier
module.
PRESET BUTTON - This buon has two funcon:
1) Pressing it while powering on the unit:
ID ASSIGN the internal DSP assigns a new
ID to the unit for the PRONET
remote control operation. Each
loudspeaker must have a unique
ID to be visible in the PRONET
network. When you assign a new
ID, all the other loudspeakers with
the ID already assigned must be ON
and connected to the network.
2) Pressing it with the unit ON you can select the
DSP PRESET. The selected PRESET is indicated by
the corresponding LED:
STANDARD This PRESET is suitable for any
applicaon where low frequency
reinforcement is required. It
features a 90Hz cut o frequency
and it can be used in almost any
environment in combinaon with
any vercal arrays.
INFRA This PRESET can be used when a
deeper bass response is required
(Note that when this preset is
used the sound pressure level of
the system is slightly reduced).
NOTE: INFRA and STANDARD
PRESET must NOT be used
together in close units.
CARDIOID This special PRESET, combined
with the STANDARD PRESET, gives
the advantage to reduce the low
frequencies at the back of an
array of three subs, in order to
+15
+10
+5
0
-5
-10
-15
-20
-25
-30
-35
20 50 100 200 500 1K 2K 5K 10K 20K Hz
SW218A - PRESET RESPONSE
INFRA
STANDARD

obtain a more comfortable level for the performers on the stage without losing level for the the audience in front of the array.
The cardioid conguraon is also useful in situaon where you want to reduce the bass frequency feedback due to many
microphones on stage, for example for acousc and jazz ensemble, classic orchestra, musicals. Further in this manual you can
nd some example how to set up a cardioid array.
USER This LED lights when the USER PRESET is loaded. This preset corresponds to USER MEMORY no. 1 of the DSP and, as a factory
seng, it’s the same to STANDARD. If you want to modify it, you have to connect the unit to a PC, edit the parameters with
PRONET soware and save the PRESET into USER MEMORY no. 1.
NETWORK IN/OUT - These are a standard RJ45 CAT5 connectors (with oponal NEUTRIK NE8MC RJ45 cable connector carrier), used for PRONET
network transmission of remote control data over long distance or mulple unit applicaons.
TERMINATE - In a PRONET network the last loudspeaker device must be terminated (with an inner load resistance) especially in a long run cabling:
press this switch if you want to terminate the unit.
POWER AMPLIFIERS
The SW36XFA is powered by DA SERIES digital power modules, a new generaon of CLASS D power amplier with digitally-controlled SMPS.
The innovave technology used for these ampliers (including also the use of a variable switching frequency) oers performances at the top of
the range, such as a superior sound denion at any audio frequency, very high dynamics also for low level signals and very low distoron even at
the maximum power. The superior sound quality can be compared with top-of-the-range AB-class analog systems, while the DA modules feature
a higher dynamics, very compact size and light weight and eciency above 90%. The DA module employed for powering the SW36XFA delivers in
an ultra-compact package a maximum power of 4000W and features PFC (Power Factor Correcon), a technology able to guarantee always the
highest level of power regardless of any eventual uctuaons of the power supply.
SIGNAL PROCESSING
The system processing is based on the CORE DSP plaorm, which has been designed by the PROEL R&D Laboratories using one of the most
advanced SHARC DSP for audio applicaon. It features 40bit, 96kHz oang point resoluon and high quality 24bit AD/DA converters, for a perfect
signal integrity, a dynamic range in excess of 110dB and a superior sonic performance. Thanks to its massive processing power, the CORE plaorm
is capable of providing the most sophiscated algorithms for speaker processing, together with remote control and networking capability.
The PRONET control soware, working on a solid and reliable CANBUS based network protocol, provides an intuive interface for the remote
control of the whole system, with the possibility of eqing, delaying, increasing the protecons and monitoring the status of the amplier.
PRONET
PRONET soware has been developed in collaboraon with sound engineers and sound designers, in order to oer an “easy-to-use” tool to setup
and manage your audio system. With PRONET you can visualize signal levels, monitor internal status and edit all the parameters of each connected
device.
Download the PRONET app from the AXIOM website at hp://www.axiomproaudio.com/ clicking on downloads secon of the product.
The AXIOM acve loudspeaker devices can be connected using the network connecon, in this case the PROEL USB2CAN converter oponal
accessory is needed. The rst me you connect a device with the USB2CAN converter, Windows O.S. will ask you to install the driver les, which
you can nd in the Driver folder within the Pronet applicaon folder (by default is C:\Program Files\Proel\Pronet\Driver, or if you changed it <your
path>\Driver). Please refer also to “Installaon” and “Drivers” paragraphs in the Pronet documentaon.
The PRONET NETWORK is based on a robust, reliable and fast communicaon protocol called CANBUS. The devices in a PRONET NETWORK are
connected together with a “linear bus topology”. The USB2CAN converter must be connected to the network input of the rst device, the network
output of the rst device is connected to the input of the second and so on. For the network connecons simple RJ45 cat.5 or cat.6 ethernet
cables can be used (please don’t confuse a ethernet network with a PRONET network these are completely dierent and must be fully separated
also both use the same kind of cable).
The beginning and the end of a PRONET NETWORK must be terminated. One side is terminated by the USB2CAN converter, the other side must
be terminated pressing the TERMINATE switch on the last device. All devices between these two points must have the TERMINATE switch lied.
Assign the ID number
To work properly in a PRONET network each connected device must have a unique idener number, called ID. By default the USB2CAN PC
controller has ID=0 and there can be only one PC controller. Every other device connected must have its own unique ID equal or greater than 1:
in the network cannot exist two devices with the same ID.
An ID number is assigned automacally to each devices when they are turned on for the rst me connected to a network.
In order to correctly assign a new available ID to each device for working properly in a Pronet network, follow these instrucons:
1. Switch o all the devices.
2. Connect them correctly to the network cables.
3. “TERMINATE” the latest device in the network connecon.
4. Switch on the rst device keep pressed “PRESET” buon on the control panel.
5. Leaving the previous device switched on, repeat the previous operaon on the next device, unl the latest device is turned on.
The “Assign ID” procedure for a device makes the internal network controller to perform two operaons: reset the current ID; search the rst free
ID in the network, starng from ID=1. If no other devices are connected (and powered on), the controller assume ID=1, that is the rst free ID,
otherwise it searches the next one le free.
These operaons ensure that every device has it’s own unique ID, if you need to add a new device to the network you simply repeat the operaon
of step 4. Every device maintains its ID also when it is turned-o, because the idener is stored in the internal memory and it is cleared only by
another “Assign ID” step, as explained above. This means that if your network is made always of the same devices the assigning ID procedure must
be executed only the rst me the system is turned on.
For more detailed instrucon about PRONET see the PRONET USER’S MANUAL included with the soware.

Useful tools to set up properly a vercal array system using the SW36XFA subwoofer
This is a list of tools that can be very useful to set properly a vercal array system with the SW36XFA acve subwoofers.
CABLE TESTER
It is a good pracce to check all cables before each installaon, because even one faulty cable can compromise heavily the
system performance.
INCLINOMETER WITH LEVER
This tool can be used to verify the vercal array angle. It can be used at the top or at the boom of the array In this
case you have to sum all splay angles, so the maximum precision is needed for aiming the vercal array, parcularly
for long throw applicaons.
LASER DISTANCE METER
This instrument can be useful to measure the height of the vercal array and to know the distance between FOH-Subs and FOH-Array
for seng the delay me.
SMAART or similar acousc measurement system
These are useful to measure delays, phase and response of the system.
do not
pressed
pressed
last device
network
network
AX2010A
USB2CAN
PC NOTEBOOK
USB 2.0 port
STATUS
CONVERTER
USB2CAN
CODE: S/N: RATINGS: RoHS COMPLIANT MADE IN ITALY
USB2CAN 00001 5V --- 200mA
EXAMPLE OF PRONET NETWORK WITH AX2010A AND SW36XFA

PRESET
The SW36XFA has three factory presets already stored inside the CORE DSP, these preset are ready to
use the sub in combinaon with AX2010A vercal array loudspeaker or any other professional audio
system:
STANDARD PRESET: the response starts at 45Hz and the cuto is at 100Hz with LR 24dB/oct., use this
preset for almost any applicaon at ground stack and it must be used with the SW36XFA set as own
(see FLOWN SET UP).
INFRASUB PRESET: the response starts at 36Hz and the cuto is at 60Hz with LR 24dB/oct., use this
preset when a very deep bass response is required, it must be used at ground stack only, alone or
in combinaon with some other boxes set as STANDARD, absolutely do not use it in combinaon of
CARDIOD preset. NOTE: INFRA and STANDARD PRESET must NOT be used together in close units.
CARDIOD PRESET: the response of this preset is the same of STANDARD preset but when combined together as described further the sub stack is
capable to cancel tha bass in the backwards, absolutely it must be used in combinaon of other two boxes and at ground stack.
PREDICTION: EASE Focus 2
To aim correctly a complete system we suggests to use always the Aiming Soware - EASE Focus 2:
The EASE Focus 2 Aiming Soware is a 3D Acousc Modelling Soware that serves for the conguraon and modelling of Line Arrays and
convenonal speakers close to reality. It only considers the direct eld, created by the complex addion of the sound contribuons of the individual
loudspeakers or array components.
The design of EASE Focus is targeted at the end user. It allows the easy and quick predicon of the array performance in a given venue. The
scienc base of EASE Focus stems from EASE, the professional electro- and room acousc simulaon soware developed by AFMG Technologies
GmbH. It is based on the EASE GLL loudspeaker data le required for its use: AXIOM_AX Series_v2_3.GLL, please note that the version must be
2.3 or more. The GLL le contains the data that denes the Line Array with regard to its possible conguraons as well as to its geometrical and
acouscal properes.
Download the EASE Focus 2 app from the AXIOM website at hp://www.axiomproaudio.com/ clicking on downloads secon of the product.
Use the menu opon Edit / Import System Denion File to import the le AXIOM_AX Series_v2_3.gll from the installaon Data folder, the
detailed instrucons to use the program are located in the menu opon Help / User’s Guide.
Note: Some windows system can require the .NET Framework 4 that can be download from microso website at hp://www.microso.com/en-
us/download/default.aspx.
WARNING! CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITION OF USE:
• This loudspeaker is designed exclusively for Professional audio applicaons. The product must be installed by qualied personal only.
• Proel strongly recommends that this loudspeaker cabinet be suspended taking into consideraon all current Naonal, Federal, State and Local
regulaons. Please contact the manufacturer for further informaon.
• Proel do not accept any liability for damage caused to third pares due to improper installaon, lack of maintenance, tampering or improper
use of this product, including disregard of acceptable and applicable safety standards.
• During assembly pay aenon to the possible risk of crushing. Wear suitable protecve clothing. Observe all instrucons given on the rigging
components and the loudspeaker cabinets. When chain hoists are in operaon ensure that there is nobody directly underneath or in the vicinity
of the load. Do not under any circumstances climb on the array.
AIMING and SUSPENDING INSTRUCTIONS (FLOWN SET UP)
Suspending the sub-woofers has dierent advantages and some inconvenient. One inconvenient is that it’s not possible to use the cardioid
conguraon, while another one is that as the sub-woofers don’t couple with the ground and indoor usage can have dierent behaviours
depending on ceiling and walls. The advantages are that the space underneath the stage can be free from subs, the coupling between sub and
sat is beer and, using a column of 4-6 sub boxes, the basses can be steered more deeply into the audience with a more uniform distribuon of
the low frequencies.
The SW36XFA subwoofers can be suspended alone or at the top
of a vercal array of AX2010A loudspeakers using the KPTSW36
y bar. The boxes are linked together in a column using a series of
couplers integrated in the frame of each enclosure. Each system can
be set properly both acouscally and mechanically, using the aiming
soware.
Coupling the system in the front does not require any adjustment:
using two locking pins, each loudspeaker box is xed to the previous.
The sloed bar in the back is inserted in a U-shaped frame that
features a series of numbered holes. Sliding the sloed bar in the U-
shaped frame of the next loudspeaker and inserng a locking pin in
one of the numbered holes, it is possible to adjust the relave splay
angle between two adjacent loudspeakers in the array column.
KPTSW36 y bar maximum capacity is 780 Kg (1719 lbs) with
the 0° angle. It can support, with a safety factor of 10:1, up
to:
• 16 AX2010A (ybar from 0 to 10°)
• 2 SW36XFA + 12 AX2010A (ybar from 0 to 10°)
• 6 SW36XFA + 4 AX2010A (ybar from 0 to 10°)
• 8 SW36XFA (ybar at 0°)
Follow the sequence in the gure for xing the y bar at the rst box.
Usually this is the rst step before liing up the system. Be careful to
SUSPEND HOLES
SUSPEND HOLE
INDICATOR
AX2010 REAR BOX
PIN ATTACHMENT
SW36XF REAR BOX
PIN ATTACHMENT
FRONT BOX
PIN ATTACHMENT
FRONT BOX
PIN ATTACHMENT
STRAIGHT SHACKLE 16mm
(not supplied)
M10 FOOT FOR
STACKED INSTALLATION
(OPTIONAL)
IDENTIFICATION AND
DATA LABEL
KPTSW36 FLY BAR AND ACCESSORIES
REST PIN FOR
UNUSED ATTACHMENT

insert properly all the locking pins (1)(2) and (3)(4) then the shackle (5) in the right holes as specied by the aiming soware.
When liing the system always proceed gradually step by step, paying aenon to secure the y bar to the box (and the box to the other boxes)
before pulling up the system: this makes easier to insert properly the
locking pins. Also when the system is released down, unlock gradually
the pins.
During the liing be very careful to not let the cables enter the space
between one enclosure and the other, as their compression could cut
them.
Please note that the boom Rear Link Bar of the SW36XFA cabinet is
retained in the guide with a magnet, force it to release it down, it is
free to slide from rear to front of the box (see gure): the backward
posion is to link another SW36XFA box, the forward posion is to link
a AX2010A box.
Wind loads
When planning an open-air event it is essenal to obtain current weather and wind informaon. When loudspeaker arrays are own in an open-air
environment, possible wind eects must be taken into account. Wind load produces addional dynamic forces acng on the rigging components
and the suspension, which may lead to a dangerous situaon. If according to the forecast wind forces higher than 5 b (29-38 Km/h) are possible,
the following acons have to be taken:
- The actual on-site wind speed has to be monitored permanently. Be aware that wind speed typically increases with height above ground.
- Suspension and securing points of the array should be designed to support double the stac load in order to withstand any addional dynamic
forces.
WARNING!
Flying loudspeakers overhead at wind forces higher than 6 b (39-49 Km/h) is not recommended.
If the wind force exceeds 7 b (50-61 Km/h) there is a risk of mechanical damage to the components which may lead to a dangerous situaon
for persons in the vicinity of the own array.
- Stop the event and make sure that no person remains in the vicinity of the array.
- Lower and secure the array.
1
2
3
4
1
2
5
KPTSW36 FLY BAR ASSEMBLY SEQUENCE
SW36XFA/P REAR LINK BAR
SW36 - SW36 link posion
SW36 - AX2010 link posion

1
3
2
24
4
5
KPTSW36 - SW36XFA - SW36XFA
ARRAY ASSEMBLING SEQUENCE
MAX:
KPTSW36
+
8x SW36XFA

1
3
3
2
2
4
KPTSW36 - SW36XFA - AX2010A ASSEMBLING SEQUENCE
MAX:
KPTSW36
+
2x SW36XFA
+
12x AX2010A

CARDIOID SET UP
The cardioid preset must be used in a sub array of three SW36XFA. Two box must be oriented towards the audience and one must be turned in
the opposite direcon (typically the box in the centre of the array). The boom and the top boxes must have the STANDARD PRESET, the box in
the middle must have the CARDIOID PRESET. The audio signal sent to all boxes is the same.
The CARDIOID PRESET has the same response of the STANDARD PRESET, but to obtain the maximum cancellaon on the back side of the array it
has the phase inverted and a proper level and delay seng.
The gure below shows two typical displacement of the array. The rst with all the boxes in vercal posion for a total height of 2400 mm and a
width of 750 mm. The second one with all the boxes in vercal posion for a total height of 800 mm and a width of 2240 mm.
use the AXFEETKIT (oponal)
on all the SW36XFA which permit
to slot in the boxes
80 cm min.
2.7  min.
120 cm min.
3.9  min.
80 cm min.
2.7  min.
stage
wall or other
big ostacle
bass sum direcon
bass cancellaon direcon
audience floor
NOTES:
When placing the cardioid array keep a distance to walls or other obstacles of at least 80 cm (2.6 ) in order not to aect the radiaon of the
reversed cabinet.
When placing mulple cardioid arrays keep a distance between them of at least 120 cm (3.9 ) in order not to maximize the combined radiaon
of whole arrays.

NOTES:
When placing the cardioid array keep a distance to walls or other obstacles of at least 80 cm (2.6 ) in order not to aect the radiaon of the
reversed cabinet.
When placing mulple cardioid arrays keep a distance between them of at least 80 cm (2.6 ) in order not to maximize the combined radiaon
of whole arrays.
LIMITED WARRANTY
Proel warrants all materials, workmanship and proper operaon of this product for a period of two years from the original date of purchase. If any defects are found
in the materials or workmanship or if the product fails to funcon properly during the applicable warranty period, the owner should inform about these defects the
dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed descripon. This warranty does not extend to damage resulng from
improper installaon, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and warranty is sll
valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defecveness.
• This unit package has been submied to ISTA 1A integrity tests. We suggest you control the unit condions immediately aer unpacking it.
• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspecon.
• Proel is not responsible for any damage that occurs during shipment.
• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
• Possible damages to unit should be immediately noed to forwarder. Each complaint for package tampered with should be done within eight days from product
receipt.
SAFETY INSTRUCTIONS
– To reduce the risk, close supervision is necessary when the product is used near children.
– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.
– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.
– This product should be located so that its locaon or posion does not interfere with its proper venlaon and heang dissipaon.
– Care should be taken so that objects and liquids do not go inside the product.
– The product should be connected to a power supply mains line only of the type described on the operang instrucons or as marked on the product. Connect the
apparatus to a power supply using only power cord included making always sure it is in good condions.
– WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
– Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connecon.
– Make sure that power supply mains line has a proper earth connecon.
– Power supply cord should be unplugged from the outlet during strong thunderstorm or when le unused for a long period of me.
CE CONFORMITY
Proel products comply with direcve 2004/108/EC (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with direcve 2006/95/CE (LVD), as stated in EN
60065 standard.
PROEL S.p.A. (World Headquarter) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY
Tel: [phone] Fax: [phone] www.axiomproaudio.comwww.axiomproaudio.com
stage
wall or other
big ostacle
bass sum direcon
bass cancellaon direcon
audience floor
80 cm min.
2.7  min.
80 cm min.
2.7  min.
80 cm min.
2.7  min.
use the AXFEETKIT (oponal)
on all the SW36XFA which permit
to slot in the boxes