Axiom KPTAX1012V User manual

Manufactured by PROEL
ITALY
FI-0161-01
SUPPLIED
MATERIALS:
1x KPTAX1012V
1x PLG714 14mm
straight shackle
LOAD LIMITS and WARNINGS
Up to four AX1012 cabinets are
allowed to be suspended from a single
KPTAX1012V y bar.
For stacked installaon on oor do not
exceed three cabinets for each KPTAX1012V y bar.
Use always the KPTAX1012V y bar with KPTAX1012
coupling bars to the sides of the array.
Never use KPTAX1012V for suspending an AX1012
horizontal array.
See AX1012 User’s Manual for complete rigging
instrucons and all the details about the use of
KPTAX1012V.
The MAXIMUM LOAD CAPACITY of KPTAX1012V is 595
kg (1311.7 lbs.) with balanced load.
SPARE PARTS:
94SPI8577O 8x63 mm
Locking Pin
OPTIONAL
ACCESSORY:
AXFEETKIT Kit of 6pcs
BOARDACF01 M10 foot
for stacked installaon
ASSEMBLING INSTRUCTIONS
Follow the sequence below to assemble up to four AX1012 units into a vercal array. The rst step before liing up the system is to assemble the
y bar to the rst box. Be careful to insert properly all the bars and their locking pins, with the shackle in the right hole as specied by the aiming
soware. When liing and releasing the system, always proceed slowly and gradually step by step, being careful to correctly assemble all the
rigging hardware and to avoid endangering yourself and your hands from being crushed
The KPTAX1012V y bar can be used also for down ring applicaons and for stacked installaons (oponal BOARDACF01 are needed).
1) Remove the pins at the end of the ying bar and insert the ying bar into the rails of the rst box.
2) Put back in place the pins in their hole, making sure that they are
inserted correctly. Fix the shackle in the chosen hole and link the
liing system.
3) Li the rst box, place the second box on the oor just
underneath the rst one. Let down slowly the rst box over
the second one, aligning the bumpers and the slots of the two
loudspeakers. Note: a proper wedge placed between the cabinet to
be linked and the oor can be useful.
KPTAX1012V
AX1012 VERTICAL ARRAY FLY BAR

4) Link the rst box to the second box using two coupling bars: remove the pins and the locking plates and insert the bars into the cabinet
rails from the front. Be sure that all hardware is rmly xed before liing the system and proceeding to link the third and fourth boxes.
STACKED SYSTEMS
For the stack conguraon you must use four oponal BOARDACF01 (C) feet and the y bar must be installed upside down to the ground.
The ground where the KPTAX1012V (A) ying bar serving as ground support is placed must be absolutely stable and compact.
Adjust the feet so to put the bar in a perfectly horizontal posion and always secure the system against movement and possible pping over.
A maximum of 3 x AX1012A cabinets are allowed for each KPTAX1012V and always be sure that all coupling bars KPTAX1012 (B) are rmly xed.
A
C
C
C
B
B
B
B
CONDITIONS OF USE
Proel do not accept any liability for damage caused to third pares due to improper installaon, use of non-original spare parts, lack
of maintenance, tampering or improper use of this product, including disregard of acceptable and applicable safety standards. Proel
strongly recommends that this loudspeaker cabinet be suspended taking into consideraon all current Naonal, Federal, State and
Local regulaons. The product must be installed be qualied personal. Please contact the manufacturer for further informaon.
PROEL S.p.A. (World Headquarters) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY
Tel: [phone] Fax: [phone] www.axiomproaudio.com
Manufactured by PROEL
ITALY
FI-0161-00
CUSTOMER ..................................................... BATCH NO. ......................................................
SERVICE SERVICE SERVICE SERVICE
KPTAX1012V
AX1012 VERTICAL ARRAY FLY BAR