AXIOMTEK MVS100-323-FL User manual

MVS100-323-FL
Mini Fanless Vision System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or rights of any
third party, or any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
©Copyright 2020 Axiomtek Co., Ltd.
All Rights Reserved
December 2020, Version A1
Printed in Taiwan

iii
ESD Precautions
The boards have integrated circuits sensitive to static electricity. To avoid damaging chipsets
from electrostatic discharge, observe the following precautions:
◼Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
◼Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help to discharge any static electricity on a
human body.
◼When handling boards and components, wear a grounding wrist strap available from
most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®is a trademark of Intel Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions ...........................................................................................iii
Section 1 Introduction....................................................................1
1.1 General Description ............................................................................1
1.2 System Specifications ........................................................................2
1.2.1 Main CPU Board ......................................................................................... 2
1.2.2 I/O System................................................................................................... 2
1.2.3 General Specification .................................................................................. 2
1.2.4 Vision I/O (12-pin terminal connetor) .......................................................... 3
1.2.5 LED Lighting control (4-pin terminal connetor) ........................................... 4
1.3 Dimensions..........................................................................................5
1.4 I/O Outlet ..............................................................................................6
1.5 Packing List .........................................................................................7
1.6 Switch Settings & Wafer connector...................................................8
1.6.1 AT/ATX Mode & Clear CMOS Optimal Defaults (SW1) .............................. 8
1.6.2 Wafer Connector for optional USB dongle (CN6) ....................................... 9
1.7 Connectors ..........................................................................................9
1.7.1 Mini Card Slot............................................................................................ 10
1.7.2 LAN ............................................................................................................11
1.7.3 USB ........................................................................................................... 12
1.7.4 VGA Connector........................................................................................ 12
1.7.5 DC-in Power Connector ............................................................................ 13
1.7.6 HDMI Connector........................................................................................ 13
1.7.7 ATX Power On/OFF Button & HDD LED Indicate..................................... 14
1.7.8 4-Pin Terminal Connector for LED Lighting Control .................................. 15
1.7.9 12-Pin Female I/O Connector ................................................................... 15
1.7.10 COM .......................................................................................................... 16
1.7.11 PD Power Indicator & GigE1 ~ GigE2 ports.............................................. 17
Section 2 Hardware Installation...................................................19
2.1 Installing the Memory Module..........................................................19
2.2 Installing the PCI Express Mini Card ...............................................20
2.3 Installing an internal USB dongle (Option) .....................................22
2.4 Installing Dail-rail mounting .............................................................23
2.5 Wall-mount bracket kit (Option) .......................................................24
Section 3 I/O Connection.............................................................27
3.1 I/O Connection (12-pin terminal connector)....................................27
3.1.1 Isolated Digital Input & Trigger Input ......................................................... 27

v
3.1.2 Isolated Digital Output & Trigger Output ................................................... 28
3.2 I/O Connection (4-pin terminal connector)......................................29
3.2.1 LED Lighting Control ................................................................................. 29
Section 4 Operating.....................................................................31
4.1 Operating ...........................................................................................31
4.1.1 Trigger Input/ Output ................................................................................. 31
4.1.2 LED Lighting Control ................................................................................. 32
4.1.3 Interrupt ..................................................................................................... 32
4.2 Application.........................................................................................33
4.2.1 Scenario .................................................................................................... 33
Section 5 AMI BIOS Utility ...........................................................35
5.1 Setting ................................................................................................35
5.2 Navigation Keys ................................................................................36
5.3 Main Menu..........................................................................................37
5.4 Advanced Menu.................................................................................38
5.5 Chipset ...............................................................................................50
5.6 Security Menu....................................................................................51
5.7 Boot Menu..........................................................................................52
5.8 Save & Exit Menu ..............................................................................53
Appendix A Watchdog Timer ................................................55
A.1 About Watchdog Timer .....................................................................55
A.2 How to Use Watchdog Timer............................................................55

vi
This page is intentionally left blank.

MVS100-323-FL User’s manual
Introduction 1
Section 1
Introduction
This section contains general information and detailed specifications of the MVS100 Series
Vision System, including the following sections:
⚫General Description
⚫Features
⚫Specifications
⚫Dimensions
1.1 General Description
The MVS100-323-FL is a mini fanless vision system that comes with an Intel® Atom®
x5-E3940 processor. It integrates dual camera interfaces and special vision I/O features for
machine vision applications, including GigE camera support, trigger input and output with
microsecond-scale real-time control, as well as LED lighting output with constant current
control to allow easy integration of any lighting source. To meet various usage needs, the
vision system can deliver high quality images for analysis when being used with inspection
software. The MVS100 can be deployed in factories to improve product quality and increase
productivity, and is suitable for the operations of fill level, label presence, OCR inspection, etc.
The system is compatible with any vision control system to simplify deployment of your
machine vision applications.
⚫Features
➢Integrated vision I/O
◼2 CH trigger input
◼2 CH trigger output
◼2 CH LED lighting control
◼4 CH isolated DIO
➢Supports camera interfaces
◼2 IEEE802.3af GbE LAN ports (PoE)
◼2 USB 3.2 Gen 1 ports
➢Power input: 24 VDC
➢-10°C to +55°C operating temperature range
➢Supports TPM 2.0 function

MVS100-323-FL User’s manual
2Introduction
1.2 System Specifications
1.2.1 Main CPU Board
⚫CPU
◼Intel® Atom® x5-E3940 processor (1.6GHz)
⚫Chipset
◼SoC integrated
⚫BIOS
◼AMI BIOS
⚫System memory
◼One DDR3L SO-DIMM, up to 8GB
1.2.2 I/O System
⚫Standard I/O interface
◼One power button (tactile switch with LED)
◼DC to DC power supply, supports 24VDC±10%
◼Two USB 3.2 Gen 1 type-A connectors
◼HDD access LED
◼One GbE LAN port (i211AT)
◼One VGA supports resolution up to 1920 x 1200 @60Hz
◼One HDMI 1.4b supports resolution up to 3840 x 2160 @30Hz
◼One RS-232/422/485
⚫Expansion interface
◼One full-size PCI Express Mini Card slot with mSATA signal for storage
⚫Camera interface
◼Two GbE LAN ports with PoE (Intel® i210-AT, IEEE802.3af compliant per port, total
max. power output 20W)
1.2.3 General Specification
⚫Operation temperature
◼-10°C to +55°C (+14°F to +131°F)
⚫Storage temperature
◼-20°C to +80°C (-4°F to +176°F)
⚫Humidity
◼10% ~ 90% (Non-condensing)
⚫Dimensions
◼53 mm (2.1") (W) x 155 mm (6.1") (H) x 110 mm (4.3") (D)

MVS100-323-FL User’s manual
Introduction 3
1.2.4 Vision I/O (12-pin terminal connetor)
⚫Isolated digital input
◼Number of channels: 2
◼Input type: wet contact: sink/source and dry contact
◼Input level for dry contact:
Close to ground (Logic 1), Open (Logic 0)
◼Input level for wet contact:
Input voltage: on (logic 1): 10~30VDC, off (logic 0): 0~3VDC
Isolation voltage: 2kV
◼Supports programmable de-bounce filter (disable, 100us, 500us, 1ms, 5ms)
⚫Isolated digital output
◼Number of channels: 2
◼Output type: sink, open collector
◼Supply voltage: 5-30VDC
◼Output current: Max. 100mA per channel
◼Isolation voltage: 2kV
⚫Isolated trigger input
◼Number of channels: 2
◼Input type: wet contact: sink/source and dry contact
◼Input level for dry contact:
Close to ground (Logic 1), Open (Logic 0)
◼Input level for wet contact:
Input voltage: on (logic 1): 10~30VDC, off (logic 0): 0~3VDC
◼Response time: <100us (from trigger input to trigger output)
◼Isolation voltage: 2kV
◼Supports programmable de-bounce filter (disable, 100us, 500us, 1ms, 5ms)
◼Trigger Input can be configured to DI by API
⚫Isolated trigger output
◼Number of channels: 2
◼Output voltage: 5-30VDC, sink, open collector
◼Output current: Max. 100mA per channel
◼Response time: <100us (from trigger input to trigger output)
◼Isolation voltage: 2kVDC
◼Trigger sources: 2CH trigger input (Each channel supports two sources.)
◼Trigger output can be configured to DO by API
⚫Interrupt
◼Sources: two digital inputs and two trigger inputs

MVS100-323-FL User’s manual
4Introduction
1.2.5 LED Lighting control (4-pin terminal connetor)
⚫LED lighting control
◼Number of channels: 2
◼Constant current control
◼Operating mode: strobe and continuous mode
◼LED output: 12/24VDC; Max. 0.5A per channel
Delay time & duration time: 1 μs to 65ms; 1ms to 65s (time unit: 1us, 16bit/ 1ms,
16bit)
◼Output current step size: 10mA by software
◼Trigger source: Each channel supports two sources (Trigger input 0/1)
Note: All specification and images are subject to change without notice.