Axor Citterio E 36704007 Manual

INSTALLATION
ZH ⁄ 用户手册 ⁄ 组装说明 02
EN ⁄ Instructions for use ⁄ assembly instructions 04
AXOR Citterio E
36704007

02
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
不得让儿童和肢体、精神和⁄或意识有障碍的成人
在不受监管的情况下使用淋浴系统。受酒精或毒
品影响的人员不得使用淋浴系统。
本产品只允许作为洗浴、卫生和洁身之用。
冷热水管间过大的压力差必须予以平衡。
安装提示
⁄ 安装前必须检查产品是否受到运输损害。 安装后
将不认可运输损害或表面损伤。
⁄ 管道和阀门必须根据通用标准进行安装、冲洗和
检查。
⁄ 请遵守当地国家现行的安装规定。
技术参数
工作压强： 最大 1 MPa
推荐工作压强： 0,1 - 0,5 MPa
测试压强： 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
热水温度： 最大 70°C
推荐热水温度： 65°C
热力消毒: 最大 70°C ⁄ 4 分钟
自动防止回流
该产品专为饮用水设计！
清洗(参见第页 16)
操作(参见第页 14)
安装(参见第页06)
保养(参见第页 12)
⁄ 此恒温龙头带有单向阀。 单向阀必须在
符合国家或当地的法律的情况下按照DIN
EN 1717定期检查（至少一年一次）。
⁄ 为了保证恒温器的稳定运转，请务必定期
从最热到最冷转动调温器。
校准(参见第页 10)
安装完成后必须检查调温器的出水温度。如
在取水处测量所得的温度与调温器上设定的
温度有偏差，那么必须进行调整。
安全功能(参见第页 10)
恒温阀芯的安全功能可以预先设定所希望的
最高出水温度，例如最高温度为42℃
大小(参见第页 15)
流量示意图
(参见第页 15)
时的流速
备用零件(参见第页 18)
请勿使用含有乙酸的硅胶！
符号说明
ZH

03 ZH
问题 原因 补救
⁄龙头出水量小 ⁄ 水压不足 ⁄ 检查总水压
⁄ 过滤网有垃圾堵塞 ⁄ 清洁龙头前面和恒温阀芯的过滤
网。
⁄ 花洒滤网有垃圾堵塞 ⁄ 清洗花洒和软管间的过滤网
⁄串水，在龙头关闭的状态下，热水
被强迫流入冷水管路，或者相反。 ⁄ 单向阀有垃圾堵塞或漏水 ⁄ 清洗单向阀，如有必要则更换新的
⁄龙头出水温度和温度设定的不符 ⁄ 恒温阀芯未被调节 ⁄ 调节恒温器
⁄ 热水温度过低 ⁄ 将热水温度从42ºC升高到65ºC
⁄水温无法调节 ⁄ 恒温阀芯表面结垢 ⁄ 更换-恒温阀芯
⁄安全停止按钮不工作 ⁄ 弹簧损坏 ⁄ 清洁弹簧和⁄或按钮，并视需要更换
⁄ 按钮僵化

04
SAFETY NOTES
Gloves should be worn during installation to prevent
crushing and cutting injuries.
Children as well as adults with physical, mental and ⁄or
sensoric impairments must not use this product without
proper supervision. Persons under the influence of alco-
hol or drugs are prohibited from using this product.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The hot and cold supplies must be of equal pressures.
INSTALLATION INSTRUCTIONS
⁄ Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and
tested as per the applicable standards.
⁄ The plumbing codes applicable in the respective coun-
tries must be observed.
TECHNICAL DATA
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C ⁄ 4 min
Safety against backflow
The product is exclusively designed for drinking water!
CLEANING (see page 16)
OPERATION (see page 14)
ASSEMBLY (see page 06)
MAINTENANCE (see page 12)
⁄ The mixer is equipped with check valves.
The check valves must be checked regularly
according to DIN EN 1717 in accordance
with national or regional regulations (at least
once a year).
⁄ To guarantee the smooth running of the ther-
mostat, it is necessary from time to time to turn
the thermostat from total hot to total cold.
ADJUSTMENT (see page 10)
After the installation, the output temperature of
the thermostat must be checked. A correction is
necessary if the temperature measured at the
output differs from the temperature set on the
thermostat.
SAFETY FUNCTION (see page 10)
The desired maximum temperature for example
max. 42º C can be pre-set thanks to the safety
function.
DIMENSIONS (see page 15)
FLOW DIAGRAM
(see page 15)
free flow
SPARE PARTS (see page 18)
Do not use silicone containing acetic acid!
SYMBOL DESCRIPTION
EN

05 EN
FAULT CAUSE REMEDY
⁄ Insufficient water ⁄ Supply pressure inadequate ⁄ Check water pressure (If a pump has
been installed check to see if the
pump is working).
⁄ Filters are dirty ⁄ Clean filter in front of the mixer and on
the MTC-thermo cartridge
⁄ Shower filter seal dirty ⁄ Clean filter seal between shower and
hose
⁄ Crossflow, hot water being forced into
cold water pipe, or vice versa, when
mixer is closed
⁄ Backflow preventers dirty or leaking ⁄ Clean backflow preventers, exchange
if necessary
⁄ Spout temperature does not corre-
spond with temperature set
⁄ Thermostat has not been adjusted ⁄ Adjust thermostat
⁄ Hot water temperature too low ⁄ Increase hot water temperature to
42 ºC to 65 ºC
⁄ Temperature regulation not possible ⁄ thermo cartridge calcified ⁄ Exchange thermo cartridge
⁄ Safety stop button not operating ⁄ Spring defective ⁄ Clean spring and ⁄or button, exchange
if necessary
⁄ Button calcified

06
1 mm
1 mm
2 3
36708187
SW 27 mm
SW 17 mm
1.
2.
1.
2.
1
Montage

07
1 - 2 mm
X
54
SW 24 mm
(15 Nm)
0,1 Nm
X + 11
76
98
Montage

08
1.
2.
SW 3 mm
(4 Nm)
11 12
1.
2.
SW 2 mm
(4 Nm)
1.
2.
2 3 4
1
2 3 4
1
1.
2.
2.
10 mm
10 mm
13 14
15 16
Montage

09
17 18
19 20
Montage

10
1 2
1
3
2
SW 2 mm
(4 Nm)
SW 2 mm
SW 2 mm
2.
2.
2.
2.
1.
1.
1.
1.
SW 3 mm
Justierung⁄Safety Function

11
43
65
7 8
2.
2.
2.
2.
1.
1.
1.
1.
SW 3 mm
(4 Nm)
SW 2 mm
(4 Nm)
Safety Function

12
2
34
1
6
5
SW 24 mm
SW 2 mm
SW 3 mm
1. 2.
3.
Wartung

13
8
910
7
11
SW 2 mm
(4 Nm)
SW 3 mm
(4 Nm)
SW 24 mm
(15 Nm)
1.
2.
3.
Wartung

14
开 ⁄ open
开 ⁄ open 关 ⁄ close
热 ⁄ hot 冷 ⁄ cold
关 ⁄ close
> 40°C
1.
2.
2.
2.
1. 1.
Bedienung

15
AXOR Citterio E
36704007
1812
bar
06 24 30 36 42 48 54 60
MPa
0 0,2 0,4 0,6 0,8 1,0
Q = l/min
Q = l/sec
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
120
120
120
120
380
12
Ø 38
Ø 38
Ø 49
6013013060
76
70 35
2
3 1
Maße ⁄ Durchflussdiagramm

16
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡水、指
甲油的残留也会对产品造成损伤。
此处：使用后要小心地用清水将剩余物冲洗干净。
同样在产品下方不得存放洗涤剂和化学药品，例如不
可放在用于洗脸盆的梳洗柜中否则挥发气体将损坏
产品。
在已经损伤的表面继续使用清洁剂会给表面造成更大
的损伤。
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥洗台、
浴盆和加热器采用的制造材料非常迥异，以适应产品
外形设计和使用功能的市场需求。
为了避免产品损坏和由此引发的投诉及争议，必须在
使用和清洁产品时遵循有关规程。
在保养汉斯格雅产品时，原则上必须注意：
⁄ 只能使用那些有明确注明是适用于本产品的清洁
剂。
⁄ 不允许使用含有盐酸、蚁酸、氯漂或醋酸的清洁
剂，因为这些清洁剂会给产品表面造成严重的损
伤。
⁄ 含磷酸的清洁剂必须在特定条件下使用。
⁄ 不允许将两种以上清洁剂混合使用。
⁄ 不允许使用具有研磨作用的清洁工具和设备，如不
适合的清洁粉末、海绵垫或超细麦克布。
⁄ 必须严格遵守清洁剂生产厂商的使用说明。
⁄ 严格遵守清洁剂的用量和作用时间，决不允许清洁
剂的作用时间长于规定值。
⁄ 定期的清洁以预防水垢。
⁄ 不允许将清洁剂直接喷射到汉斯格雅产品上，因为
喷雾会进入汉斯格雅产品的开口部分和缝隙中而造
成损害。首先将清洁剂喷在软布上，再用软布进
行清洁。
⁄ 清洁之后必须用足够的清水冲洗，以彻底去除残留
的吸附物（清洁剂）。
⁄ 不允许使用蒸汽清洗机，高温会损害产品。
表面损坏的部件必须更换，否则会有受伤的
危险。
不按规定进行清洁而造成的任何损坏不在本公司产品
保修范围之内。
担保
Hansgrohe 向用户保证，该产品无制造 缺陷。如
果自购买之日起五年内出现缺 陷，Hansgrohe 将
免费排除。 保证条件和详 情见 www.hansgrohe-int.
com⁄⁄⁄guarantee。 在提 出保修的权利时请联系您的合同
方。本保证 不涉及有关国家法律规定的消费权
Reinigung

17
IMPORTANT
Residues of toiletries such as liquid soaps, shampoos and
shower gels, hair dyes, perfumes, aftershave and nail
varnish can also cause damage.
Here too: Carefully rinse with water after use to remove
residues.
Likewise, do not store any cleaning agents or chemicals
under the products, for example in a vanity unit, as the
vapours may damage the products.
The damage of already damaged surfaces will deteriorate
under the effect of the cleansers.
COMPONENTS WITH DAMAGED SURFACES
MUST BE EXCHANGED, OTHERWISE THERE
COULD BE AN INJURY DANGER.
Damage caused by improper treatment will not be covered
by our guarantee.
WARRANTY
Hansgrohe guarantees to the consumer that this product
is free of production faults. If evertheless any defect is
detected within 5 years from date of purchase, Hansgrohe
will remedy this defect free of charge. You will find the
conditions and details of this guarantee at www.hansgrohe-
int.com⁄guarantee. Please contact your contracting party to
claim your rights under this guarantee. This guarantee does
not affect the customer‘s rights under the respective national
legislation.
CLEANING RECOMMENDATION FOR
HANSGROHE PRODUCTS
Today, modern sanitary and kitchen tapware, showers,
accessories, washstands, tubs and radiators consist of very
different materials to comply with the needs of the market
with regard to design and functionality.
To avoid damage and reclamations, it is necessary to
consider certain criteria when cleaning.
WITH REGARD TO CARING FOR
THE HANSGROHE PRODUCTS, THE
FOLLOWING MUST IN PRINCIPLE BE
HEEDED:
⁄ Only use cleaning material which is explicitly provided
for this type of application.
⁄ Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
⁄ Phosphorus acidic cleaners are only conditionally
applicable.
⁄ Mixing cleaning agents is not permitted, generally.
⁄ Never use cleaning materials or appliances with an
abrasive effect, such as unsuitable cleaning powders,
sponge pads or micro fibre cloths.
⁄ The instructions of the cleaning agent manufacturers
have to be followed absolutely.
⁄ Cleaning has to be carried out with a specified cleaner
dosage, contact time, object-related and adapted to
the needs.
⁄ The building up of calcifications has to be removed by
cleaning regulary.
⁄ When using spray cleaners, spray the cleaning solution
onto a soft cloth or sponge, never directly onto the
Hansgrohe products, as the atomised spray could enter
openings and gaps in the Hansgrohe products and
cause damage.
⁄ After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
⁄ The use of steam cleaners is not permitted. The high
temperatures can damage the products.

18
10790000
(25 mm)
AXOR Citterio E
36704007
98209000
(28x2,5)
98383000
(34x2)
98198000
(38x2,5)
96636000
95450000
92506000
98147000
(26x2)
95508000
(48x3)
95331000
97334000
92534000
98701000
97973000
97350000
96454000
98417000
(10 0x2, 5)
96633000
SW 24 mm
(M4x35)
SW 3 mm
97663000
(M4x16)
SW 2 mm
92541000
96393000
96393000
92515000
92514000
92343000
92441000
98433000
(30x1,5)
98433000
(30x1,5)
98128000
(13x2)
96370000
96370000
Serviceteile

19

AXOR ⁄ Hansgrohe SE
Auestraße 5–9
77761 Schiltach
Deutschland
[e-mail]
axor-design.com
07⁄ 2 017 9.06278.51