Axxera XDMA7200 Operating instructions

CD Rec
ei
ver
Made
for
~
iPod
D
iPhone
Installation &Owner's Manual
USB
Port
iPod
®/
iPhone
®/
Fiash Drive
0
Bluetooth
·
HFP
/A2DP/
AVRCP
CD
CD
-R/
RW
Compatib
le
SDHC
Supported
Au
x
3.
5mm
Input
MP3/WMA
Playback

XDMA7200
Preparation
Please read entire manual before installation.
Before You Start
• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing
the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit.
•
Insert the supplied keys into the
slots as shown, and slide the unit
out of
the mounting sleeve.
• Install mounting sleeve into
opening, bending
tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if
you are unsure.
• Certain vehicles may require an
installation kit
and/ or wiring
harness
adapter [sold separately). KEYS
• Test for correct operation and slide
into mounting sleeve
to secure.
• Snap
trim ring into place.
HEAD UNIT
MOUNTING KIT
OR DASH OPENING
MOUNTING SLEEVE
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
2

XDMA7200
Preamp
Connections
SUBWOOFER
------~
Steering Wheel Interface Input
PAC SWf.PS
connection
3.5mm
I
(aold
..
parately)
l
Bluetooth Microphone Input
Connect the included
Bluetooth microphone.
BLUE
I
Remote
Tur~n
Connect
to
amplifier
or
power
antenna. Insulate wire if
not
used.
BLACK
I
Ground
Connect
to
the vehicle
chassis ground.
RED
I
Accessory
Connect
to
an existing ignition
circuit
or
switched 12 volt source.
YELLOW I
Memory
0
Connect
to
the battery
circuit
or
constant 12 volt source
3
Wiring Diagram
Antenna Input
Connect the vehicle antenna
Bluetooth Microphone
(mustbe connected
for
Bluetooth functionality]
FUSE
When replacing the fuse,
make sure new fuse
is
the
correct
type and amperage.
Using
an
incorrect fuse could
damage the radio.
The
XDMA7200
uses one
10
amp
ATM
fuse located
beside the wiring connector.

XDMA7200
Receiver • Controls
Control Function Description
1
Mode
Changes
to
another
mode ofoperation.
2
Audio/Menu
Accesses
the
audio adjustmentoptions. Hold
to
access the setup menu.
3
Select/Power
Activates music searches. Confirms menu options. Hold
to
turn
the
power
off.
4
Mute
Mutes
the
audio output.
5
Bluetooth
Talk
Answers phone calls. Accesses
Number
Dial, Recent Calls and Redial functions.
6
Display Cycles displayed information. Hold
to
set
the
clock.
7
Front USB
Port
Connecta USB flash drive, iPod
or
iPhone device.
8
Open Opens
the
front
panel
to
access
the
reset
button,
CD
and
SO
card slots.
9
Auxiliary Input Connecta 3.
5mm
cable
from
the
headphone
output
of an
MP3
player.
10
Preset
6/ Folder Up
RecalljSet
preset
6. Changes
to
the nextfolder.
11
Preset
5/Folder
Down
RecalljSet
preset
5. Changes
to
the
previous folder.
12
Preset
4/ PiayjPause
RecalljSet
preset
4. Cycle between pausej
play.
13
Preset
3/lntro
Recall/Set
preset
3. Intra menu (plays
the
first
10
seconds of each song).
14
Preset
2/Random
RecalljSet
preset
2. Random menu (shuffles songs in a random playback order].
15
Preset
1
/Repeat
Recall/Set
preset
1.
Repeat menu (repeat
the
current
song, folder
or
album].
16
TrackjTune Up Changes
to
the
nextsong
or
radio station. Hold
to
fast
forward
or
seek
up.
17
Bluetooth
End
Call Ends
the
current
phone call. Hold
to
disconnect
from
Bluetooth.
18
Track/Tune Down Changes
to
the
previous song
or
radio station. Hold
to
rewind
or
seek down.
19
Back Steps backward
or
exits music searches
or
menus.
20
Band Accesses additional radio presets and cycles between FM and
AM
radi
o.
4

XDMA7200
OJ
Mode
0 Select/Power
0 Volume
Up
0 Audio/Menu
~
Tune
/Track
Up
0 Volume Down
[2_J
Mute
®
Preset
2/ Random
~
Preset
3/
lntro
(2.§)
Preset
6/ Folder
Up
~
Preset
5/ Folder Down
IR
Remote
·
Controls
5
(I§)
Key
9/ #
Key
(~)
End
Call
(~)
Key 0/ Display
@)
Talk
(2_§)
Key
7
I *
Key
G2J
Key
8/ Band
(2:§:)
Preset
4/
Piay
jPause
(~)
Preset
1/ Repeat
(~)
Back
(~)
Tune
/Track Down

XDMA7200
General Operation
Faceplate Removal
Power
On/Off
Source
Steering Wheel
Interface Input
Auxiliary Input
Volume
Mute
Reset
Display
Set the Clock
12/24-Hour Clock
Press RELEASE to fold down the front panel. While pushing
the front panel left, pull the right side away to remove. To
reinstall, slide in bottom left s1de, then snap left side up and
into place.
Press 0
or any other button to turn unit on. Press and hold
0 to turn unit off.
Press
MODE to select between AM/FM, CD, auxiliary input,
operation of iPod, USB,
SO and Bluetooth modes. Modes of
operation
are indicated in the display.
Note: CD mode will not appear unless a CD is inserted.
Operation of iPod mode will
not appear unless an iPod device
has been connected. USB and
SO modes will not appear
unless a USB device has been connected
or SO card has
been inserted.
The steering wheel
interface input located on the back
of
the head unit allows connection to the PAC (Pacific
Accessory Corporation)
SWI·PS interface module [sold
separately]. Visit www.pac-audio.com
for details.
To configure steering wheel controls, follow the instructions
provided with
the PAC SWI·PS interface module. After
Installing the interface module, insert the module's 3.5mm
jack into the port on the back of the head unit.
Insert 3.5 mm plug to connect your portable audio device.
Adjust volume using volume knob
[00-46).
Press MUTE to silence the audio.
Press
MUTE again to cancel.
Press
the RESET button, located behind the front panel,
to reset the unit back to the factory settings if abnormal
operation occurs.
Press DISP
to toggle between items such as clock, radio
frequency,
or 103 tag song information.
With the unit on, press and hold DISP until the clock begins
to flash, then release. Press TUNE .,.....,.... to adjust the
hours and TUNE ~~ to adjust the minutes. Press DISP
momentarily to save the selected time.
The clock will display 12-hour
AM/PM time in USA frequency
spacing mode rPM 1
o:oo). In European frequency spacing
mode,
the clock will display 24-hour time [22:00).
6

XDMA7200
Setup
Menu
Press and hold
AUDIO/MENU
for
more
than 3 seconds
to
access
the
setup menu, then press
AUDIO/MENU
to
cycle
through
menu options.
When
desired option appears
in
the
display,
rotate
the
volume knob
left/
right
to
adjust
or
activate desired function. Press
BACK
to
exit any menu
or
submenu.
Function
Options
Action
Auto
Station
Store
Tuner
Frequency
Spacing
AUTO
PGM
Press
SELECT
to
begin automatically
pro~lrc:nnlefttt:lg
STATIONS
to
the 6 buttons
in
the
FREQ
USA
Selectable iPod
t--------+--...;;;._-----------------_...,;,.---------1
Control
Loudness
Curve
Clock
Display
Auxiliary
Input
Beep
Confirmation
Power
on
Message
Scrolling
Option
Illumination
Dimmer
Note:
See page
22
for
Bluetooth setup menu options.
7

XDMA7200
Audio Menu
Press AUDIO/MENU momentarily to cycle between Bass, Treble, Balance, Fader,
Equalizer, Subwoofer, High Pass Filter and Source Volume
Level. Press BACK at any time
to exit the audio menu.
r BASS -+ TREBLE -+ BALANCE -+ FADER -+ EQ -+ SUBWOOFER -+ SOURCE LEVEL --,
Bass Press AUDIO/MENU until BASS appears, then rotate the
volume knob left/right to adjust (-6 minimum I +6 maximum].
Treble Press AUDIO/MENU until TREBLE appears, then rotate the
volume knob left/right to adjust (-6 minimum I +6 maximum].
Balance
Fader
EQ
Subwoofer
Source Volume Level
Note: Bass and Treble settings
are retained for each mode
individually.
Press
AUDIO/MENU until BALANCE appears, then rotate
the volume knob left/right to adjust (BALANCE LEFT 12 to
BALANCE RIGHT 12]. "BALANCE EVEN" represents equal
balance.
Press
AUDIO/MENU until FADER appears, then rotate the
volume knob left/right to adjust (FADER FRONT 12 to FADER
REAR 12]. "FADER EVEN'' represents equal fader.
Press
AUDIO/MENU until EQ appears. Rotate the volume
knob
left/ right to select between FLAT (default), POP, JAZZ,
CLASSIC, BEAT, ROCK and USER equalization curves. Press
SELECT to confirm. Any manual adjustment to the Bass,
Middle
or Treble settings are automatically saved as USER.
Press AUDIO/MENU until SUBWFR appears, then press
SELECT to confirm. Rotate the volume knob left/right to
adjust (0-12]. Adjusting the level to 0 turns the subwoofer off.
The source volume level control allows a gain adjustment
for each audio source. Set the source volume level for each
mode, depending
on the relative volume of each audio source.
To set the source volume level, press AUDIO/MENU until
"SOURCE LEVEL" appears. After one second, the current
mode will appear on the display. Turn the volume knob to
adjust the audio level of the current source (-6 minimum/ +6
maximum].
Note: Only the current mode will be available for adjustment.
Change
to another mode to set the source level for that
mode.
8

Stereo FM
Reception
XDMA7200
LCD
Icon Layout
Operation
Repeat Tuner of iPod USB Phone
Call
Loudness
CO-in
Artist
Name
--
FileName--
Song
Title--
Album
Name--
Folder Name
--
AM/FM
Tuner
Operation
Seek Tuning
Manual
Tuning
Band
Storing and Recalling
Station
Presets
Press
TUNE
............
or
TUNE
....,.....,.
for
more
than one second
to
seek
the
next
strong
station.
Press
TUNE
............
or
TUNE
....,.....,.
momentarily
to
move
radio frequency
up
or
down one
step
at
a time. Press and
hold
to
advance quickly.
Press
BAND
to
select between FM1, FM2, FM3, AM1 and
AM2
bands.
Up
to
six
presets
can be
programmed
for
each
band.
Up
to
18 FM stations and 12
AM
stations can
be
stored
in
memory.
To
store
a station, select
the
desired band and
station. Press and hold
the
desired
preset
button (1-6]
for
more
than two seconds.
When
stored, the
preset
number
will appear
in
the
display. The station can
be
recalled
by
pressing
the
corresponding
preset
button.
9

XDMA7200
CD Player Operation • Audio CDs
Insert
CD
Fold
down
front
panel
to
access the
CD
slot.
With
the
label
facing
up,
insert
a
standard
size
CD
into the
CD
slot. The
CD
will automatically begin playback.
Eject CD
Fold
down
front
panel and press EJECT
to
eject the
CD.
The
unit will change
to
previous mode of operation. If the disc
is
not
removed within
10
seconds,
the
unit will reload the disc.
The unit does
not
have
to
be
turned
on
to
eject
CD.
Track Select Press TRACK
..........
to
skip
to
the beginning of
the
next
track. Press TRACK
............
to
return
to
the beginning of the
current
track. Pressing TRACK
............
again skips
to
the
beginning of
the
previous track.
Fast
Forward/Reverse
Press and hold TRACK
..........
or
TRACK
............
to
fast
forward
or
reverse a track.
Pause Press
~/II
to
temporarily
stop
CD
playback.
Press
~/II
again
to
resume playback.
lntro
Press
INT
to
enter
the
Intra menu, then
turn
the volume
knob
to
select one of
the
following options:
•
OFF
-Cancels the
INT
function.
• ALL -Plays the
first
10
seconds of each track.
Repeat Press APT
to
enter
the
Repeat menu, then
turn
the
volume
knob
to
select one of
the
following options:
• ALL -Plays
all
tracks
on
CD.
• TRACK -Continuously repeats selected track.
Random Press
ADM
to
enter
the
Random menu, then
turn
the
volume knob
to
select one of
the
following options:
CD·R/CD·RW
Compatibility
•
OFF
-Cancels the
ADM
function.
• ALL -Plays
all
tracks
in
random order.
Some
CD-Rs
and CD-RWs may
be
incompatible with this
unit, depending on media type and recording method.
In
addition,
the
following
COs
may
be
incompatible with this
unit:
COs
exposed
to
extreme
temperatures
or
direct
sunlight
for
extended periods of time,
COs
recorded
in
which a recording
session failed
or
a re-recording was
attempted
and,
or
encrypted
or
copy-protected
COs
which
do
not
conform
to
the
audio
CO-DA
red book recording standard.
10

XDMA7200
CD Player Operation · MP3/WMA
Playing an MP3/WMA
Disc
Folder Access
When an MP3/WMAencoded disc is first inserted,
"READING" will appear
in the display. Depending on the
number of files and folders, this may take several seconds.
Press
&! to select the next folder.
Press
fi to select the previous folder.
*Folder access
is only available on discs recorded with more
than one folder.
Repeat Press APT to enter the Repeat menu, then turn the volume
knob
to select one of the following options:
• ALL -Plays
all tracks on CO.
• SONG -Continuously repeats selected track.
•
FOLDER -Continuously repeats all files in the folder.
Random Press ADM to enter the Random menu, then turn the
volume knob to select one of the following options:
•
OFF -Cancels the ADM function.
• ALL -Plays
all tracks in random order.
•
FOLDER -Plays all tracks in the folder in random order.
Note: Random mode is retained in memory when selecting
between
other modes and when the unit is turned on/ off.
Intra Press INT to enter the Intra menu, then turn the volume
knob
to select one of the following options:
•
OFF -Cancels the INT function.
• ALL -Plays
first 10 seconds of each track.
• FOLDER- Plays
first 10 seconds of each track in folder.
Note: Folder repeat, random and intra options only function
on MP3/WMA discs recorded with more than one folder.
Displaying Information Press DISP momentarily to select between artist/ song title
(default),
file/folder name, track number I clock & elapsed
time.
(LINE 1) ARTIST FILE NAME ELAPSED TIME TRACK NUMBER
(LINE 2) SONG TITLE--+ FOLDER NAME--+ CLOCK --+ TOTAL TRACKS
"NO ARTIST", ''NO TITLE
11
, or
11
NO ALBUM
11
will be displayed if
the file contains no 103 tag information.
"ROOT" will be displayed if the directory name of a root
folder is not labeled.
11

XDMA7200
CD Player Operation· MP3/WMA
File/Folder Search
Begin Searching Press SELECT to enter the file/folder search mode. A list of all the
folders from the CD will be displayed.
Note: Any files located
in the root directory will be located in the
folder named
11
ROOT
11
•
Choose a song Turn the volume knob to cycle through all the folders on the CD
and press SELECT to choose the desired folder. The list of files in
the selected folder will be displayed. Turn the volume knob to cycle
through the list of files.
Menu Navigation Pressing ESC when viewing the contents of a folder will return to
the list of folders on the CD. Press ESC again to exit the search
menu.
Playing a song Once
the desired song is displayed, press SELECT to begin playback
of
the desired song.
• •
Press
Folder 1 Folder 2
SELECT
I I
J J
Files Files
Press SELECT
to begin
• • •
Folder 3 Folder4 Folder 5
I I I
J J J
Files Files Files
Turn the
volume knob
12
• •
Folder 6 Folder 7
Press
I I
BACK
J J
Files
Files

XDMA7200
CD
Player Operation ·
MP3/WMA
File/Folder Compatibility and Support
Type Specification
•
CD-ROM
[ISO),
CD-R,
CD-RW
Compatible File Types •
CO-DA
[digital audio)
•
MP3
data [.mp3)
•
WMA
data [.wma)
• DAM protected files
•
WMA
lossless
• Apple lossless
Incompatible File •
WMA
Pro
Types •
MP3
Pro
•
MP3
playlists
•
WAV
lossless
•
M4A/
AAC
data
Recording
Format
•
IS09660
level
1 &
level
2
•
Yellow
book
MODE
1 &
MODE
2
FORM
1
Compatibility • Multi session
Sampling Frequency • MP3:
8kHz-
48kHz
Rate Compatibility • WMA: 32kHz -48kHz
Transfer
Bit
Rate
• MP3: 32kbps -320kbps
Compatibility • WMA: 32kbps -192kbps
•
Song
Title:
32
characters
•
Artist
Name:
32
characters
Character
Support • Album Name:
32
characters
•
File
Name:
32
characters
• Folder Name:
32
characters
103
Tag
Support
•
MP3
Tags:
Version
1.0-
2.4
•
WMA
Tags
• Maximum files:
999
File/Folder Limit • Maximum folders:
255
• Maximum folder
levels:
8
13

XDMA7200
Operation of iPodjiPhone
Connecting an iPodfiPhone Device
USB Connection
•
I
Using the
11
dock connector to USB
11
sync cable (provided
with
the iPodjiPhone device), plug the USB cable the
XDMA7200
1s USB port. Once connected, playback will begin
automatically.
Controlling a Device: Full Control
When the control of iPodjiPhone feature is set to "FULL" in the Setup Menu, use
the following functions to control the device:
Song Select Press
~~ to skip to the beginning of the next song.
Press
~~ to return to the beginning of the current song.
Pressing
~~ again skips to the beginning of the previous
song.
Fast Forward and Press and hold ~~ or ~~ to fast forward or reverse a
Reverse song.
Pause Press ~/II to temporarily stop playback.
Press
~/II again to resume playback.
Repeat Press APT to enter the Repeat menu, then turn the volume
knob
to select one of the following options:
• ALL -Repeats
all tracks.
•
SONG -Repeats selected track.
Random Press ADM to enter the Random menu, then turn the
volume knob to select one of the following options:
•
OFF -Cancels the ADM function.
• ALL -Plays
all tracks in random order.
• ALBUM -Plays
all tracks in the selected album in random
order.
Intra Press INT to enter the Intra menu, then turn the volume
knob
to select one of the following options:
•
OFF -Cancels the INT function.
•
ON -Plays first 10 seconds of each track.
14

XDMA7200
Operation of iPodjiPhone
Controlling a Device: Full Control • Music Search
The XDMA7200 features a powerful music search that simplifies the searching
process. Follow
the steps below to find the desired song:
Begin Searching Press SELECT to begin the search. The main search menu will
appear.
Select a
Category Turn the volume knob to select between playlist, artist, album,
song, podcast and audiobook. Press SELECT
to select the desired
search category. Some categories have subcategories
to navigate
through.
See the table below for details.
Search Category Menu Navigation
Playlist Menu
.. Playlists .. Songs
Artist
Menu .. Artists .. Albums .. Songs
Album Menu
.. Albums .. Songs
Song Menu
.. Songs
Audiobook Menu
.. Audiobooks
Pod
cast
Menu .. Podcasts
Step Backwards Press BACK to return to the previous menu, or exit the search
menu when the main menu
is shown.
Playing a Song Navigate
to the desired songjpodcastjaudiobook and press
SELECT
to begin playback.
I
1 Note: If a specific category
is selected, the iPod/iPhone device
playback will
be limited to that category until another category is
selected in the search menu.
Displayed Information
Displaying Information Press DISP momentarily to select file/folder name (default), song
title/ artist, track number 1clock & elapsed time.
(LINE 1)
(LINE 2)
SO
ANRGTTIS
1
TTLE _. ARTIST ELAPSED TIME TRACK NUMBER
ALBUM _. CLOCK _. TOTAL TRACKS
Character Support Maximum character display information
• *Song Title -
32 character maximum
•
*Artist Name - 32 character maximum
•
*Album Name - 32 character maximum
*Song Title,
Artist Name and Album Name will only be displayed if
included with
the file.
15

XDMA7200
Operation of iPodjiPhone
Controlling a Device: Manual Control
When the control of iPodjiPhone feature is set to "MANUAL" in the iPod Menu, use
the following functions to control the device:
Manual Control for iPod
Basic Head
Unit Control
Song Select
Pause
Volume
Compatibility
Made for
When "MANUAL'' control for iPod is selected from the Setup
Menu,
the iPod or iPhone device can be controlled directly
from the device's interface. All functions except for volume
can
be used from the iPod or iPhone device.
In addition to manual control of the iPodjiPhone device, the
following basic functions are still active:
Press
....,.....,. to skip to the beginning of the next song.
Press
.,.....,.... to return to the beginning of the current song.
Pressing
.,.....,.... again skips to the beginning of the previous
song.
Press
~/II to temporarily stop playback.
Press
~/II again to resume playback.
When playing an iPod device, the volume is adjustable using
the volume controls on inside panel.
To be compatible with manual control mode, the iPodjiPhone
device
must be update with the latest firmware using iTunes.
See the list below for compatibility details.
Device Compatibility
• iPod touch [4th generation]
• iPod nano
[6th generation]
• iPod touch
[3rd generation]
• iPod nano
[5th generation]
• iPod touch [2nd generation]
• iPod nano
[4th generation]
• iPod classic
• iPod touch
[1st generation]
• iPod nano 18rd generation]
• iPod nano 2nd generation]
• *iPod nano
[1st generation]
• *iPod with video
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
*These iPod devices are not compatible with manual control mode.
16

Connect a USB Device
(sold separately)
Connect an
SD Card
(sold separately)
Playing
Music
Track Select
Fast Forward and
Reverse
Pause
Folder Access
XDMA7200
USB/SD Card Operation
To play MP3/WMA files from most mass storage devices,
connect a device
to the XDMA7200's USB port.
To play MP3/WMA files from an SO Card, insert an SO card
into the
XDMA7200's SO card slot, located behind the front
panel. Insert the SO card with the label facing to the left, and
press the card until it clicks into place. Remove the
SO card by
pressing in until it clicks, then pull to remove.
When a USB or SO card device is first connected, playback
will begin momentarily. Depending
on the number of files and
folders,
it may take several seconds for the device to begin
playing.
If no valid MP3/WMA files are detected, "NO FILE" will
be displayed and the last mode will be resumed.
Press TRACK
....._....._ to skip to the beginning of the next track.
Press TRACK
.......... to return to the beginning of the current
track. Pressing TRACK .......... again skips to the beginning of
the previous track.
Press and hold TRACK ....._....._ or TRACK .......... to fast forward
or reverse a track.
Press .,./II
to temporarily stop USB playback.
Press .,./II again
to resume playback.
Press 6
to select the next folder.
Press 6
to select the previous folder.
Note: Folder access is only available on USB/SO Card devices
with
more than one folder.
Repeat Press APT to enter the Repeat menu, then turn the volume
knob
to select one of the following options:
• ALL -Plays
all tracks on the USB/SO Card device.
• TRACK -Continuously repeats selected track.
•
FOLDER -Continuously repeats all files in selected folder.
Random Press ADM to enter the Random menu, then turn the volume
Intra
knob to select one of the following options:
•
OFF -Cancels the ADM function.
• ALL -Plays
all tracks in random order.
•
FOLDER -Plays all tracks in folder in random order.
Note: Random mode is retained in memory when selecting
between
other modes and when the unit is turned on/ off.
Press
INT to enter the Intra menu, then turn the volume
knob
to select one of the following options:
•
OFF -Cancels the INT function.
• ALL -Plays
first 10 seconds of each track.
• FOLDER- Plays
first 10 seconds of each track in folder.
17

XDMA7200
USB/SD Card Operation
File/Folder Search
Begin Searching Press SELECT to enter the file/folder search mode. A list of all the
folders
from the USB device will be displayed.
Note: Any files located in the root directory will be located in the
folder named
11
ROOT
1•
Choose a song Turn the volume knob to cycle through all the folders on the device
and press SELECT
to choose the desired folder. The list of files in
the selected folder will be displayed. Turn the volume knob to cycle
through the list of files.
Menu Navigation Pressing ESC when viewing the contents of a folder will return to
the list of folders on the USB device. Press ESC again to exit the
search menu.
Playing a song Once the desired song is displayed, press SELECT to begin playback
of
the desired song.
Press
SELECT
• •
Folder 1 Folder 2
I I
J' J'
Files Files
Press SELECT
to begin
• • •
Folder 3 Folder4 Folder 5
I I I
J' J' J'
Files Files
Files
Turn the
volume knob
• •
Folder 6 Folder 7
I I
J' J'
Files Files
Displayed Information
Press
BACK
Press DISP momentarily to select between artist/song title (default), file/folder name
track number I clock & elapsed time.
(LINE 1)
(LINE 2)
ARTIST FILE NAME ELAPSED TIME TRACK NUMBER
SONG TITLE ---+ FOLDER NAME---+ CLOCK ---+ TOTAL TRACKS
18

XDMA7200
USB /
SD
Card Operation
File/Folder Compatibility and Support
Type
Specification
Compatible File Types
Incompatible File
Types
Sampling Frequency
Rate
Compatibility
Transfer
Bit
Rate
Compatibility
Ch
.
aracter
Support
103
Tag
Support
File/Folder Limit
USB/SO
File System
SO Card Capacity
•
MP3
data (.mp3)
•
WMA
data [.wma)
• DRM protected files
•
WMA
lossless
• Apple lossless
•
WMA
Pro
•
MP3
Pro
•
MP3
playlists
•
M4A/
AAC
data
•
WAV
lossless
• MP3: 8kHz -48kHz
•
WMA:
32kHz -48kHz
• MP3: 32kbps -320kbps
• WMA:
32kbps-
192kbps
• Song Title:
32
characters
•
Artist
Name:
32
characters
• Album Name:
32
characters
•
File
Name:
32
characters
• Folder Name:
32
characters
•
MP3
Tags:
Version
1.0-
2.4
•
WMA
Tags
• Maximum number of files: 500ID.O
..
• Maximum number of
folders:
.
~55(ptu§ithe
tyqp~folder)
• Maximum number of files
in
each
fo
.
lder:
;
50000
Note: For devices with more than
the
:
ma~imurn
qymber of
files/
folders,
some files will
be
ingnored
and.
may
not
funcggf)
pfigperly.
• FAT/FAT32 file system supported.
• HFS/NTFS/EXT2/EXT3 not supported.
16GB
or
less supported.
19

XDMA7200
Bluetooth® Operation
Pairing a Device
Preparation
Before
you
can use a Bluetooth device,
it
must
be
paired and
connected. Make sure
that
Bluetooth
is
activated
on
your
device before
you
begin
the
pairing process.
Pairing a
New
Device
The
XDMA7200
broadcasts the pairing signal constantly
when no devices are currently connected. Complete
the
pairing sequence
from
your Bluetooth device. Refer
to
the
owner's manual
for
your device
for
more
details.
Pairing Additional
Devices
The device name is "DUAL BT"
The Bluetooth passcode
"1234"
Note:
The
XDMA7200
can
be
in
any mode of operation
when pairing
is
performed.
If a device is currently connected, press and hold
~to
disconnect
the
current
device before a new device can
be
paired. Then begin
the
pairing sequence
from
the new
Bluetooth device.
Connecting a Paired Device
Most
Bluetooth devices support the auto-connect feature, and will connect automatically
if the device
is
in
range when the
XDMA7200
is
powered-on. If your device was previously
paired but does
not
connect, use these instructions below.
• If your
most
recently connected Bluetooth device becomes disconnected
or
does
not
reconnect, press
~
from
Bluetooth mode
to
reconnect your mobile device.
•
To
connect a previously paired device
that
was
not
recently connected:
1]
If
applicable, press and hold
~to
disconnect any connected mobile devices.
2]
From Bluetooth mode, press
SELECT.
"Paired Devices" will appear
on
the
LCD.
3]
Turn the volume knob
to
cycle through the list of devices.
4]
Press
SELECT
or~
to
connect
to
the desired device. It
must
be
in
range
to
connect.
Note:
If the
Auto Connect
setup menu setting
is
set
to
OFF,
you
must
press
"\to
connect
you
device
after
pairing, and each time the
XDMA7200
is
powered
on.
Disconnecting a Device
Press and hold
~
for
3 seconds
to
disconnect a connected device. The device will remain
paired and appear
in
the
PAIRED
DEVICES
menu, but
not
be
connected.
20