B.E.G. LUXOMAT AL5-RC-plus next User manual

EN
B.E.G.
LUXOMAT®AL5-RC-plus next
Mounting instructions - Floodlight AL5-RC-plus next 500
1. Function
The 500 W oodlight is supplied with a plug-in socket only
for the LUXOMAT®RC-plus next series. By means of this any
combination of 130°, 230° or 280° version can be achieved
with a minimum of stockkeeping.
You can get LUXOMAT® RC-plus next motion detectors with 3
different detection areas: 130°, 230° or 280°.
So you can attach the best motion detector to the oodlight to
cover every eld of application.
11
LUXOMAT®AL5-RC-plus next 500
4. Installation
Before installation the mains to be cut off.
The installation can only be done by an electrician.
Two holes for 6 mm pegs to be drilled in a distance of 50 mm.
The enclosed hexagon screws to be screwed in and now hang
on the oodlight.
(Do not forget the washers!)
Open the junction box by unfastening the 4 screws of the
cover. In order to get the right protection against wateringress
insert the cable through the cable inlet and connect the wires
accordingly to schematic. Fasten cover again.
Adjust oodlight for the right detection and illumination eld
and tighten the bracket hexagon screws.
(See also LUXOMAT® motion detector manual ).
5
Pluging-in
For plugging-in to produce
with the hand the right coun-
ter pressure.
Click Click
Unplugging
To remove the motion detec-
tor from the socket to use a
small screwdriver as shown
in picture.
5. Dimensions (mm)
145
184
130
175
160
102
3. The right mounting place
The oodlight must be mounted on a solid wall, protected
against rain, wind and sunradiation.
The recommended mounting height is 3 m. The distance
between oodlight and illuminated surface must be a minimum
of at least 1m. Also the distance to the street or to a neighbour-
ing house should be considered before xing the unit.
When the walking direction is lateral to the detection eld
of the motion detector, an optimum functioning of the motion
detector will be achieved. Moving frontally towards the motion
detector gives a much shorter range.
(See also LUXOMAT® RC-plus next motion detector manual)
3m
Power-supply: 230 V~ ±10%
Lamp: R7 s (118mm) max. 500 W
Protection: IP44 / I /
Housing: made of die-cast aluminium
Ambient temperature: -25° C to +50°C
Dimensions: H 160 x W 184 x D 290 mm
2. Technical data
145
184 130
175
160
115
ca. 30°
min. 1 m
Description Colour Part No.
AL5-RC-plus next white 92401
AL5-RC-plus next black 92400
Accessory
Fluo lamp 33316
CdS-T-AP 92367
RC-plus next 130 / 230 / 280
Lateral mounting to
walking direction Mounting hight

13
What should be done if ... Possible problems Solutions
1. The lamp being controlled
by LUXOMAT® does not
switch on.
- The halogen lamp is defective.
- The mains voltage is not present.
- The twilight value switch-on threshold is not
correctly adjusted.
- Incorrect adjustment of the detection zone
- The detector is installed too high.
- The lenses in the sensor section are dirty.
- Replace the halogen lamp.
- Check the connection and the fuses.
- Correct the switch-on threshold of the
twilight switch using the rotary control.
- Change the detection zone.
- Change the installation height (maximum 3 meters).
- Clean the sensor lenses.
2. The lamp turns on too late. - The detector is installed too high.
- People approach the sensor directly.
- Change the installation height (maximum 3 meters).
- Install the sensor in such a way that the detection zone is
intersected.
3. The lamps remain perma-
nently switched-on.
- Permanent movement of a heat source in
the detection zone
- A switch has been installed parallel to the
sensor in order to enable manual switching.
- Remove the heat source from the detection zone. Check
for correct functioning by covering the lens (the lamp must
then switch-off).
- Put the switch in the “Sensor” position in order to prevent
manual switch-on.
4. Unwanted switching-on
of the light
- Permanent movement of heat sources in the
detection zone (trees, bushes being moved
by the wind, the presence of cats or dogs
in the detection zone)
- Direct sunshine on the sensor lens
- The sensor is placed directly over an air
exhaust.
- Change the range of the sensor by changing the inclina-
tion or by attaching the shades to the lens.
- Protect the lens from direct sunshine.
- Install the sensor at a different location.
5. The detector range is too
small.
- The sensor installation height is not optimal
(too high or too low)
- People directly approach the detector.
- Hillside location
- Change the installation height (2.50 meters).
- Install the sensor in such a way that the detectionzone is
intersected.
- Change the detector inclination.
6. Does not detect vehicles - The vehicle engine is not yet warm
(weak heat source)
10. Mounting or replacement of the
halogen lamps
Always verify that the mains voltage has been isolated
whenever the halogen lamps need to be replaced.
Caution: The oodlight can reach very high temperatures!
• Allow the lamp and the enclosure to cool down.
• Remove the fastening screw from the enclosure of the
oodlight and open the enclosure.
• Grasp the defective halogen lamp tightly and remove it
from its bracket.
• Do not touch the replacement lamps with your hands.
• Place the halogen lamp into the bracket.
• Close the enclosure and be sure that the sealing ring is
properly seated.
• Close the enclosure with the fastening screws.
8. Troubleshooting
6. Wiring diagram
For surveillance of complete house
sites, warehouses, garages, loading
ramps etc.
For surveillance of two house-sites at
the same time, warehouses, garages
etc.
For surveillance of small properties,
drive-ins, row-houses etc.
7. Detection area at 2.50 m mounting hight
LUXOMAT®RC-plus next 130 LUXOMAT® RC-plus next 230 LUXOMAT® RC-plus next 280
L´ L N
PE
N
L
{}
Standard mode with 1-channel motion detector external
AL20-CdS
ALC-ELU/D
AL20-280-BM
AL20-280-BM-LED
ALC-B-360
ALC-B-360-DECO
AL2-RC-plus-130/230/280
FLC-280-LED
FL2-LED-230
AL5-RC-plus next
AL5-LC
AL1
AL4
Übersicht
L
N
L´LN
C1
E1
S1
Standard mode with 1-channel motion detector with NC pushbutton
Standard mode with 1-channel motion detector
T1 = NC button
Manual switching additionally possible (press opener ap-
prox. 2 sec.).
The position of the potentiometers should not be on “test”
or “sun”. If so, the pre-set time and safety values get lost.
AL20-280-BM
AL20-280-BM-LED
ALC-B-360
ALC-B-360-DECO
AL2-RC-plus-130/230/280
FLC-280-LED
FL2-LED-230
AL5-RC-plus next
AL5-LC
AL1
Übersicht
L
N
L´LN
C1
E1
T1
AL20-CdS
ALC-ELU/D
AL20-280-BM
AL20-280-BM-LED
ALC-B-360
ALC-B-360-DECO
AL2-RC-plus-130/230/280
FLC-280-LED
FL2-LED-230
AL5-RC-plus next
AL5-LC
AL1
max. 5 paralell
Übersicht
L
N
L´LN
C1
E1
L´LN
C1
11. Wiring diagrams
S1 = switch for permanent light
RC-plus next max. 5 parallel
20 m
20 m
6 m
130°
2,50 m
4 m
230°
20 m
20 m
6 m
2,50 m
4 m
280°
20 m
6 m
4 m
2,50 m
20 m
Motion detector Flood light
MAN 7313–AL5-RC-plus next-EN–050913-2