B-Tech AV Mounts BT8567-01 User manual

BT8567
UNIVERSAL
flat screen Display Trolley
with height ADJUSTMENT & flip rotation
INSTALLATION GUIDE
www.btechavmounts.com
B-TECH AV mounts
• Recommended for screens up to 70"
• Max load:
BT8567-01 20kg - 50kg (44lbs -110lbs)
BT8567-02 51kg - 70kg (111lbs -154lbs)
• Suitable for displays with VESA®xings
up to 600 x 400mm
• Tool-less height adjustment of screen
• Tool-less rotation of screen - change orientation of
screen from landscape to portrait (or vice-versa)
• Non-marking locking / braked castors included
• Dimensions: H.1905mm W.1075mm D.863mm
SPECIFICATIONS
BT8567-02BT8567-01
50kg

INSTALLATION SAFETY INSTRUCTIONS
CAUTION:
Do not attempt to install this product until all instructions and warnings have been read and properly understood.
Please keep these instructions for future reference.
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.
B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper
installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably qualied person install this product.
Warning: The trolley can tip over which may lead to serious injury. Only adults should push this trolley, do not allow
children under 16 to move the trolley. Push the trolley on the narrow side, never pull the trolley. Do not push at the top
of the trolley, push near the middle. Move the trolley slowly. Always park on level ground, never leave the trolley on an
incline. Apply the brakes when the trolley is stationary, release the brakes when pushing the trolley.
Great care must always be taken during installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install this product safely, then please consult a
professional for advice and/or to install this product for you. Failure to mount this product correctly may cause serious
injury or death both during installation and at any time thereafter.
Do not mount any AV equipment that exceeds the specic weight limit of the product you are installing.
This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Fixing hardware
It is highly recommended that all xing screws be used where supplied and that the purpose of all other xing hardware
is fully understood. In some cases more AV equipment xing hardware will be supplied to accommodate dierent models
of equipment and set up congurations.
The installer must be satised that any supplied xing hardware is suitable for each specic installation.
If any xing screws or included hardware are deemed not sucient for a safe installation then please consult a professional
or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features that the product might provide and ensure
that all cables are tidy and secure. Check to see that any moving aspect of the product can do so unhindered by any cabling.
Some products have moving parts and the potential to cause injury through the crushing or trapping of ngers or other
body parts.
Particular attention to the nature of moving parts is required especially when assembling installing and adjusting
during set up.
Immediately after installation double-check that the work done is safe and secure. Double-check all
necessary xings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its xing points are made as frequently as possible to
ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualied person.
2
CONTENTS
This mount is intended for use only with the
maximum weights indicated. Use with screens heavier than the maximum
indicated may result in instability causing possible injury.
Installation Safety Notes.......................................................................................................................
Parts List.....................................................................................................................................................
Installation Instructions........................................................................................................................
Product Dimensions.............................................................................................................................
B-Tech Contact Details........................................................................................................................
2
4
6
18
20
Please pay careful attention to where this product is located, some locations are not suitable for installation.
For indoor use only. Install stand on level ground. When verifying the stability of the structure, consider the following
external factors: The strength of the oor, exposure to sudden and severe wind and danger arising from contact with people
and / or objects (eg installations in passageways, emergency exits), if located in a public or frequently populated area ensure
that the product is out of the immediate reach of people.
Trolley Operation

CS
Společnost B-Tech AV Mounts doporučuje provést instalaci tohoto produktu instalátora AV či jinak způsobilé osoby.
Společnost B-Tech AV Mounts, její distributoři a prodejci nenesou prostřednictvím odborného odpov ědnost za škody nebo
zranění zp ůsobená nevhodnou instalací. Tento výrobek je nutno umístit do vhodné konstrukce a používat jen po uvedenou
maximální výšku.
DE
B-Tech AV Mounts empehlt, dass dieses Produkt durch einen qualizierten AV-Techniker oder eine andere Person mit
geeigneter Qualikation installiert wird. B-Tech AV Mounts, ihre Distributoren und Händler können nicht für durch fehlerhafte
Montage verursachte Beschädigung oder Verletzung haftbar bzw. verantwortlich gemacht werden. Dieses Produkt muss auf
eine geeignetem Untergrund montiert werden und darf nur bis zum angegebenen Höchstgewicht verwendet werden.
ES
B-Tech AV Mounts recomienda que un instalador de audio y video profesional u otra persona debidamente cualicada
instalen este producto. B-Tech AV Mounts, sus distribuidores y concesionarios no se hacen cargo ni se responsabilizan de
ningún daño o lesión provocados por una instalación inapropiada. Este producto se debe montar en una estructura adecuada
y se debe utilizar soportando solamente hasta el peso máximo indicado.
FR
B-Tech AV Mounts recommande de coner l’installation de ce produit à un installateur AV professionnel ou à une autre
personne dûment qualiée. B-Tech AV Mounts, ses distributeurs et ses revendeurs ne sauraient être tenus responsables de
tout dégât ou de toute blessure résultant d’une installation incorrecte. Ce produit doit être monté sur un support approprié et
utilisé dans la limite du poids maximum indiqué.
IT
JP
KR
B-Tech AV Mounts consiglia di adare l’installazione di questo prodotto a un installatore specializzato o ad altra persona
adeguatamente qualicata. B-Tech AV Mounts, i suoi distributori e rivenditori non accettano alcuna responsabilità nei riguardi
di eventuali danni o infortuni causati da un’errata installazione. Questo prodotto deve essere ssato a una struttura idonea e
utilizzato unicamente sino al peso massimo indicato.
NL
B-Tech AV Mounts adviseert om dit product te laten installeren door een professionele AV-installateur of andere hiervoor
gekwaliceerde persoon. B-Tech AV Mounts , haar distributeurs en dealers zijn niet aansprakelijk of verantwoordelijk voor
schade of letsel die is veroorzaakt door onoordeelkundige installatie. Dit product moet worden gemonteerd aan een
geschikte constructie, waarbij het aangegeven maximum gewicht niet mag worden overschreden.
PL
Firma B-Tech AV Mounts zaleca, aby ten produkt był instalowany przez profesjonalnych instalatorów AV lub inny
odpowiednio przeszkolony personel. Firma B-Tech AV Mounts, jej dystrybutorzy i dealerzy nie ponoszą odpowiedzialności
za uszkodzenia lub obrażenia ciała powstałe w wyniku nieprawidowej instalacji. Niniejszy produkt musi być amontowany
na odpowiedniej powierzchni, a podczas użytkowania nie wolno przekraczać podanego maksymalnego obciążenia.
PT
A B-Tech AV Mounts recomenda que a instalação deste produto seja efectuada por um instalador de AV instalador de AV
prossional ou outra pessoa devidamente habilitada. A B-Tech AV Mounts e os seus distribuidores e concessionários não
são responsáveis por danos ou lesões causados por uma instalação incorrecta. Este produto tem de ser montado numa estrutura
adequada e utilizado somente até ao peso máximo indicado.
RU
Компания B-Tech AV Mounts рекомендует, чтобы установка данного изделия производилась инженером по
установке аудtио-видеотехники или другим специалистом с соответствующей квалификацией. Компания
B-Tech AV Mounts ее дистрибьюторы и дилеры не несут ответственности за повреждения или травмы, полученные
в результате неправильной установки.
- AV
.-
.
.
B-Tech AV Mounts 는AV 설치 전문가 또는 적합한 지식을 갖춘 사람이 제품을 설치하도록 권장합니다. B-Tech AV Mounts
와판매점, 거래처는 이러한 안전 지침을 따르지 않을 경우에 수반될 제품의 손상이나 상해에 대한 책임을 지지 않습니다.
경우에 따라 제품이 설치되기에 적합하지 않은 곳들도 있으므로 설치 위치에 특별한 주의를 기울여 주시기 바랍니다.
제품의 설치 위치에 주의를 기울여 확인하십시오. 지정된 무게 제한을 초과하는 AV 장비를 장착하지 마십시오.
B-Tech AV Mounts は AV 設置の専門家または適合した知識を備えた人が製品を設置することを推奨します。 B-Tech AV Mounts
と販売店、取引先はこうした安全指針に従わない場合に随伴される製品の損傷や傷害に対する責任を負いません。場合によっ
て製品が設置されるに適していないところもあるので設置位置に特別な注意を傾けてください。この製品の位置に注意を傾け
て設置に適していない壁がいるかを確認してください。指定した重さ制限を超過するAV装備を装着しないでください。
CN
B-Tech AV Mounts ㆉ帽㦻ℶ❐䟀₢₩$9⸘孔ⅉ⛧㒥␅Ⅵ⚗㫋ⅉ⛧⸘孔ᇭ B-Tech AV Mounts ♙⸒䤓ⅲ䚕⟕ᇬ兞枏⟕ₜ⺈
䟀ℝₜ㋿㇢䤓⸘孔力抯㒟䤓㗮⯀㒥↳⹂微徲ᇭ㦻ℶ❐㉔權⸘孔⦷⚗抑䤓㩅㨓ₙ᧨ㄅ⅔䞷ℝₜ怔扖㓏㪖䯉䤓㦏⮶㔎摜ᇭ
3

BT8567 PARTS LIST
PLEASE KEEP THIS FOR FUTURE REFERENCE
4
2
3
1
12
13
14
10
11
6
5
47
8
9

5
INSTALLATION TOOLS REQUIRED
Crosshead
screwdriver
Pliers w/Cutter
(optional)
26
Drill with
10mm socket
Level
(optional)
15 16 17
18 19 20
21 22 23
24 25
REF PART NAME QTY
1 BASE 1
2
CASTOR 4
3
COLUMN 1
4
MOUNTING BAR 2
5
BALANCE BOX 1
6
BALANCE BOX COVER 1
7
ADAPTOR PLATES 2
8
MOUNTING PLATE 1
9
INTERFACE PLATE 1
10
COLUMN REAR COVER
2
11
COLUMN STRIP
2
12
COLUMN CAP
1
13
TRIM 2
14
VESA 600 ADAPTORS 2
15
5AF HEX KEY 1
16
M8 x 12mm CSK SCREW 4
17
M8 x 16mm CSK SCREW 3
18
M8 x 35mm CSK SCREW 3
19
M8 x 8mm SCREW 4
20
M8 x 10mm SCREW 8
21
M8 x 16mm SCREW 4
22
M8 x 20mm SCREW 2
23
M6 x 20mm CAP HEAD SCREW 2
24
PLASTIC WASHER 4
25
METAL WASHER 4
26
SLIDING NUT 8
INTERFACE KIT
A M4 x 12mm SCREW 4
B M4 x 25mm SCREW 4
C M4 x 40mm SCREW 4
D M6 x 16mm SCREW 4
E M6 x 25mm SCREW 4
F M6 x 40mm SCREW 4
G M8 x 16mm SCREW 4
H M8 x 25mm SCREW 4
I
M8 x 40mm SCREW 4
J 5mm SPACER 4
K 13mm SPACER 4
L
24mm SPACER 4
M M4 METAL WASHER 4
N M6 METAL WASHER 4
AB C
D
E
F
G
H
I
J
K
L
M
N

6
FIX CASTORS TO BASE
Screw 4 x item 2 into item 1 and apply the brakes.
1.
ATTACH COLUMN TO BASE
Stand item 1 in its upright position.
Insert item 3 into the cut out in item 1.
Screw 4 x item 17
through the underside of item 1 into item 3.
2.
INSTALLATION INSTRUCTIONS
1
2
3
1
17 26
3
17
1
17
M8 x 35mm

7
3.
i. Slide 8 x item 25 into the front slots of item 3.
ii. Attach item 4 to item 3 using 4 x item 19 fastening into item 25.
Mount one item 4 approx 10mm from the top of item 3 and
the other item 4, 433mm below.
ATTACH MOUNTING BARS TO COLUMN
3
25 4
19
26
4
21
26
21
Note: Item 21 does not need
to be fully tightened.
10mm
3
421 26
INSERT BALANCE BOX MOUNTING SCREWS
4.
Insert 2 x item 21 into the top item 4. Do not fully tighten, leave a 10mm gap (approx).
433mm
10mm
(approx)
4
4
25
3
21
M8 x 20mm
19
M8 x 10mm

8
5.
6.
5
5
SLOT
SLOT
Rear of item 6
INSERT BALANCE BOX REAR COVER
Insert item 5 into the slots on the left and right side of item 6.
5
6
6
6
TOP VIEW
21
6
KEYHOLE
6
5
4
HOOK ON BALANCE BOX
Hook item 6 onto item 21 using the keyhole xings on the rear of item 6.
4
5
21

9
Using a crosshead screwdriver and a spirit level, adjust the levelling screws on
the front of item 6 until the balance box is level.
7.
LEVEL BALANCE BOX
LEVEL
6
LEVELLING SCREW
25
6
Fix item 6 to the bottom item 4 using item 22.
4
6
Insert item 22 through these holes .
8.
FIX BALANCE BOX
22 22
22
M6 x 20mm

10
9.
6
7
7
16
25
16
FIX ADAPTOR PLATES
Attach 2 x item 7 to item 6 using item 16.
Use holes as shown below.
There are 3 height options for mounting item 8.
10.
FIX MOUNTING PLATE
Fix item 8 onto item 7 using items 18 & 24.
Option 2
Option 3
Option 1
7
8
24
18
26
Note: The maximum downward height adjustment
is 400mm
16
M8 x 16mm
18
M8 x 8mm