B-Tech BT8385-FTC User manual

www.btechavmounts.com
B-TECH AV mounts
BT8385-FTC
FLOOR-TO-CEILING MOUNTING KIT
Use with a bt8385 column
PARTS LIST
ITEM DESCRIPTION QTY
1 COLLAR 2
24
3
EXTENSION BAR
1
4
HEX KEY 1
END CAP
1
1
4
2
3

2
Installation Instructions
INSTALLATION SAFETY INSTRUCTIONS
B-Tech AV Mounts, it’s distributors and dealers are not responsible for damage or injury caused by improper installation,
improper use, modications, installations over the specied weight capacity and/or failure to observe these safety
instructions. In such cases, any warranty will expire.
It is recommended that this product should only be installed by a qualied professional / installer.
B-Tech AV Mounts does not claim any liability for any diculties that may arise from the interpretation contained
in these instructions. Failure to mount this product correctly may lead to serious injury and/or death.
Please check carefully to make sure there are no missing or defective parts - defective parts must never be used.
In the event of missing and/or defective parts, or technical questions, please contact an authorised dealer.
Pay careful attention to where this product is located, some locations are not suitable for installation. For indoor use only.
It is recommended that periodic inspections of the product are made as frequently as possible to ensure that safety is maintained.
Please keep these instructions for future reference.
CAUTION:
This product is intended for use only with the
maximum weights indicated. Use with equipment heavier than the
maximum indicated may result in instability causing possible injury.
1.
REAR SLOT
BT8385-190
BT8385-RTC
REAR SLOT
Ensure nuts slide into slots
1
1
4
50mm
50mm
TOP
INSERT COLLARS TO TOP OF COLUMN
Insert both items C1 into the rear slots of the column (Note: Ensure nuts slide into the slots).
Set item C1 50mm apart and from the top of the column.
1
1
2.
FIX END CAP TO COLUMN
Attach item 3 to the top of the column using the M6 x 12mm
screws supplied with the column (BT8385-190).
3
M6 x 12mm
SCREW
Note: Insert
Rail Mounting
Plate (BT8385-RTC)
to Column
(BT8385-190) before
attaching End Cap.
COLUMN
COLUMN
COLUMN
See back page on how to combine columns

3
3.
INSERT POLE INTO COLUMN
Insert the Ø50mm pole into the column
through items 1 & 3.
BT8385-190
BT8385-BDB
BT7850
BT7822
3
1
COLUMN
POLE
Pole inserted into column
Note: Keep loose, do not x.
CEILING
GRUB SCREWS
Extend pole
to
ceiling
1
POLE
CEILING MOUNT
1
GRUB SCREWS
FLOOR
4.
FIX TO STAND TO FLOOR & CEILING
Bolt the base to the ground and then extend the
pole and ceiling mount to the ceiling.
Secure pole in place using the grub screws on item 1,
then x ithe ceiling plate to the ceiling.
Note: Bolt stand to
the oor before xing
ceiling mount

www.btechavmounts.com
B-TECH AV mounts
AMA-BT8385-FTC-V1-0520-110 MADE IN VIETNAM
BT8385-FTC
FLOOR-TO-CEILING MOUNTING KIT
©2020 B-Tech International Design & Manufacturing Ltd. All rights reserved.
B-Tech AV Mounts is a division of B-Tech International Design & Manufacturing Ltd.
B-Tech AV Mounts, the B-Tech logo and Mode-AL are registered trade marks.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
CONTACT:
[email protected]
OPTIONAL EXTENDING THE COLUMNS
i. Fix 4 x item 2 into the top of a column, tighten the bottom 2 grub screws on each item 2.
ii. Slide another column on top, attaching to item 2 and tighten the remaining grub screws on item 2.
2
4
REAR
GRUB
SCREW
COMBINING COLUMNS
COLUMN
COLUMN
COLUMN
2
4
COLUMN