baby joy BC10126 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
EN DEFR ES IT PL
USER'S MANUAL/HANDBUCH
/MANUEL DE L'UTILISATEUR/MANUAL DEL USUARIO
/MANUALE UTENTE/INSTRUKCJA OBSŁUGI
BC10126
Baby Playard / Baby Reisebett / Lit Parapluie Bébé /
Cuna de Viaje / Lettino / Kojec 4w1 dla dziecka

Before You Start
General Warnings:
Attention: To prevent possible injury by entanglement, remove this toy when the
child starts trying to get up on its hands and knees in a crawling position.
Danger! Keep all small parts and packaging materials for this product away from
babies and children, otherwise they may pose a choking hazard.
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all Packaging, separate and count all parts and hardware before
installation.
Please ensure that all parts are correctly installed, incorrect installation can lead to
a danger.
We recommend that, where possible, all items are assembled near the area in
which they will be placed in use, to avoid moving the product unnecessarily once
assembled.
Ensure a secure surface during installation, and place the product always on a flat,
steady and stable surface.
Please read all instructions carefully and keep it for future reference.
- EN -
02

WARNING
WARNING
WARNING
SUFFOCATION HAZARD
Playard Warnings
INFANTS HAVE SUFFOCATED:
STRANGULATION HAZARD:
Failure to follow these warnings and the instructions could result in serious
injury or death.
This product including side rails, must be fully erected prior to use. Make
sure latches are secure.
• In gaps between a mattress too small or too thick and product sides
• On soft bedding
Never add a mattress, pillow, comforter, or padding.
Use only the mattress provided by manufacturer.
• The playard mattress/pad is specially designed to prevent suffocation. The
playard mattress/pad has a solid base, which must be at least 40”/102 cm
long and 28”/ 71 cm wide and not more than 1”/2.5 cm thick in order to
meet safety standards. Using a thicker or a different sized mattress/pad
may allow a child’s head to get between mattress/pad and the side of the
playard causing suffocation.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their back to sleep, unless otherwise advised by your physician.
• ALWAYS place child on back to sleep.
mattress covers not sold and intended for that purpose.
They can cause suffocation.
• NEVER use plastic shipping bags or other plastic film as
FALL HAZARD: Always check that the bassinet is securely locked on the
base/stand by pulling upwards on the bassinet.
NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN.
Infant may roll into space between pad and loose mesh side causing
suffocation.
• Strings can cause strangulation! NEVER place items with a string around a
child's neck such as hood strings or pacifier cords. NEVER suspend strings
over playard or attach strings to toys.
• NEVER use a water mattress with this product.
- EN -
03

WARNING
• NEVER place the playard near a window where cords from blinds
or drapes can strangle a child.
• Child can become entrapped and die when improvised netting or
covers are placed on top of a playard. Never add such items to
confine child in playard.
WARNING
IMPORTANT! To ensure safe operation of your playard, please follow these
instructions carefully. Please keep these instructions for future reference.
IMPORTANT! Before assembly and each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges. NEVER use if
any parts are missing or broken.
IMPORTANT! Adult assembly is required.
WARNING
See playard floor and side rails for warnings.
• The playard, including side rails, must be fully erected prior to use.
• Make sure latches are secure.
• Discontinue use of the product when child is able to climb out or has
reached the height of 35 in. (890 mm), or 33lbs. (15kg)
• When child is able to pull to standing position, remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
• ALWAYS provide the supervision necessary for the continued safety of your
child. When used for playing, never leave child unattended. Child in crib
must be under supervision at all times.
• ALWAYS ensure that the playard, changing table, and the Rock-A-Bye
Bassinet are safe by checking regularly, before placing the child in it, check
that every part is properly secured in place.
• NEVER leave the Bassinet in place when child is in playard. • NEVER leave
Changing Table in place when child is in the playard. • NEVER leave
Rock-A-Bye Bassinet in place when child is in the playard. Only one child can
use the Playard/Nursery Center at any time.
• NEVER use this product if there are any loose or missing fasteners, loose
joints, broken parts, or torn mesh/fabric. Check before assembly and
periodically during use.
• This product is not intended for commercial use.
- EN -
04

MAINTENANCE
MAINTENANCE AND CLEANING
INSTRUCTIONS:
Use only household mild soap and warm water.
DO NOT USE BLEACH.
DO NOT MACHINE WASH.
PARTS
Check the parts list on the back cover to make sure you have all the parts
for this model before assembling the playard.
Mattress Travel / Storage BagPlayard
(2) Short Bar with
Connectors
**Portable Rock-a-Bye bassinet
Large bassinet with
metal support tubes
(2) Curved
Connector Bar
*Music Center
Changing Table *Parent Organizer
- EN -
05

TO ASSEMBLE PLAYARD
ATTENTION: Playard must be fully
assembled and securely locked before
installing or using other accessories.
1) • Unzip bag and remove Playard frame (Fig.
1). Undo the Fasten straps and set the
Mattress aside.
DO NOT push center down yet.
2) • Top rails must be fully locked before lowering
center. Pull up one rail at a time, hold one hand on
each side of the rail and pull up sharply, do not pull
from the middle where the center latch release is
located, make sure both tubes latch in place and
each rail is rigid (Fig. 2).
IMPORTANT: The center must be raised while locking
the rails. If one rail will lock but the other side will
not then, unlock the rail by squeezing the release in
the center and try again.
Playard Mattress
Fig. 1
Fig. 2
Fig. 3a Fig. 3b
3) • Once all four (4) top rails are locked in place, push down on the center
handle (Fig. 3a).
The center mechanism automatically locks in place.
IMPORTANT: Test each top rail by pushing down slightly to confirm each is
rigid and securely in place before use (Fig. 3b).
ASSEMBLY
- EN -
06

To install mattress into the playard proceed
to Step 4.
4) • Place the Mattress on the floor of the Playard
with the padded side facing up (Fig. 4).
6) • To operate the brakes on the wheels, press
downward on the brake levers. To release, lift
upward on the lever (Fig. 6).
5) • Insert the hook & loop fasteners located on
the underside of the mattress through the
slots in the floor of each end of the playard
(Fig. 5a). Fasten the hook and loop fasteners
to the underside of the playard floor to prevent
the mattress from moving (Fig. 5b).
IMPORTANT: The handle located in the
center of the Playard floor MUST remain
raised (Approx. 45.7 cm or 18 inches) while
locking the side rails in place. If the center is
not raised the rails will NOT lock.
If you experience difficulty and one side of
the rail will lock but the other side will not
then, unlock the rail by squeezing the release
in the center and try again.
Fig. 4
Fig. 5a
Fig. 5b
Fig. 6
ASSEMBLY
- EN -
07

Latch release
Fig. 8a
Tube
Tube
TOP RAIL
Center latch
Fig. 9
Fig. 8b
Fig. 10
FOLDING PLAYARD
7) • Release the hook and loop fastener holding
the Mattress from underneath the Playard floor
or the Bassinet and set the mattress aside.
DO NOT unlock top rails yet, center of floor
handle must be raised before top rails will
unlock.
• Rotate the center handle counter-clockwise
90 degrees and raise the center as high as
the top rails (Fig. 7). Gather the Legs and
Wheels together towards the center as close
as possible so that they nearly touch.
8) • Locate the rail latch release in the center and bottom side of each rail.
Squeeze the lever with two hands until the rail releases the two tubes (Fig.
8a), then push down (Fig. 8b). NOTE: If the top rail(s) do not release
completely, DO NOT FORCE! Lift the center of floor higher. Both tubes must
be released for the top rail to fold.
9) • Gather all four (4) corners and
the center together tightly (Fig. 9).
Wrap Mattress around Playard frame
with padded side facing inward.
10) • Secure the hook and loop
fasteners by feeding them through
the loops on the end of the mattress
then fold them back onto themselves
(Fig. 10).
Place folded Playard into carry bag so
that the handle comes through the
opening between each side of the
zipper.
Rotate before lifting
Fig. 7
- EN -
08

WARNING
ACCESSORIES Bassinet & Cradles Warnings:
WARNING
Failure to follow these warnings and the instructions could result in serious
injury or death.
WARNING FALL HAZARD: To help prevent falls, do not use this product when
the infant begins to push up on hands and knees or has reached the height
of 25 in. (635 mm), weight of 22 lbs. (10 kg), whichever comes first.
• ALWAYS check that the large bassinet is securely locked on the base/stand
by pulling upwards on the large bassinet bed.
SUFFOCATION HAZARD Infants have suffocated:
• In gaps between extra padding and sides of bassinet/cradle and
• On soft bedding
Use only the pad provided by the manufacturer. NEVER add a pillow,
comforter, or another mattress for padding.
• Always attach large bassinet securely. If the large bassinet is not secured,
at all locations child could get neck trapped between large bassinet and
playard frame.
• Do not place items with a string around a child's neck strangulation! Do
not suspend strings over the large bassinet or attach strings to toys.
• NEVER mattress covers not sold and intended for that purpose. They can
cause suffocation.
• Use the large bassinet with only one child at a time.
• NEVER place a child under the large bassinet.
• The Playard must be fully assembled and installed before using.
• The playard, including side rails, must be fully erected prior to use. Make
sure each latch is secure.
• NEVER leave the large bassinet in place when child is in playard.
• NEVER place a child under the large bassinet.
• NEVER leave Changing Table in place when child is in the playard.
• NEVER leave the Rock-A-Bye Bassinet in place when child is in the playard.
Only one child can use the Playard at any time.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their back to sleep, unless otherwise advised by your physician.
• ALWAYS place child on back to sleep.
• ALWAYS provide the supervision necessary for the continued safety of your
child. NEVER leave children unattended.
• If a sheet is used with the mattress/pad, use only the one provided by
Babyjoy the dimension of the playard mattress.
- EN -
09

Fig. 11a Fig. 11b
Bassinet with metal support tubes
TO ASSEMBLE LARGE BASSINET
• Discontinue use of the large bassinet and the changing table when child
begins to push up on hands and knees or has reached the height of 25 in.
(635 mm), weight of 22 lbs. （10 kgs) or 3 months old, whichever comes
first.
• Child can become entrapped and die when improvised netting or covers
are placed on top of a playard. Never add such items to confine child in
playard.
SUFFOCATION HAZARD: Infant carrier
can roll over on soft surfaces and suffocate child. NEVER place carrier on
beds, sofas, or other soft surfaces.
FALL HAZARD: ALWAYS check that the largebassinet is securely locked on
the base/stand by pulling upwards on the large bassinet.
11) • Connect opposing Mattress Support Tubes that are attached to the
bottom of the Bassinet (Fig. 11a).
• Before placing the Mattress into the Bassinet, make sure Mattress Support
tubes are connected (Fig. 11b).
ATTENTION: Playard must be fully
assembled and securely locked
before installing or using the
Bassinet feature (See To Assemble
Playard section). You will need to
remove the mattress from the
bottom of the Playard to use
inside your Bassinet.
ASSEMBLY
- EN -
10

Fig. 12 Fig. 13
(2) Short Bar with Connectors (2) Curved Connector Bars (1) Changing Table
TO REMOVE LARGE BASSINET
TO ASSEMBL E CHANGING TABLE
ACCESSORIES
Changing Table:
12) • Position the Bassinet over and
down into the fully assembled
Playard. Secure in place by clip until
all are snapped into place (Fig. 12).
ATTENTION: Playard and large bassinet must be fully assembled and
securely locked before installing or using the changing table feature (See To
Assemble Playard and large bassinet section
Changing Table Assembly will require the following parts:
● Remove Mattress from Bassinet. Disconnect opposing Mattress Support
Tubes. Unsnap all clips and lift Bassinet.
Children may suffer serious injuries after falling from changing tables. Falls can
happen quickly.
● STAY within arm's reach.
ALWAYS secure the changing table to the playard frame.
SUFFOCATION HAZARD：
suffocate while sleeping on changing tables.
Changing tables are not designed for safe sleep.
● NEVER allow baby to sleep on changing table.
● NEVER leave the changing table in place when the child is in the large bassinet or
the playard. To prevent your child from falls and other injuries, always use the safety
belt when children are on the changing table.
● Discontinue use of the large bassinet and the changing table when child begins to
push up on hands and knees or has reached the height of 22 in. (558.8 mm), weight
of 22 lbs. (10 kg) or 3 months old, whichever comes first.
● Do not use changing table if it is damaged or broken.
● ALWAYS use the restraint system. Adjust belt as needed to get a snug fit.
13) • Place the Mattress into the
Bassinet with the padded side facing
upward (Fig. 13).
WARNING FALL HAZARD:
- EN -
11

Fig. 14a
Fig. 14b
Fig. 14c
Fig. 14d
Fig. 14e
Fig. 14f
14)● Lay the changing table cover on a flat
surface with the back side facing up. Locate
the 2 Curved Connector Bars (Fig. 14a).
Insert the Curved Connector Bars into the
backside of the Changing Table covering
(Fig. 14b).
● Attach the Short Bars with the 2 Connectors
to the Curved Connector Bars (Fig. 14c). .
Be sure the clips are faced up during this
preparation on the backside of the changing
table covering (Fig. 14d). Insert both
ends with the push pins into the Curved
Connector Bars. Ensure all pins click into
postion on all 4 connection points (Fig. 14e).
● Close the covering by using the hook and
loop fasteners on the flap. Flip the flaps over
the bars and fasten together (Fig.14f).
TO SECUR E THE CHA NGINGTABLE TO THE PL AYA RD
IMPORTANT!
When the changing table is on the upper position the changing table must be
secured to the playard frame by using the snap buttons straps or fasteners
provided.
- EN -
12

Fig. 15a
Fig. 16a
Fig. 16b
Fig. 15b Fig. 15c
TO USE CHANGING TABLE RESTRAINT SYSTEM
15) • Locate the 4 clip fasteners on the
bottom of
the changing table (Fig. 15a).
• To attach the changing table to the playard,
lower the changing table into the large
bassinet. Push down on the 4 clips to
secure it onto the large bassinet railing
(Fig. 15b). Secure the two snaps on the
strap down onto the Playard (Fig. 15c).
NOTE: DO NOT use changing table on
playard without the large bassinet and
securing the clips to playard.
16) • Place child on changing table, make sure hand and arms are clear of
the restraint.
Bring the restraint around the child’s waist and clip the male and female
ends of the buckle together (Fig. 16a).
• Tighten strap until fits snug around child’s waist (Fig. 16b).
DO NOT OVER TIGHTEN.
• To remove, unsnap the buckle.
ATTENTION: NEVER use changing table if it is damaged or broken.
- EN -
13

Parent Organizer
Fig. 18a
TO REMOVE CHANGING TABLE
17) • Unsnap from the playard (Fig. 17a). Locate all 4 clip/fasteners on the
changing table. Pull up on all 4 clips to release them from the playard frame
(Fig. 17b).
Warnings for Toy Accessories including Toybar / Mobile / Canopy with toys:
PARENT ORGANIZER ASSEMBLY
ACCESSORIES
18) • Parent Organizer
• Connect the Parent
Organizer to the Playard by
sliding the two connecting
clips over an open portion of
the top rail of the Playard
(Fig. 18a).
NOTE: The Parent Organizer
can only be installed on
open sides of the Playard
where the connecting clips
can easily be attached
without interfering with
other features.
Fig. 17a Fig. 17b
WARNING
- EN -
14

TO ASSEMBLE
PORTABLE ROCK-A-BYE BASSINET
WARNING
• Possible entanglement injury.
• Keep out of baby’s reach.
• Remove Toybar/Mobile/Canopy with toys when baby begins to push up on
hands and knees. Recommended use from birth to 5 months.
• Toys are not intended to be mouthed by the baby and should be
positioned clearly out of reach of the baby's face and mouth.
• ALWAYS attach all provided fasteners (strings, straps, clamps, etc.) tightly
to playard according to these instructions. Check frequently. • Do not add
additional strings or straps to attach to any other crib or playpen.
• The Toybar/Mobile/Canopy with toys is intended for visual stimulation and
not to be grasped by the child.
ASSEMBLY
- EN -
15

WARNING
WARNING
ACCESSORIES Bassinet & Cradles Warnings:
FALL HAZARD:
WARNING
Failure to fllow these warnings and the instructions could result in serious
injury or death.
FALL HAZARD: To prevent flls, stop using the product when infant:
● Begins to wiggle out of position or turn over in the product, head touches
the upper edge of the product, reached the height of 25 in. (635 mm),
weight of 22 Ibs.(10 kgs) (approximately 3 months of age).
● ALWAYS use restraint system if a restraint system is provided with the
product.
SUFFOCATION HAZARD
Infants have suffocated;
In gaps between extra padding and sides of bassinet/cradle and
● On soft bedding
Use only the pad provided by the manufacturer.
NEVER add a pillow, comforter, or another mattress for padding.
● When trapped between product and adjacent surfaces.
● ONLY use ROCK-A-BYE BASSINET on playard when it is securely attached.
● If a sheet is used with the pad, use only the one provided by Babyjoy or
one specifically designed to fit the dimension of the ROCK-A-BYE
BASSINET bassinet mattress.
● NEVER use ROCK-A-BYE BASSINET in different product.
Child’s activity can move carrier. NEVER place carrier on counter tops,
tables, or any other elevated surface.
NEVER use this carrier as a means to transport an infant in a motor vehicle.
Infant carriers not intended for use as infant restraint devices in motor
vehicles.
● To reduce the risk of SIDS, pediatricians recommend healthy infants be
placed on their back to sleep, unless otherwise advised by your physician.
● FALL HAZARD - Always check that the Rock-A-Bye is securely locked on
the
base/stand by pulling upwards on the Rock-A-Bye bed.
● The playard, including side rails, must be fully erected prior to use. MAKE
SURE EACH LATCH IS SECURE.
- EN -
16

● Stings can cause strangulation! NEVER place items with a string around a
child's neck such as hood strings or pacifier cords. NEVER suspend strings
over Rock-A-Bye bassinet or attach strings to toys.
● WARNING: Possible entanglement injury with toys attached. Keep out of
baby's reach.
● Do not use Rock-A- Bye bassinet or place on playard when baby begins to
push up on hands and knees.
● NEVER place product near a window where cords from blinds or drapes can
strangle a child.
● Always provide the supervision necessary for the continued safety of your
child.
NEVER leave child unattended.
● NEVER use plastic shipping bags or other plastic flm as mattress covers
not sold and intended for that purpose. They can cause suffocation.
● Use Rock-A-Bye bassinet with only one child at a time.
● DO NOT use large bassinet when using Portable Rock-A-Bye Bassinet.
NEVER place a child under the Rock-A-Bye bassinet.
● NEVER store the Rock-A-Bye bassinet in the playard while in use.
● The large bassinet must be fully assembled and installed before using.
● To help prevent heat build-up inside the playard and to avoid overheating
your child, when using the Rock-A-Bye Bassinet NEVER use an outdoor
canopy.
● NEVER leave Portable Rock-A-Bye Bassinet in place when child is in the
playard.
Only one child can use the Playard at any time.
● ALWAYS ensure that the playard, changing table, and Portable Rock-A-Bye
Bassinet are safe by checking regularly, before placing the child in it, that
every part is properly and securely in place.
● NEVER use this product if there are any loose or missing fasteners, loose
joints, broken parts, or torn mesh/fabric. Check before assembly and
periodically during use.
**Portable Rock-a-Bye bassinet
ASSEMBLY OF ROCK-A-BYE BASSINET
- EN -
17

CLICK
CLICK
CLICK
CLICK
Fig. 19a
Fig. 20a
Fig. 20b
X4 Fig. 20c
19) • Put the napper on a flat surface with the carry handle on the
underside.
Unfold each bar into its vertical position. Each bar should LOCK into
place automatically (Fig. 19a).
To fold napper bars: Push both buttons on each side of the bar while pushing
the bar downwards. Repeat for other bar (Fig. 20c).
20) • Extend each foot (x4) on both bars (Fig. 20a).
! ENSURE EACH BAR IS FIRMLY LOCKED INTO PLACE BY
PUSHING/PULLING ON IT.
Rotate the entire napper and stand it on the foot extensions(Fig. 20b).
ENSURE that napper is level and stable.
- EN -
18

• To lower handle, push both buttons
on each side of the handle with your
fingers while pushing the handle
backwards (Fig. 21c).
Fig. 21a
Fig. 21b
push push
Fig. 21c
ROCKER FUNCTION
Fig. 22a
Fig. 22b Fig. 22c
Manually Rock The Bassinet
21) • The rear of the canopy has 2 fabric
openings. Pull both opening over the 2
clips at the rear of the bassinet frame.
Ensure to wrap the elastic completely
over the bassinet frame (Fig. 21a).
NOTE: Always complete the canopy
before attaching the bassinet to the
playard frame.
22)● Turn the bassinet over and close the 4 peg legs
(Fig. 22a). Set Bassinet on a flat surface (Fig. 22b).
NOTE: Rocking requires adult assistance and
supervision, this is not an automatic rocking cradle
(Fig. 22c).
NEVER use Bassinet on raised surface such as Table,
Bed or Chair. A fall can OCCur.
● To raise the handle, push both
buttons on each side of the handle
with your fingers while pulling it
forward (Fig. 21b).
- EN -
19

23)● Locate the 4 clip fasteners on the bottom of the Rock-A-Bye Bassinet
(Fig. 23a).
● To attach the Rock-A-Bye Bassinet to the Playard, lower it into the large
bassinet.
Push down on the 4 clips and secure it onto the large bassinet ralling (Fig.
23b). Secure the two snaps on the strap down onto the Playard (Fig. 23c).
ATTENTION: Playard and large bassinet must be fully assembled and
securely locked before installing or using the Portable Rock-a-Bye bassinet
feature. (See To Assemble Playard and large bassinet sections. )
TO SECURE THE PORTABLE ROCK-A-BYE BASSINET
WARNING
CAUTION
Care must be taken when folding and unfolding to prevent finger
entrapment.
Do not alow children near while folding and unfolding.
TO FOLD REMOVABL EROCK-A-BYE BASSINET
WARNING
CAUTION
Care must be taken when folding and unfolding to prevent finger entrapment.
Do not alow children near while folding and unfolding.
Fig. 23b Fig. 23c Fig. 23a
- EN -
20