BaByliss for MEN POWERGLIDE TITANIUM 7448TU User manual

Model 7448TU

POWERGLIDE TITANIUM
The BaByliss for Men PowerGlide Titanium offers precision honed
titanium cutting blades and mains operation for continuous high power
to deliver an ultra smooth hair cut and lasting precision.
The 12 piece kit includes 6 cutting guides; 1, 2, 3, 4, 6 and 8 perfect
for creating a variety of different lengths and styles. A separate battery
operated trimmer is included, perfect for edging and shaping the
neckline and sideburns. A hard storage case completes the set, ideal
for storage and transport.
FEATURES
• Mains operated clipper
• Precision honed high grade titanium blades for lasting precision
• 5 position taper control for ne cut adjustment
• 6 comb guides: grades 1, 2, 3, 4, 6 & 8
• Separate battery operated trimmer for edging and shaping the
neckline and sideburns.
• Cleaning brush
• Oil
• Hard Storage case
• 3 year guarantee

SAFETY CAUTIONS
• This appliance should only be used as described within
this instruction book. Please retain for reference.
IMPORTANT CHILD SAFETY
WARNING! Polythene bags over the product or packaging
may be dangerous. To avoid danger of suffocation, keep
away from babies and children. These bags are not toys.
IMPORTANT SAFETY
• Do not immerse the appliance in water or other
liquids.
• Always inspect the appliance before use for
noticeable signs of damage. Do not use if damaged or if
the appliance has been dropped. In the event of damage
contact the Conair Customer Care Line (refer to ‘UK After
Sales Service’ section for further information).
• Only use the attachments supplied with this appliance.
• Do not leave the appliance unattended when switched on.
• Do not place the appliance on any surface whilst in
operation.
• Special care is required when using the appliance close to
the ears, eyes and face.
• This appliance should not be used by adults whose reduced
physical, sensory or mental capabilities, or whose lack of
experience and knowledge, might cause a hazard, unless
they have been correctly instructed to understand the safe
use and hazards involved and are adequately supervised.
• Careful adult supervision is required when this appliance

is used on or near children. Do not use on very young
children.
• This appliance should not be used, cleaned or maintained
by children. Keep out of reach of children.
• Always ensure that this appliance is kept out of the reach
of children at all times, particularly during use and whilst
cooling.
• Allow the appliance to cool before storing away.
• ThisappliancecomplieswiththerequirementsofDirectives
2004/108/EC (Electromagnetic Compatibility) and
2006/95/EC (Electrical Safety of Domestic Appliances).
• Always switch off and unplug the appliance when
changing the cutting guides, when cleaning or when not
in use.
• After use, do not coil the cord around the clipper as this
may cause damage. Instead, loosely coil the cord by the
side of the appliance.

MAINS OPERATED CLIPPER
INSTRUCTIONS FOR USE
Oiling Instructions
IMPORTANT! It is highly recommended before each use to oil the blades
with the oil provided. This ensures optimum cutting performance. For
the rst use you will need to use the oil supplied with the product,
unscrew the cap and cut off the very end of the plastic tube with a
pair of scissors to release the oil. To oil the blades ensure the unit is
switched on. Gently squeeze the oil tube and apply 2 drops of oil onto
the blades. Leave the unit on for a further few seconds to allow the oil
to thoroughly spread the length of the blades. Switch off the unit and
remove any excess oil by gently dabbing with a cloth.
Comb Guides
This appliance is supplied with 6 comb guides:
Cutting Length Grade
3mm #1
6mm #2
9.5mm #3
13mm #4
19mm #6
25mm #8
• To attach a comb guide, ensure the appliance is switched off. Slide
the cutting blades of the clipper under the slot in the rear of the teeth
of the comb guide and snap the clip on the bottom of the guide over
the bottom edge of the xed clipper blade.
• To remove the comb guide, ensure the appliance is switched off.
Push the tab on the rear of the comb guide away from the head and
lift off.

• Angle the clipper and gently stroke around the ear towards the back
of the neck.
• The 5-position lever enable ne cut adjustment for precision clipping.
• To increase the cutting length, push the lever down.
• To reduce the cutting length, push the lever up.
Preparation for Use
• Always inspect the appliance before use to ensure the clipper blades
are free from hair, debris etc.
• For best performance, use on clean, dry hair that has been combed
until tangle-free.
NOTE: The appliance should not be used for longer than 20 minutes
of continuous use.
Clipping
For an all over even cut:
• Attach a comb guide as required - your clipper is supplied with 6
comb guides (grades 1, 2, 3, 4, 6, 8). Each comb guide is labelled.
• Switch the clipper on and the blades will start to move.
• Starting at the nape of the neck, hold the clipper with the teeth of the
clipper pointing upwards, ensuring that the comb guide is resting at
against the head.
• Slowly move the clipper upwards and outwards through the hair
towards your crown, against the direction of the hair growth. The
comb guide will help to lift the hair while the blades cut the hair at the
desired length.
• Once the desired length is achieved at the back of the hair, start
clipping the top and sides.
• Hold the clipper to the front of your hair with the teeth pointing
towards the back of your head and move the clipper towards your
crown. Repeat if necessary, moving in rows from the front and the
sides of your head to the back.
• You should achieve an even length cut all over your head.

For a shorter back and sides, with length on the top:
• Attach the longer comb guide as required for the top of your hair -
your clipper is supplied with 6 comb guides (grades 1, 2, 3, 4, 6, 8).
Each comb guide is labelled with grade number and length.
• Switch the clipper on and the blades will start to move.
• Hold the clipper to the front of your hair with the teeth pointing
towards the back of your head and move the clipper towards your
crown. Repeat as necessary, moving in rows from the front and the
sides of your head to the back.
• If you wish to take the back and sides of your hair to a shorter length,
switch off the appliance and attach a shorter comb guide.
• Starting at the nape of the neck, with the comb guide at against
the head, move the clipper upwards and outwards over the area you
want to take shorter.
• Repeat on the sides of the hair, starting with the teeth of the clipper
pointing upwards and comb guide at against the area above the ear,
again moving the clipper upwards and outwards.
Outlining:
• To tidy up the edges around your cut e.g. neckline and sideburns,
detach the comb guides.
• Hold the appliance upside down, so the front of the clipper is facing
towards your head.
• Hold the clipper straight on your sideburns or neckline and move the
clipper downwards. This will give you a clean, smooth nish.

CLEANING & MAINTENANCE
For easy cleaning, the blades on your BaByliss For Men clipper are
removable. Regular cleaning will maintain their high performance level.
To clean proceed as follows:
• Switch the appliance off and unplug at the mains supply.
• Remove any comb guides. Rinse the comb guide under running
water and dry thoroughly before storage or use.
• Remove the blades carefully noting which way round they are tted.
This will help with re-assembling.
• Remove the two screws from the large xed blade and detach this
blade.
• Now brush away the hair and other debris from the interior of the
cutting head and blades.
• Re-assembly is simply the reverse of the above instructions.
• Finally, before fully tightening the two screws in the large blade, to
avoid injury ensure that the blades are correctly aligned. With the
taper control lever fully forward, the tips of the small blade must be
parallel with and 1mm below the tips of the large blade. Also check
that the extreme left hand tooth of the small blade is inside the large
blade. (Failure to do so could cause injury).
• Carefully tighten the two screws in the big blade, taking care not to
disturb the above correct position of the blades.
NOTE: Do not attempt to repair or replace the blades. In the event that
the blades become blunt or damaged, contact the Conair Customer
Care Line (refer to UK «After Sales Service» section for further
information).
INSTRUCTIONS FOR USE:
Preparation for Use
• Always inspect the appliance before use for noticeable signs of
damage. Do not use if damaged.
• Ensure the trimming heads are free from hair and debris (refer to
Cleaning and Maintenance section for further information).

Switching the Trimmer Heads
1. Ensure that the trimmer is turned off before switching the heads.
2. With the trimmer head in the locked position hold the handle of the
trimmer and turn the trimmer head anti-clockwise until the line on
the top section lines up with the beginning of the arrow. (Fig.1)
3. Lift the trimmer head from the handle.
4. To replace the trimmer head align the line on the top section with
the beginning of the arrow . Push the trimmer onto the handle. Turn
in a clockwise direction until the line is aligned with the spot on the
handle.
Note: make sure the motor spindle is in the actuator arm after
reassembling the head (Fig. 3)
Using the Trimmer
• Switch the trimmer ON.
• Move the trimmer upwards and outwards through the hair you wish to
remove. The wide trimmer is ideal for tidying sideburns and small
areas of facial hair.
• The wide trimmer head is ideal for shaping and styling the neckline
and sideburns or making small touch ups to any facial hair to add the
nishing touches, for a professional looking cut.
Note: never submerse unit handle into water.
Fig. 3
Motor spindle in actuator arm

CLEANING & MAINTENANCE:
To maintain optimum performance, the appliance should be cleaned after
each use.
• Ensure the appliance is switched ‘OFF’.
• Gently blow any hairs from the trimmer head.
• The attachment head can be removed and rinsed under the tap.
• Allow the trimmer to dry thoroughly before storing.
INSERTING BATTERIES
1. The battery compartment cover is located at the bottom of the
trimmer. To remove, twist the bottom section of the trimmer in an
anti-clockwise direction until the small mark located on the bottom
section lines up with the spot located on the upper section of the
trimmer Pull to remove (See g. 2).
Fig. 1
Fig. 2

2. Insert 1xAA alkaline battery, negative end rst, into the battery
compartment. (Alkaline batteries will ensure the best performance
and longest life for your appliance). If you are not going to use the
unit for a long period of time, or if the battery has run down, remove
the battery from the unit. This will increase the life of your trimmer.
3. To replace the battery compartment cover, line up the small mark
located on the bottom section of the trimmer with the spot and push
the bottom section onto the top section as far as it will go. Twist the
bottom section of the trimmer in a clockwise direction until it locks
into place, a soft click will be heard.
UK GUARANTEE
This BaByliss For Men appliance is guaranteed for consumer use for
3 years.
This guarantee covers defects under normal use from date of purchase
and ceases to be valid in the event of alteration or repair by unauthorised
persons. If the appliance does not perform satisfactorily due to defects
in materials or manufacture, it will be repaired or replaced through
Conair UK After Sales Service. The Conair Group Ltd reserves the right
to amend terms and specications without prior notice.
This guarantee in no way affects your statutory rights.
UK AFTER SALES SERVICE
For further advice on using the appliance or should you need to return
your product, please contact the Conair Customer Care Line on
03705 133191 (09:00 to 17:00 Monday to Friday) or email your enquiry
to [e-mail].
The return address is:

1: 150516
Customer Care Centre,
Conair Logistics
Unit 4
Revolution Park
Buckshaw Avenue
Buckshaw Village
Chorley
PR7 7DW
Please enclose your returns number, name and address details,
together with a copy of proof of purchase and details of the fault.
UK WIRING INSTRUCTIONS
The wires in the mains lead are coloured in accordance with the
following code:
• BLUE = NEUTRAL
• BROWN = LIVE
As the colours of the wire in the mains lead of this appliance may not
correspond with the colour marking identifying the terminals on your
plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N
The wire which is coloured BROWN must be connected to the terminal
which is marked with the letter L
Neither the BLUE nor BROWN wires should be connected to the
terminal which is marked with the letter E or the symbol
This appliance is supplied tted with a BS1363 mains plug and a
BS1362 3A fuse. If this plug is removed from the appliance please
ensure it is disposed of safely as a disconnected plug is dangerous if
reconnected to the mains. If any other type of plug is used, a 3A fuse
must be tted.