Badger Basket 02500 User manual

1.0/0811/TG
MODEL NUMBERS:
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-3:30 PM CST)
Web: http://www.badgerbasket.com/parts • E-mail: [email protected]
MAIL: PO Box 227, Edgar, WI 54426-0227 • Phone: [phone] • Fax: [phone]
MODERN CHANGING TABLE
WITH FOLDING HAMPER
& THREE FOLDING BASKETS
Assembly Instructions.
Adult Assembly
Required.
Save these instructions
for future use.
02500 - White
02502 - Espresso
02501 - Cherry
VERSION CODE:
1.0/0811/TG

1.0/0811/TG
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware.
If anything is missing or not satisfactory,
please DO NOT call the store or return
the product to them.
Please go online to:
http://www.badgerbasket.com/parts
Most problems are resolved
without you needing to leave home.
When emailing or calling us, please have this
instruction manual, your product model number,
and your Version Code ready.
Your Model Number is: See Cover Page
Your Version Code is: 1.0/0811/TG
USE AND CARE INSTRUCTIONS:
Wipe clean with a lightly dampened cloth as needed.
WARNING
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS AND SHARP
POINTS DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
WARNING - FAILURE TO FOLLOW THESE
WARNINGS AND THE INSTRUCTIONS COULD
RESULT IN SERIOUS INJURY OR DEATH
READ ALL INSTRUCTIONS before use of this changing table. Keep
instructions for future use. Choking Hazard! Keep unassembled parts out of the reach
of small children. Use only the parts, hardware, and changing pad provided by Badger
Basket. Do not use the changing table if it is damaged or broken. FALL HAZARD - To
prevent death or serious injury, always keep baby within arm’s reach. NEVER leave your
baby unattended, not even for a moment, when you are changing Baby’s diaper.
ALWAYS use the safety belt provided; and as an extra precaution keep at least one
hand on your baby at all times. DO NOT allow any children to climb or play on the table.
Periodically check to make sure all the bolts and screws remain tight. This table is
suitable for use with children weighing up to 30 lbs. (13.64 kg).

Ax1 Bx1
Cx2
Dx2
(DR&DF)
Ex2
(ER&EF)
Fx2
(FR&FF)
Gx2 Hx2 IBx1 Jx1
Kx1 Lx1 Mx1 Nx3
Ox20
Px20
LEFT SIDE PANEL RIGHT SIDE PANEL
SIDE COPINGS TOP RAILS -
Rear and Front
BOTTOM RAILS -
Rear and Front
VERTICAL POSTS BOTTOM SHELF
PANEL
SMALL SHELF
PANELS
SECOND RAILS -
Rear and Front
SAFETY BELT
METAL SUPPORT
BAR MATTRESS PAD
BASKET BODY &
BOTTOM PANELS
FOLDING HAMPER
& BOTTOM PANEL
6x58mm
6x12mm
Qx2
Rx4
6x45mm
4x20mm
TOOL REQUIRED
(NOT INCLUDED)
ALLEN WRENCH
SAVE THIS WRENCH
FOR FUTURE USE!
Sx12
PEGS
Ix1
TOP SHELF PANEL
T

DR
ERDF
EF
O
P
OP
O
P
O
P
Px4 Sx4
6x12mm
Ox4
6x58mm
ALLEN WRENCH
TOOL
2
S
S
S
S
AB
CC
RRRR
Rx4
6x45mm
ALLEN WRENCH
TOOL
1PLEASE REVIEW ALL
STEPS PRIOR TO
BEGINNING SO YOU
WILL BE FAMILIAR WITH
ALL PARTS AND THEIR
FINAL POSITIONS.

FF
G
O
P
FR
G
O
P
Px2 Sx2
6x12mm
Ox2
6x58mm
ALLEN WRENCH
TOOL
3
S
S
IB
IT
PO
PO
PO
P
O
P
O
O
P
Px6 Sx6
6x12mm
Ox6
6x58mm
ALLEN WRENCH
TOOL
4
DO NOT FULLY
TIGHTEN THE
BOLTS IN THIS
STEP SO THAT
YOU CAN
MORE EASILY
COMPLETE
THE NEXT
STEP.
S
S
S
S
S
S

H
H
O
P
O
P
O
PO
O
O
O
O
P
P
P
P
P
Px8
6x12mm
Ox8
6x58mm
ALLEN WRENCH
TOOL
5AFTER COMPLETING
THIS STEP, GO BACK
AND TIGHTEN ALL
OF THE BOLTS AND
BARREL NUTS YOU
ASSEMBLED IN
STEP 4.
K
L
Q
J
Q
Qx2
4x20mm
(NOT INCLUDED)
TOOL
6

M
7
x1
8
Nx3

BUCKLE CHILD SECURELY USING THE SAFETY BELT WHENEVER
CHILD IS ON THE TABLE. UNCLIP AND SEPARATE THE BUCKLE BY
SQUEEZING THE TABS ON THE SIDES TO RELEASE THE BUCKLE
TONGUE FROM THE BUCKLE. PLACE CHILD ONTO CHANGING
SURFACE AND SNAP THE BUCKLE AND BUCKLE TONGUE BACK
TOGETHER. KEEP CHILD'S SKIN/BODY CLEAR OF THE BUCKLE
WHEN SNAPPING AND UNSNAPPING TO PREVENT INJURY.
BUCKLE IS NOT SECURELY FASTENED UNLESS YOU HEAR AN
AUDIBLE "CLICK" TO INDICATE THE PARTS HAVE CONNECTED
SECURELY TOGETHER.
NEVER ALLOW CHILD TO STAND UP ON THE TABLE DUE TO RISK
OF FALLS AND INJURY OR DEATH. NEVER USE THE TABLE
WITHOUT THE SAFETY BELT AND METAL SUPPORT BAR IN PLACE.
ALWAYS SECURE THE CHANGING PAD TO THE CHANGING
SURFACE BY PLACING IT ONTO THE TOP SHELF AND ENSURING
THAT IT'S UNDERNEATH, NOT ON TOP OF, THE SAFETY BELT.
9