Baileigh Industrial B8075 User manual

OPERATOR’S MANUAL
ROTARY DRAW BENDER
MODEL: RDB-125 (B8075)

Table of Contents
STANDARD TERMS AND CONDITIONS OFSALE
INTRODUCTION............................................................................................................. 1
GENERAL NOTES.......................................................................................................... 1
SAFETY INSTRUCTIONS .............................................................................................. 2
SAFETY PRECAUTIONS ............................................................................................... 5
TECHNICAL SPECIFICATIONS..................................................................................... 7
UNPACKING AND CHECKING CONTENTS.................................................................. 8
Cleaning ...................................................................................................................... 8
TRANSPORTING AND LIFTING .................................................................................... 9
INSTALLATION............................................................................................................... 9
ASSEMBLY AND SET UP ............................................................................................ 10
GETTING TO KNOW YOUR MACHINE ....................................................................... 11
GENERAL DESIGN DESCRIPTION............................................................................. 12
ELECTRICAL ................................................................................................................ 13
OPERATION................................................................................................................. 15
Bending ..................................................................................................................... 15
Material Removal....................................................................................................... 16
DIE SELECTION AND INSTALLATION........................................................................ 17
Material Insertion ....................................................................................................... 20
Material Insertion Limitations..................................................................................... 21
Bending More than 180 Degrees............................................................................... 22
UNDERSTANDING SPRINGBACK .............................................................................. 22
MATERIAL SELECTION............................................................................................... 22
PIPE AND TUBE BENDING DIAGRAMS ..................................................................... 24
BENDING GLOSSARY ................................................................................................. 25
BENDING SUGGESTIONS .......................................................................................... 26
Aluminum Bending .................................................................................................... 26
Heavy Wall DOM tubing ............................................................................................ 26
Bending With Square Dies ........................................................................................ 27
Square Tooling Setup................................................................................................ 27
Large Size Square..................................................................................................... 28
LUBRICATION AND MAINTENANCE .......................................................................... 29
RDB-125 ELECTRICAL SCHEMATIC .......................................................................... 30
TABLES, CHARTS, & DIAGRAMS ............................................................................... 31
Diagram 1.................................................................................................................. 34
Diagram2 ................................................................................................................... 35
PARTS DIAGRAM ........................................................................................................ 36
Power Unit Assembly Parts Diagram......................................................................... 36
Stand Assembly Parts Diagram................................................................................. 37
Main Frame Assembly Parts Diagram ....................................................................... 38
© 2015 Baileigh Industrial, Inc.
Rev. 03/2015

Spring Back Lever Assembly Parts Diagram............................................................. 39
Ratchet Wheel Assembly Parts Diagram................................................................... 40
Swing Arm Assembly Parts Diagram......................................................................... 41
Spring Latch Assembly Parts Diagram...................................................................... 42
Cylinder Assembly Parts Diagram ............................................................................. 43
Parts List ................................................................................................................... 44

1
1
INTRODUCTION
The quality and reliability of the components assembled on a Baileigh Industrial machine
guarantee near perfect functioning, free from problems, even under the most demanding working
conditions. However if a situation arises, refer to the manual first. If a solution cannot be found,
contact the distributor where you purchased our product. Make sure you have the serial number
and production year of the machine (stamped on the nameplate). For replacement parts refer to
the assembly numbers on the parts list drawings.
Our technical staff will do their best to help you get your machine back in working order.
In this manual you will find: (when applicable)
•Safety procedures
•Correct installation guidelines
•Description of the functional parts of the machine
•Capacity charts
•Set-up and start-up instructions
•Machine operation
•Scheduled maintenance
•Parts lists
GENERAL NOTES
After receiving your equipment remove the protective container. Do a complete visual
inspection, and if damage is noted, photograph it for insurance claims and contact your
carrier at once, requesting inspection. Also contact your distributor and inform them of the
unexpected occurrence. Temporarily suspend installation.
Take necessary precautions while loading / unloading or moving the machine to avoid any
injuries.
Your machine is designed and manufactured to work smoothly and efficiently. Following proper
maintenance instructions will help ensure this. Try and use original spare parts, whenever
possible, and most importantly; DO NOT overload the machine or make any unauthorized
modifications.

2
2
Note: This symbol refers to useful information throughout the manual.
LEARN TO RECOGNIZE SAFETY INFORMATION
This is the safety alert symbol. When you see this symbol on
your machine or in this manual, BE ALERT TO THE
POTENTIAL FOR PERSONAL INJURY!
Follow recommended precautions and safe operating
practices.
UNDERSTAND SIGNAL WORDS
A signal word – DANGER, WARNING, or CAUTION
is used with the safety alert symbol. DANGER
identifies a hazard or unsafe practice that will result in
severe Injury or Death.
Safety signs with signal word DANGER or WARNING are
typically near specific hazards.
IMPORTANT
PLEASE READ THIS OPERATORS MANUAL CAREFULLY
It contains important safety information, instructions, and necessary operating
procedures. The continual observance of these procedures will help increase your
production and extend the life of the equipment.
SAFETY INSTRUCTIONS

3
3
General precautions are listed on CAUTION safety signs. CAUTION also calls attention to
safety messages in this manual.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
PROTECT EYES
Wear safety glasses or suitable eye protection
when working on or around machinery.
PROTECT AGAINST NOISE
Prolonged exposure to loud noise can cause impairment or loss of
hearing. Wear suitable hearing protective devices such as ear muffs or
earplugs to protect against objectionable or uncomfortable loud noises.
BEWARE OF CRUSH HAZARD
NEVER place your hands, fingers, or any
part of your body in the die area of this
machine. Be aware of the area on either side
of the dies for crush points created by
material movement.

4
4
BEWARE OF PINCH POINTS
Keep hands and fingers away from the drive
mechanisms, cylinders, ratchets, and other
moving linkage while the machine is in
operation.
KEEP CLEAR OF MOVING OBJECTS
Always be aware of the position of the material and the swing area in
which the material will travel. The material will swing with significant
force. This swing area will create pinch points and the force of the
material movement may cause serious bodily injuries.
HYDRAULIC HOSE FAILURE
Exercise CAUTION around hydraulic hoses in case of a hose or
fitting failure.
HIGH VOLTAGE
USE CAUTION IN HIGH VOLTAGE AREAS. DO NOT assume the
power to be off.
FOLLOW PROPER LOCKOUT PROCEDURES.

5
5
SAFETY PRECAUTIONS
Metal working can be dangerous if safe and proper operating procedures are not followed. As
with all machinery, there are certain hazards involved with the operation of the product. Using
the machine with respect and caution will considerably lessen the possibility of personal injury.
However, if normal safety precautions are overlooked or ignored, personal injury to the operator
may result.
Safety equipment such as guards, hold-downs, safety glasses, dust masks and hearing
protection can reduce your potential for injury. But even the best guard won’t make up for poor
judgment, carelessness or inattention. Always use common sense and exercise caution in
the workshop. If a procedure feels dangerous, don’t try it.
REMEMBER: Your personal safety is your responsibility.
1. Only trained and qualified personnel can operate this machine.
2. Make sure guards are in place and in proper working order before operating
machinery.
3. Remove any adjusting tools. Before operating the machine, make sure any adjusting tools
have been removed.
4. Keep work area clean. Cluttered areas invite injuries.
5. Overloading machine. By overloading the machine you may cause injury from flying parts.
DO NOT exceed the specified machine capacities.
6. Dressing material edges. Always chamfer and deburr all sharp edges.
7. Do not force tool. Your machine will do a better and safer job if used as intended. DO NOT
use inappropriate attachments in an attempt to exceed the machines rated capacity.
8. Use the right tool for the job. DO NOT attempt to force a small tool or attachment to do the
work of a large industrial tool. DO NOT use a tool for a purpose for which it was not
intended.
9. Dress appropriate. DO NOT wear loose fitting clothing or jewelry as they can be caught in
moving machine parts. Protective clothing and steel toe shoes are recommended when
using machinery. Wear a restrictive hair covering to contain long hair.
10.Use eye and ear protection. Always wear ISO approved impact safety goggles. Wear a full-
face shield if you are producing metal filings.
WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN
SERIOUS PERSONAL INJURY

6
6
11.Do not overreach. Maintain proper footing and balance at all times. DO NOT reach over or
across a running machine.
12.Stay alert. Watch what you are doing and use common sense. DO NOT operate any tool or
machine when you are tired.
13.Check for damaged parts. Before using any tool or machine, carefully check any part that
appears damaged. Check for alignment and binding of moving parts that may affect proper
machine operation.
14.Observe work area conditions. DO NOT use machines or power tools in damp or wet
locations. Do not expose to rain. Keep work area well lighted. DO NOT use electrically
powered tools in the presence of flammable gases or liquids.
15.Keep children away. Children must never be allowed in the work area. DO NOT let them
handle machines, tools, or extension cords.
16.Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust.
Always lock up tools and keep them out of reach of children.
17.DO NOT operate machine if under the influence of alcohol or drugs. Read warning
labels on prescriptions. If there is any doubt, DO NOT operate the machine.
18.DO NOT touch live electrical components or parts.
19.Turn off power before checking, cleaning, or replacing any parts.
20.Be sure all equipment is properly installed and grounded according to national, state, and
local codes.
21.DO NOT bypass or defeat any safety interlock systems.
22.Keep visitors a safe distance from the work area.

7
7
TECHNICAL SPECIFICATIONS
Maximum Center Line Radius (CLR)*
10.5" (266mm)
Minimum Center Line Radius (CLR)*
.5" (12.7mm)
Minimum OD
.25" (6.35mm)
Mild Steel Pipe (Schedule 40) Based on a
material tensile strength of 60000 PSI – mild
steel
2" (50.8mm)
Aluminum Pipe (Schedule 40)
2" (50.8mm)
Stainless Steel Pipe (Schedule 40)
1.5" (38.1mm)
Mild Steel Round Tube (Wall)
2.5" (.125) (63.5mm [3.175mm])
Aluminum Round Tube (Wall)
2.5" (.156) (63.5mm [3.96mm])
Stainless Steel Round Tube (Wall)
2.375" (.125) (60.325mm [3.175mm])
Chromolly Round Tube (Wall)
2" (.125) (50.8mm [3.175mm])
Mild Steel Solid Rod
1.25" (31.75mm)
Mild Steel Square Tube (Wall)
2" (.125) (50.8mm [3.175mm])
Power Supply
240VAC, 10A, 1ph, 50Hz
Sound level
<70db
Shipping Weight (Lbs.)
546lbs. (248kg)
Shipping Dimensions (L x W x H)
60” x 44” x 50” (1524 x 1118 x 1270mm)
*CLR will vary based upon actual material and wall thickness.
Note: The photos illustrations used in this manual are representative only and may
not depict the actual color, labeling or accessories and may be intended to illustrate technique
only.
Note: The specifications and dimensions presented here are subject to change
without prior notice due to improvements of our products.

8
8
UNPACKING AND CHECKING CONTENTS
Your Baileigh machine is shipped complete in one crate. Separate all parts from the packing
material and check each item carefully. Make certain all items are accounted for before
discarding any packing material.
Cleaning
Your machine may be shipped with a rustproof waxy oil coating and grease on the exposed
unpainted metal surfaces. To remove this protective coating, use a degreaser or solvent
cleaner. For a more thorough cleaning, some parts will occasionally have to be removed. DO
NOT USE acetone or brake cleaner as they may damage painted surfaces.
Follow manufacturer’s label instructions when using any type of cleaning product. After cleaning,
wipe unpainted metal surfaces with a light coating of quality oil or grease for protection.
WARNING:
SUFFOCATION HAZARD! Immediately discard any plastic
bags and packing materials to eliminate choking and suffocation hazards to children
and animals.
If any parts are missing, do not plug in the power cable, or turn the power switch on
until the missing parts are obtained and installed correctly.
WARNING: DO NOT USE gasoline or other petroleum products to clean
the machine. They have low flash points and can explode or cause fire.
CAUTION: When using cleaning solvents work in a well-ventilated area.
Many cleaning solvents are toxic if inhaled.
GAS

9
9
TRANSPORTING AND LIFTING
Follow these guidelines when lifting:
•The lift truck must be able to lift at least 1.5 – 2 times the machines gross weight.
•Make sure the machine is balanced. While transporting, avoid rough or jerky motion, and
maintain a safe clearance zone around the transport area.
•Use a fork lift with sufficient lifting capacity and forks that are long enough to reach the
complete width of the machine.
•Remove the securing bolts that attach the machine to the pallet.
•Approaching the machine from the side, lift the machine on the frame taking care that there
are no cables or pipes in the area of the forks.
•Move the machine to the required position and lower gently to the floor.
•Level the machine so that all the supporting feet are taking the weight of the machine and no
rocking is taking place.
INSTALLATION
IMPORTANT:
Consider the following when looking for a suitable location to place the machine:
•Overall weight of the machine.
•Weight of material being processed.
•Sizes of material to be processed through the machine.
•Space needed for auxiliary stands, work tables, or other machinery.
•Clearance from walls and other obstacles.
•Maintain an adequate working area around the machine for safety.
•Have the work area well illuminated with proper lighting.
•Keep the floor free of oil and make sure it is not slippery.
CAUTION:Lifting and carrying operations should be carried out by skilled
workers, such as a truck operator. Make sure the machine is well balanced. Choose a
location that will keep the machine free from vibration and dust from other machinery.
Keep in mind that having a large clearance area around the machine is important for
safe and efficient working conditions.

10
10
•Remove scrap and waste materials regularly, and make sure the work area is free from
obstructing objects.
•If long lengths of material are to be fed into the machine, make sure that they will not extend
into any aisles.
•LEVELING: The machine should be sited on a level, concrete floor. For stationary machines,
provisions for securing it should be in position prior to placing the machine. The accuracy of
any machine depends on the precise placement of it to the mounting surface.
•FLOOR: This tool distributes a large amount of weight over a small area. Make certain that
the floor is capable of supporting the weight of the machine, work stock, and the operator.
The floor should also be a level surface. If the unit wobbles or rocks once in place, be sure to
eliminate by using shims.
•WORKING CLEARANCES: Take into consideration the size of the material to be
processed. Make sure that you allow enough space for you to operate the machine freely.
•POWER SUPPLY PLACEMENT: The power supply should be located close enough to the
machine so that the power cord is not in an area where it would cause a tripping hazard. Be
sure to observe all electrical codes if installing new circuits and/or outlets.
ASSEMBLY AND SET UP
1. Remove the machine from the skid it was shipped on and install the casters and wheels.
2. Check the oil level and top off if necessary.
3. Read through the remainder of the manual and become familiar with the die installation and
settings as well as normal operation.
4. Position the machine as desired following the installation guidelines.
5. Follow the electrical guidelines to connect the machine to a power supply.
WARNING: For your own safety, DO NOT connect the machine to the
power source until the machine is completely assembled and you read and
understand the entire instruction manual.

11
11
GETTING TO KNOW YOUR MACHINE
A
B
C
G
H
I
K
M
J
D
E
F
L

12
12
Item
Description
Function
A
Forward Foot Pedal
Will operate the machine in the cw direction
B
Reverse Foot Pedal
Will operate the machine in the ccw direction
C
Hydraulic Reservoir
Holds the oil for operating the hydraulics.
D
Hydraulic Pump and Valve
Assembly
Provides and controls the oil flow.
E
Electric Motor
Provides the power to power the hydraulics.
F Anti-Springback Pin Assembly
Locks the rotation of the bending plate to retract the
cylinder and provide additional rotation.
G
Hydraulic Cylinder
Supply the bending force to rotate the bending plate.
H
Quick Release (shown with a
counter die installed)
For pivoting counter die away from bend die to
remove material quickly.
I
Hitch Pin
Used to secure counterdie to quick release.
J
Main Spindle And Drive Pins
(shown with a square tube
forming die installed)
For supporting and driving the forming die.
K Bend Angle Scale
A graduated scale used to indicates the bend angle
that the spindle is currently positioned at.
L Bend Angle Indicator
Indicates the bend angle that the spindle is currently
positioned at.
M
Anti-springback Lever
Disengages the lock pin from the locking teeth.
GENERAL DESIGN DESCRIPTION
You have made a practical choice in purchasing the RDB-125 Hydraulic Bending Machine. It
has been carefully built of high quality materials and designed to give many years of efficient
service. The simplicity of design and minimum effort required to operate the machine contributes
towards meeting schedules and producing greater profits.
The RDB-125 is an electric powered hydraulically operated “Rotary Draw” bending machine. To
bend material, a bending die and counter die are required. The material is hooked by the
bending dies’ hook arm and is powerfully rotated in the clockwise direction. As the bending die
rotates, the counter die forces the material to conform to the radius and shape of the bending
die.
The RDB-125 Bending Machine you have purchased is built of solid steel ensuring maximum
rigidity. Grade 8 bolts throughout provides very high rigidity and stability.
Throughout this manual are listed various safety-related descriptions for attention. These
matters for attention contain the essential information to the operators while operating, and
maintaining. Failure to follow these instructions may result in great damage to the machine or
injury to the operator.

13
13
ELECTRICAL
Motor Specifications
Your tool iswired for 240volt, 50Hz alternating current. Before connecting the tool to the
power source, make sure the machine is cut off from power source.
Considerations
•Observe local electrical codes when connecting the machine.
•The circuit should be protected with a time delay fuse or circuit breaker with a amperage
rating slightly higher than the full load current of machine.
•A separate electrical circuit should be used for your tools. Before connecting the motor to the
power line, make sure the switch is in the “OFF” position and be sure that the electric current
is of the same characteristics as indicated on the tool.
•All line connections should make good contact. Running on low voltage will damage the
motor.
•In the event of a malfunction or breakdown, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and a grounding plug. The plug must be plugged
into a matching outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
CAUTION: HAVE ELECTRICAL UTILITIES CONNECTED TO MACHINE BY
A CERTIFIED ELECTRICIAN!
Check if the available power supply is the same as listed on the machine nameplate.
WARNING: Make sure the grounding wire (green) is properly connected
to avoid electric shock. DO NOT switch the position of the green grounding wire if any
electrical plug wires are switched during hookup.
WARNING: In all cases, make certain the receptacle in question is
properly grounded. If you are not sure, have a qualified electrician check the
receptacle.

14
14
•Improper connection of the equipment-grounding conductor can result in risk of electric
shock. The conductor with insulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric
cord or plug is necessary, do not connect the equipment-grounding conductor to a live
terminal.
•Check with a qualified electrician or service personnel if the grounding instructions are not
completely understood, or if in doubt as to whether the tool is properly grounded.
•Repair or replace damaged or worn cord immediately.
Extension Cord Safety
Extension cord should be in good condition and meet the minimum wire gauge requirements listed
below:
LENGTH
AMP RATING
25ft
50ft
100ft
0-6
16
16
16
7-10
16
16
14
11-12
16
16
14
13-16
14
12
12
17-20
12
12
10
21-30
10
10
No
WIRE GAUGE
An undersized cord decreases line voltage, causing loss of power and overheating. All cords
should use a ground wire and plug pin. Replace any damaged cords immediately.

15
15
OPERATION
Bending
1. Before actually bending, several “dry runs” should be performed. This will also help to
become familiar with all of the machine functions.
2. Activate the “on/off” switch to turn the hydraulic pump on.
3. Keep hands away from the bending zone.
4. With the drive lever (cylinder fully retracted) and the ratchet wheel in the home (0°) position,
bending can take place.
5. When the machine is in the home position, engage the anti-springback lever to engage the
locking pin into the ratchet teeth.
Anti-springback lever engaged Anti-springback lever disengaged
6. Activate forward foot pedal and the drive lever will engage the first tooth of the ratchet wheel.
Hold the forward foot pedal and the cylinder will fully extend. This will rotate the bending and
ratchet plate to approximately 45 degrees of bend angle. As the cylinder is extending, the
anti-springback lock pin will be clicking as it passes by each tooth on the ratchet wheel.
CAUTION: Always wear proper eye protection with side shields, safety
footwear, and leather gloves to protect from burrs and sharp edges.
CAUTION: Keep hands and fingers clear of the dies and swing arms. Stand
to the front of the machine to avoid getting hit with the material during the bending
process. When handling large heavy materials make sure they are properly supported.

16
16
7. After full extension, press the reverse foot pedal, as the drive lever retracts, the anti-
springback lock pin will hold the ratchet wheel in place. You can restart the bending process
at any tooth on the ratchet wheel or return the machine to the home position and get the
maximum degrees per stroke. Each tooth on the ratchet wheel represents approximately 7
degrees of bend.
8. If the bend requires more degrees, increase the degrees by repeating step 6 until the desired
degrees of bend is achieved. This allows the operator to gradually reach a bend angle, on
the first set up piece. Once the proper degree of bend is achieved, document the degree (ex;
98deg = 90deg bend, 8degrees of spring back) so multiple bends to that same degree can
be accomplished.
9. When at the desired degree position the drive lever can be returned to the home position.
Material Removal
1. After reaching the desired angle, the material needs to be removed.
2. Pull the anti-springback lever (clockwise) to release tension.
3. Rotate the main bending lever fully to the right or clockwise, this will free the ratchet wheel
completely. Grab the ratchet wheel and rotate counter clockwise until it stops completely,
this is the “home” or “0°” position. The degree pointer should verify this.
4. Once at the “0°” position, engage the anti-springback lever to lock the pin. Activate the quick
release counter die lever and completely remove the material.
5. The machine is now at the “home” position and can be reloaded for the next bend.
6. Repeat previous steps.
7. With the reverse foot pedal, bring the drive lever to the home position. You will hear a
clicking as the drive lever skips over the ratchet wheel. As the drive lever approaches home,
the drive shaft slides up a ramp and disengages the ratchet wheel, stopping at home. A
slight tap of the forward pedal will relieve any tension on the drive pin allowing free
movement of the ratchet wheel.
8. At this point disengage the anti-springback lock pin. This will free the ratchet wheel. Grab the
ratchet wheel and rotate counterclockwise until it stops completely, this is the “0°” or home
position. The degree pointer should verify this.
9. For another bend on the same workpiece, restart steps from step 4 above.
CAUTION: Stand clear of the material it may spring out quickly.

17
17
DIE SELECTION AND INSTALLATION
Before any bending can take place, the
proper die set must be chosen to match the
material being bent. (EX) 1-1/2” diameter
tubing requires a die set marked 1-1/2”
tube.
A Hook Arm
B Bend Die
C Hold down Bolts
D Plastic Slide
E Counter Die Mount
F Bronze Counter Die Insert
G “0” Mark
Note: Pipe and Tube are not
the same, (see table 1) for nominal pipe
sizes. All RMD dies are color coded to
avoid confusion between pipe and tube
(see table 2).
IMPORTANT: Damaged or worn
tooling should be replaced before
attempting to bend material. This will
ensure that bends are correct and provide a
longer life to machine components.
When handling large heavy dies and/or
material, make sure it is properly lifted and
supported.
1. To install the die, slip the die over the
centering pin until the three unequally
spaced drive pins (H) engage the receiving
holes formed in the die.
Note: The die will only fit one way.
2. When the drive pins line up the die will drop
all the way down to the spindle.
A
G
F
B
C
D
E
H
H
H