BalanceBox Wings-4 User manual

order number: 481A7x
Wings
Whiteboard solution for the BalanceBox®650
Part nr. 902910-00
Installation manual

Wings
Whiteboard solution for the BalanceBox®650
Safety Instructions Tools needed
2
Needed contents for VESA assembling
Mount the VESA bracket onto the BalanceBox®650; Use the M6x16 bolts
1
A
B
A
B
CD(10x)

Wings
Whiteboard solution for the BalanceBox®650
3
Mount the VESA bracket onto the screen, you may need a spacer-set
Select the type of screw specified by your screen, M6 or M8 or M10
2
Mount the screen onto the BalanceBox®650 and align in the middle
3
=
=

Wings
Whiteboard solution for the BalanceBox®650
4
Mount the left and right profile brackets. Mount the straight side to the front, see detail B
4
Use the slot holes marked with “1”
5The top side of the profile brackets must
be mounted approximately
50 mm / 2” underneath the top of the screen
6
DETAIL B

Wings
Whiteboard solution for the BalanceBox®650
Needed contents for pre-assembling the upper aluminum profile
Pre-assemble the upper aluminum profiles; Insert one hinge on top of each profile,
Align the hinges with the end of the aluminum profile and tighten the screws
7
*
*
**
(* Only for Wings-6)
(* Only for Wings-6)
5
**

Wings
Whiteboard solution for the BalanceBox®650
6
Insert one connector plate in both profiles at the underside of the profiles,
insert one connector set and the the stop plate in the left profile
8
1
2
3
4

Wings
Whiteboard solution for the BalanceBox®650
Assemble the aluminum profiles together with the dowel pin,
they must align seamlessly, slide the connector set at the underside
and the stop plate at the top to the middle of the two profiles and tighten the screws
9
7

Wings
Whiteboard solution for the BalanceBox®650
Needed contents for pre-assembling the lower aluminum profile
Pre-assemble the lower aluminum profiles including the pen tray;
Insert one hinge at the bottom of each profile,
Align the hinges with the end of the aluminum profile and tighten the screws
* *
(* Only for Wings-6)
8
10
**
(* Only for Wings-6)

Wings
Whiteboard solution for the BalanceBox®650
9
Insert one connector plate in both profiles at the top side of the profile,
Insert one connector set in the left profile at the top side of the profile
11
1
2
3

Wings
Whiteboard solution for the BalanceBox®650
Insert two pen tray brackets in the left profile at the underside,
Insert one pen tray bracket in the right profile at the underside
12
10
1
2
3

Wings
Whiteboard solution for the BalanceBox®650
Assemble the aluminum profile together with the dowel pin, they must align seamlessly,
slide the connector set at the top and the middle pen tray bracket to
the middle of the two profiles and tighten the screws.
The other two pen tray brackets will be mounted at 200 mm / 8” form the end of the profile
13
11

Wings
Whiteboard solution for the BalanceBox®650
Mount the pen tray; slide in the pen tray profiles, one form the left and one from the right,
they must align seamlessly together. When aligned tighten the screws
14
12

Wings
Whiteboard solution for the BalanceBox®650
Align the pen tray with the middle of the aluminum profile, when aligned tighten the screws
15
13

Wings
Whiteboard solution for the BalanceBox®650
Put the pre-mounted upper aluminum profile on top of the profile brackets,
make sure the hinges are on top. Slide the connector plates at the bottom
of the aluminum profile in front of the holes of the profile brackets.
Insert the screws and align the pre-mounted profile with the middle of the screen.
When aligned tighten the screws
16
14
(Both sides!)

Wings
Whiteboard solution for the BalanceBox®650
Align the height of the profile carriers, make sure the hinges sitting on top of the screen.
First loosen the screws, align, when aligned tighten the screws
17
15

Wings
Whiteboard solution for the BalanceBox®650
Mount the pre-mounted lower aluminum profile underneath the profile brackets,
make sure the hinges are at the bottom.
Slide the connector plates at the top of the aluminum profile in front of the holes of the profile brackets.
Insert the screws. Align the pre-mounted profile with the middle of the screen.
When aligned tighten the screws
18
16
(Both sides!)

Wings
Whiteboard solution for the BalanceBox®650
Mount the whiteboards;
Wings-4: go to step 20!
Wings-6: go to step 21!
19
17
Mount the 2 white boards, each with 6 screws and close the white boards;
Go to step 23!
20
(Both sides!)

Wings
Whiteboard solution for the BalanceBox®650
Mount the 2 front white boards, each with 6 screws and close the white boards.
Go to step 22!
21
18
(Both sides!)

Wings
Whiteboard solution for the BalanceBox®650
19
Turn the back hinges forward and mount the 2 white boards.
Each with 4 screws, leave the middle hole free
22
(Both sides!)

Wings
Whiteboard solution for the BalanceBox®650
20
Open the white boards. Mount the lock knobs in the middle holes of the back white boards
23
(4x)