Ballard Designs LL307 User manual

PRODUCT NAME: Holden Floor Lamp
ITEM NUMBER: LL307
DIMENSIONS OF ITEM ASSEMBLED: 62 1/4”H x 28 1/2”W x 11”D
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE. Page 1 of 4
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN INDIA
IMPORTANT SAFETY INSTRUCTIONS:
-This Lamp has a polarized plug (one blade is wider than the other) as a feature to reduce the risk
of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fully fit in
the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an
extension cord unless plug can be fully inserted. Do not alter the plug.
-These Assembly Instructions are provided for your safety. It is important that they are read carefully
and completely before assembling this Lamp.
-This product must be installed with the applicable installation code by a person familiar with the
construction and operation of the product.
-This Lamp has been rated for up to a 40 Watt MAX Type A Bulb (Included or NOT Included) or
a 9 Watt CFL Bulb (NOT Included).
WARNING:
-Deviation from these Assembly Instructions may result in a risk of fire or electric shock.
-To reduce risk of fire, electrical shock, or personal injury, always turn off and unplug Lamp and
allow it to cool prior to replacing the bulb.
-Do not touch the bulb when the Lamp is turned on. Do not look directly at the lit bulb.
-Keep flammable material away from the lit bulb.

NOTE: Remove all parts and hardware from the box along
with any plastic protective packaging and carefully lay all the
parts out on a clean, flat surface.
DO NOT discard any contents until after assembly and
installation is complete to avoid accidentally discarding small
parts or hardware.
Recommended Location for Use: Dry Indoor Environment
Assembly Time: 5 Minutes
PARTS
Check to make sure you have the following:
INCLUDED: NOT INCLUDED:
Page 2 of 4
1-40 Watt Max Type A Bulb OR
1- 9 Watt Max CFL Bulb
1- Lamp (A) 1- Felt Pad (B)

Page 3 of 4
STEP 2:
NOTE: Before starting assembly of this Lamp, be sure it has been unplugged.
Turning the switch off is not sufficient enough.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Stem
Arm
(A)
Nut
Bolt
Remove the Nut from the Bolt on the Stem,
and adjust the wire over the Bolt.
Insert the Bolt through the Arm and adjust the
angle of Lamp (A) to the desired position.
Secure into place by screwing on the Nut
on the outside of the Arm. Turn the Nut
clockwise until fully tightened.
STEP 1:
Carefully unpack the floor lamp and remove
all packaging. Lay the product on the floor.

Page 4 of 4
STEP 3:
NOTE: Before starting assembly of this Lamp, be sure it has been unplugged.
Turning the switch off is not sufficient enough.
Screw the Stem into the Base.
NOTE: Hold the Base still and rotate the Stem
to prevent twisting the Cable. Gently pull the
Cable through the Base.
STEP 5:
Screw in Bulb. This Lamp has been rated for
up to a 40 Watt MAX Type A Bulb
(NOT Included) or a 9 Watt Max CFL Bulb
(NOT Included).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
Cleaning & Care:
To clean, wipe the Fixture with a soft, dry cloth.
Avoid the use of harsh or abrasive
chemicals as they may damage the finish
Stem
Base
(A)
(B)
Once assembled, peel off the protective
covering on the Felt Pad (B) and attach
it to the underside of the Base.
STEP 4: