Balluff BIC 1I0-IAA50-M30MI3-SM4A4A User manual

IO-Link System
BIC 1I0-IAA50-M30MI3-SM4A4A,
BIC 2I0-IAA50-M30MI3-SM4A5A
BIC 2I0-IAA50-M30MI3-BPX04-002-M45A
1
Safety Informations
Intended use
This guide describes the Balluff Inductive Coupling
System BIC … for the use in industrial environment
consisting of Base unit and Remote unit.
The electrical power is provided to the Remote unit via
air gap. Simultaneously data are transmitted in IO-Link
format.
The Base unit communicates via IO-Link protocol with
the host IO-Link master unit. The Remote unit is working
as a virtual IO-Link master unit to the connected IO-Link
device.
Read this operating guide thoroughly before
startup!
These sensors may not be used in
applications where the safety of persons
depends on device function (not a safety
component per the EU Machine Directive).
Caution!
Risk of burning on hot surfaces!
The active surface heats up even under
normal operating conditions.
Keep away hands and objects from the active
surface.
Avoid contact of metal objects on the active
surface. Fire hazard!
Approved personnel
Installation and startup are permitted only by trained
specialists.
Improper Use
Damage resulting from unauthorized actions or improper
use is not covered under the warranty and liability
provisions.
Obligations of the operator!
The equipment is an EMC Class A product. Such
devices may cause RF noise radiation. The operator
must take appropriate measures to account for this.
The operator is responsible for observing the locally
prevailing safety regulations.
Fault conditions
When defects and non-clearable faults occur in the
device, it must be taken out of service and secured
against unauthorized use.
Installation
Mutual interference
To prevent mutual interference from other Base or
Remote units, maintain the following separation
distances.
Type
A (mm)
BIC 1I0-IAA50...SM4A4A
100
BIC 2I0-IAA50...SM4A5A
100
BIC 2I0-IAA50-M30MI3-BPX04-002-M45A
100
Installation in metal
When installing in metal the specified minimum distances
from the surrounding sides of the metallic object must be
maintained, since otherwise the transmission distance
between Base and Remote will change. The
transmission distance can also be affected by the type of
metal.
Type
A (mm)
B (mm)
BIC 1I0-IAA50...SM4A4A
30
20
BIC 2I0-IAA50...SM4A5A
30
20
BIC 2I0-IAA50-M30MI3-BPX04-002-M45A
30
20
Distance D
in mm
Angle X
in °
1
18°
2
12°
3
10°
4
5°
5
0°
IO-Link Communication
Transmission rate
COM2 (38,4 kBaud)
Frame type
1
Min cycle time
3 ms
Process data cycle
< 200 ms
SIO Mode
no
IO-Link Revision
1.0
Masterporttyp
A
Processdata in
11
Processdata out
0
Errors
Error Code
Additional Code
device application error
Index not available
0x80
0x11
device application error
SubIndex not available
0x80
0x12

IO-Link System
BIC 1I0-IAA50-M30MI3-SM4A4A,
BIC 2I0-IAA50-M30MI3-SM4A5A
BIC 2I0-IAA50-M30MI3-BPX04-002-M45A
2
IO-Link-Communication
Process data image
Byte 0 to 9
Byte 10
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Process data of the connected IO-Link Device
0
0
0
0
Error „Supply Remote“
Error „Short Remote“
Error “Inzone”
Error “Com”
*unused data is cleared by 0.
Error “Supply Remote”
Supply voltage at Remote is lower than 18V
Error “Short Remote”
Short circuit detected on Remote Com-interface
Error “Inzone”
No Remote detected
Error “Com”
No IO-Link device detected
Note, tip
Process data update time is max. 200ms
Parameter data
DPP
SPDU
Object name
Length
Range
Default value
Index
Index
Sub Index
Identification Data
0 x 07
Vendor ID
2 Byte
read only
0 x 0378
0 x 08
0 x 09
Device ID
3 Byte
0 x 050602
0 x 0A
0 x 0B
0 x 10
0
Vendor name
8 Byte
BALLUFF
0 x 11
0
Vendor text
16 Byte
www.balluff.com
0 x 12
0
Product name
34 Byte
BIC 1I0-IAA50-M30MI3-SM4A4A
0 x 13
0
Product ID
21 Byte
BIC0053
0 x 14
0
Product text
34 Byte
BIC IOL Base extended
0 x 16
0
Hardware Revision
3 Byte
0 x 17
0
Firmware Revision
3 Byte
Parameter
Data
0 x 40
64
0
1 - 16
Direct Parameter Page
Remote Device
16 Byte
Events
Class / Qualifier
Code (high + low)
Mode
Type
Instance
appears
Error
AL
Device
Hardware
supply
Supply low voltage
U2 = supply + 24 V
0 x C0
0 x 30
0 x 03
0 x 5000
0 x 0100
0 x 0010
0 x 0002
0 x F3
0 x 5112
disappears
Error
AL
Device
Hardware
supply
Supply low voltage
U2 = supply + 24 V
0 x 80
0 x 30
0 x 03
0 x 5000
0 x 0100
0 x 0010
0 x 0002
0 x B3
0 x 5112

IO-Link System
BIC 1I0-IAA50-M30MI3-SM4A4A,
BIC 2I0-IAA50-M30MI3-SM4A5A
BIC 2I0-IAA50-M30MI3-BPX04-002-M45A
3
Technical Data, Connection
Base
Base
Power (M12, 4 pin-male plug)
PIN
Signal
1
+24 V
2
NC
3
GND, 0V
4
C/Q, IO Link
Electrical data Base
Operating voltage range
24 V DC ±10%, by EN 61131-2
Current consumption
max 1 A
Leerlaufstrom
max. 100 mA
Overload protection
Yes
Remote
Connector SM4A4A
Cable BPX04-002-M45A
Remote
Power (M12, 4 pin-female plug)
PIN
Signal
1
+24 V
2
NC
3
GND, OV
4
C/Q, IO Link
5
NC
Electrical data Remote
Output Voltage
24 V DC ±5%
Output current
500 mA
Short circuit proof
yes
Max. peak current
max. 800 mA
Data set ready
< 100 ms
Indication
Base
Base
Indicator
Function
Green static
Module supply OK. No IO-Link communication
Green inverse
blinking
IO-Link communication
between Master and Base OK
Red blinking
Remote not detected
Red off
Remote present IO-Link Communication OK
Red static
Connection Base and Remote OK
No IO-Link communication to connected
Device
Remote
Remote
Indicator
Function
Green static
Inside working rage,
Communication between Remote and IO-Link
device OK
Green blinking
No IO-Link device present

881882 E Edition 1203 Revised Edition 1112 Subject to modification
www.balluff.com
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Deutschland
Tel. [phone]
Fax [phone]
[email protected]
www.balluff.com