Balt Jpm-1 User manual

1234567890123456789012345678901212345678901234567890123

Assembly Instructions

JPM-1

Just Pure Magic

Adjustable Printer Stand

P-1 Leg Frame 2 EA

P-2 Back Stability Panel 1 EA

P-3 Long Metal Plates 2 EA

P-4 Short Metal Plates 4 EA

P-5 Forms Basket 1 EA

P-6 Forms Rack 1 EA

A FlatHeadScrew 12EA

A1 SquareShoulderScrew 4 EA

B InteriorThreadedPost 4 EA

C Leveling Feet 4 EA

D 2” Locking Casters (for Front) 2 EA

E 2” Casters (for Back) 2 EA

F Allen Wrench 1 EA

G Caster Wrench 1 EA

H Cable Clips 4 EA

J Wing Nuts 8 EA

K Flat Washer 8 EA

Part Drawing Description Qty

Just Pure Magic Printer Stand JPM-1

Hardware List

Part Drawing Description Qty

Do not use unless all screws are tight. At least

every six months, check all screws to be sure they

are tight. If parts are missing,

broken, damaged, or worn, stop use of the product

until repairs are made by your dealer using factory

authorized parts.

P-1

P-2

To Assemble:

1. Identify and Separate all the Parts and

Hardware.

2. Attach Back Stability Panel (P-2) to 2

Leg Frames (P-1) using 4 Flat head

Screws (A) and 4 Interior Threaded Posts

(B) as shown in illustration # 1.

(Do not tighten the screws all the way)

3. Attach 4 Leveling feet (C) or Casters to

the Leg Frames [If casters, 2 Locking

casters (D) in the front and 2 Casters (E)

in the back. Tighten the Casters using

Caster Wrench (G)]

Illustration # 1

JPM-1 Just Pure Magic

Adjustable Printer Stand Assembly Diagram

4. Attach 2 Long Metal Plates (P-3)

and 4 Short Metal plates (P-4)

to the Leg Assembly (P-1)

using 4 Square Shoulder

Screws (A1), Flat Washers (K)

and Wing Nuts (J).

See back page for different

options. [Option #3 shown here.]

Note: Long Metal Plates should be

attached with Channel side down,

and Short Metal Plates with the

channel side up.

5. Install Forms Basket

(P-5) in the holes on

the Leg frame assy

(P-1) as shown in

illustraion # 3.

6. Place Forms Rack (P-6)

on lower part of Leg

Frame Assembly (P-1).

7. Tighten all screws

securely using the

Allen Wrench (F).

P-4

P-3

P-1

P-5

P-6

Illustration # 2

Illustration # 3

P-1

Should you require assistance during assembly,

please call our Customer Service Department

Monday - Friday 8 a.m. - 5 p.m. Central Standard Time

Toll-Free Customer Service 1-800-749-2258

The Balt product you have purchased is guaranteed against material and workmanship defects.

This guarantee extends 1 year from date of purchase. Should this product fail to function satisfactorily under normal

use due to defect or imperfection, the defective part or product will be replaced.

Damage caused by common carriers during shipment is not included in this guarantee.

This guarantee sets forth all applicable guarantees and remedies. No other warranty, expressed or implied shall apply.

Failure to follow instructions found in Important Information Section of Owner Sheet shall void the guarantee.

Consequential or incidental damages and or costs are not refundable.

Important

1. FOR LARGE PRINTERS

Attach 2 Long Metal Plates (P-3)

[through outer holes] and 4 Short

Metal plates (P-4) to the Leg Frames

using 4Screws (A1), 4Flat Washers

(K) and 4 Wing Nuts (J).

Note: Long Metal Plates should be

attached with Channel side down,

and Short Metal Plates with the

channel side up. 2. FOR EXTRA STABILITY

WITH LARGE PRINTERS

Attach the Long Metal Plates (P-3)

and Short Metal Plates (P-4) same

as for the large Printers. Then attach

Short Metal Plates through the inner

holes on the Long Metal Plate using

4 Screws (A1), 4 Flat Washers (K)

and 4 Wing Nuts (J) for added

stability.

3. FOR NARROW PRINTERS

Attach 2 Long Metal Plates (P-3)

[through outer holes] to the Leg Frames

using 4 Screws (A), 4 Flat Washers (K)

and 4 Wing Nuts (J).

Then attach 4 Short Metal Plates (P-4)

through the inner holes on the Long Metal

Plateusing 4 Screws(A1), 4 FlatWashers

(K) and 4 Wing Nuts (J).

P-4 P-3 Outer Hole

Outer Hole

Inner Hole

P-4

P-3

P-4 P-3

OPTION # 2

OPTION # 1

OPTION # 3

JPMasm.pm6-07/05/00

Four top plates adjust independently to

accommodate teh smallest to largest

printers.

Standard with one-piece bottom forms

rack and printout receiving basket.

This can hold two full boxes of forms.

2” casters included.

Ships UPS.

21"

For more information

1-800-749-2258

Shipping Information

2.0 Cubic Feet

24 lbs.

27”

25”

5”

JPM-1

Just Pure Magic

Adjustable Printer Stand

27" w/ glides

24-35” (adj)

6-29” (adj)

24"

Table of contents

Other Balt Rack & Stand manuals

Balt

Balt iTeach 2 User manual

Balt

Balt 27624 User manual

Balt

Balt 33550 User manual

Balt

Balt 27534 User manual

Balt

Balt 90377 User manual

Balt

Balt 34429 User manual

Balt

Balt 27542 User manual

Balt

Balt Lumina Flat Panel Stand User manual

Balt

Balt PBL User manual

Balt

Balt BLT-23701 User manual

Popular Rack & Stand manuals by other brands

Pannier

Pannier Single Post Frameless Assembly and installation instructions

Vivotek

Vivotek Fixed Dome Series installation guide

NCR

NCR 7761-K130 Kit instructions

Vivotek

Vivotek AF101 quick start guide

Zico

Zico Quic-Mount VM-3RS-D Parts and instruction manual

OYPLA DIY

OYPLA DIY 3546 user manual

Overland Storage

Overland Storage SnapServer 2000 Series Installation

QEP

QEP Vitrex MIXSTAND manual

Thule

Thule HangOn 972 Fitting instructions

TORADO

TORADO Prime TO5001 Fitting instructions

Rehadapt

Rehadapt 16.1220 Assembly instructions

LEITZ

LEITZ Complete Charging Desk Stand operating instructions

Wheelock

Wheelock Cooper ET70-24MCC installation instructions

U-Line

U-Line H-4203 Assembly instructions

Ergo Desktop

Ergo Desktop KANGAROO JUNIOR Assembly instructions

Southern Telecom

Southern Telecom Packard bell instruction manual

CommScope

CommScope SYSTIMAX iPatch 600A instruction sheet

Haugen

Haugen MFSH-6 Installation and safety manual

Balt JPM-1 User manual

Popular Rack & Stand manuals by other brands