Bano 5970S2-EL User manual

EN
INSTALLATION INSTRUCTIONS
BANO AS BANO AB BANO A/S
Utstillingsplassen 3
6823 Sandane-Norge
Phone: [phone]
[email protected]
www.bano.no
Hammarby Allé 91
120 63 Stockholm - Sverige
Phone:[phone]
[email protected]
www.bano.se
Møllehaven 8
4040 Jyllinge - Danmark
Phone: [phone]
[email protected]
www.bano.dk
5970S2-EL Bano height adjustable toilet/cistern, electrical
5970-MA Bano height adjustable toilet /cistern, manual
BANO HEIGHT ADJUSTABLE TOILET/CISTERN
Bano provides a 3-year warraty against
manufacturing defects: i.e.if such defects
appear within 3 years of installation,
customers can replace the defective item
with a corresponding properties.
Award for design excellence
Norwegian Design Council
.
B
R
A
N
S
C
H
R
E
G
L
E
R
S
Ä
K
E
R
V
A
T
T
E
N
I
N
S
T
A
L
L
A
T
I
O
N
mounting instructions
2016:1
Accepted
Rev: 06.april.2017

(2/16)
TABLE OF CONTENTS:
Page 3 Introduction
Page 3 Compliance with EU directive
Page 3 Accessories
Page 4 Technical data
Page 5 Interface
Page 6 Contents, loose parts
Page 7-15 Installation
Page 16 Wiring diagram (ONLY 5970S2-EL)
Page 17 Operating the height adjustment

(3/16)
Introduction
Bano’s height-adjustable cisterns can be adjusted either manually with a crank or electrically.
This lightens the carer’s work load because one person can quickly and easily adjust the height
of the toilet to fit the users needs. The height of the toilet can be adjusted from 410 to 610 mm.
The cistern is supplied either with a manual hand crank or with electrical height adjusters.
With simple steps the height of the toilet and the WC grab bars can be adjusted. For bathrooms
with external pipes an extension for the cistern must be used. For more information see Bano interface
on www.bano.no
Electrical adjustment is operated by a button on the top of the cistern. For manual adjustment, use the
accompanying crank.
Compliance with EU directive:
This product is CE branded and meet the provisions in the EU safety requirements laid down in the Medical
Devices Directive 93/42/EEC, class 1.
See also:
EN 12182: 2012: Assistive products for persons with disability
EN 14055: 2011: WC and urinal flushing cisterns
EN 997: 2013: Sanatary appliances, washbasins
Accessories:
Installed with a Bano toilet bowl 530 or Bano toilet bowl 700 mm (5965/5975), and toilet grab bars (5603/5604).
With external pipes, please use an extension (5970-22/5970-23), either 50 mm or 100 mm.
Article numbers:
5965 WC 530 mm
5975 WC 700 mm
5603 Grab bars WC 900 mm
5604 Grab bars WC 700 mm
5970-22 Extension 50 mm
5970-23 Extension 100 mm
5970-03 Toilet seat, white
5970-06 Toilet seat, grey

Technical data:
Product name : Height adjustable toilet (cistern) with manual height-adjustment
Product number : 5970-MA
Height-adjustment : 200 mm (from 410 mm to 610 mm)
Materials : Main frame: Corrosion treated steel, El galvanized
Cover: ABS/ PMMA plastic, colour code RAL 9016.
Max weight load : Static load, toilet: 500 kg
Static load, grab bars: 250 kg
Max weight load, height-adjustment: 200 kg
Producer : BANO AS
Email: [email protected]
Phone: [phone]
Web site: www.bano.co.uk
Product name : Cistern with electrical height-adjustment
Product number : 5970S2-EL
Height-adjustment : 200 mm (from 410 mm to 610 mm)
Materials : Main frame: Corrosion treated steel, El galvanized
Cover: ABS/ PMMA plastic, colour code RAL 9016.
Max weight load : Static load, toilet: 500 kg
Static load, grab bars: 250 kg
Max weight load, height-adjustment: 300 kg
U In : 230V ~ /50 Hz
I In : Max 5A
U Out : 24V-, max. 100VA IPX5
Int. : 5%, max. 1 min./19 min.
Producer : BANO AS
Email: [email protected]
Phone: [phone]
Web site: www.bano.co.uk
(4/17)

NOTE! PLUMBING:
Water outlet on left side as shown in illustration.
Placement of stopvalve: because of moving parts
when adjusting the cistern’s height the stop valve
must be placed exactly as is shown on the illustration.
Stopvalves are turned as shown on drawing.
Concerning water; finish with stop valve with 1/2”
external threads (G15). (Threads pointing up)
Drainpipe in floor: Ø110 drainpipe without cuff is
finished 40 mm above floor.
NOTE! ELECTRICAL:
Electrical innstallation only for products with electrical
height adjustment.
Electrical outlet on right side as shown in illustration.
Electrical cable/ pipe is pulled 500 mm from wall
and placed 200 mm above finished floor and 100 mm
from the center of the cistern’s drain.
Electritian connects IP44-box aftrer the cistern is
installed. (IP44-box not included).
NOTE! ELECTRICAL:
This ONLY applies to 5970S2-EL with electrical
height-adjustment.
Finished floor
NOTE! CONSTRUCTION:
Loadtested untill 500 kg.
Min.: 48x198 board
Nailingstrips must be placed flush against wall material.
Nailing strips are indicated with shaded area.
1
2
(5/17)
Interface:

(6/18)
Contents (loose parts):
9750 White caps for installing, toilet
9716 Installation bolts, toilet
ISO 7380 M4x12
9700 Flush button, cistern
9712 9712 Water pipe, cisterne
9755 Krank (ONLY for 5970-MA)
9751 Nut (ONLY for 5970-MA)
Control for height adjustment (ONLY for 5970S2-EL)

(7/17)
Installing the cistern:
Install the drain pipe in the floor drain by using the provided double jetcoupling. Check that the holder
9749 is mounted on the flexible drain pipe before proceeding.
Place cistern frame against the wall and ensure that it is level. Mark all the screw holes. (8 pieces).
The cistern must be raised up or down using the crank to get to the fixing holes during installation.
Remove the frame and follow the procedure below.

(8/17)
Adjustment in case of uneven floor:
If uneven floors (eg. slope towards the drain) cistern can be adjusted using the adjustment screws
found on the bottom of each side. Adjust from above with hex key, M5.

(9/17)
Fixing to wall:
Make sure never to perforate wet walls completely. Clean the holes after drilling. Make sure to use
sealant approved for application on wet walls. See illustration.
Please note that the product guarantee only applies when the wall and screws are dimensioned
according to «Byggebransjens Våtromsnorm» and Bano interface for products mounted in Norway.
For products mounted in other countries, please note that the product guarantee only applies when
wall and screws are dimensioned according to national guidelines/regulations and Bano interface.
Tiled wooden wall:
Make sure never to perforate wet walls completely. Drill holes with a 10 mm drill bit through the tiles
only. Clean and fill the hole with sealant approved for application on wet walls. Se illustration.
Tiled concrete wall:
Drill holes using a 12 mm drill bit through the tiles only. Switch to a 10 mm drill bit for further drilling
through the concrete. Fill the hole with sealant, place a nylon plug in the hole and fill the plug with
sealant. Se illustration.
Other wall materials (bathroom boards, vinyl):
Make sure never to perforate wet walls completely. Drill holes which are dimentioned for said type
of wall. Fill the hole with sealant, place a nylon plug in the hole and fill the plug with sealant.
See illustration.
Drill holes and fix the frame to the wall. Make sure the screws are fastened withing the nailing strips,
see Bano interface page 5.
FIXING WOODEN WALL
FIXING CONCRETE WALL
Plaster walls Concret Wood Tiles

4X
(10/17)
4X
Step 1:
Lower the cistern to the bottom position and secure to the
wall with appropriate screws for the wall. Bano recommends
M8 French wood stainless steel screws. For concrete Bano
recommends French wood screws DIN571 in combination
with a nylon plug.
Step 2:
Raise the cistern to the top position and secure to the wall with
appropriate screws for the wall. Bano recommends M8 French
wood DIN571 stainless steel screws. For concrete Bano
recommends French wood screws DIN571 M8 in combination
with a nylon plug.
After mounting the cistern at the wall applide silicones at all three
sides around the frame and up against the wall. Applide silicone
round the frame against the floor on all three sides, but leave a
corner, closest to the shower area/ lowest point open 4 cm on
each side.
Silicone must be on before mounting main cover and toilet.
Fixing to wall:

(11/12)
Adjusting installation bolts:
Adjust the length of the installation bolt. Each bolt is screwed into the frame and secured with a M12 nut
in the back. Make sure the shaft runs freely without coming into contact with nut or threaded rod.

(13/17)
Installing flush pipe and drain pipe:
Adjust the length of the flushpipe according to the
type of toilet.
Install drain pipe and holder before installing the
toilet. We reccomend raising the cistern to the
highest position when installing the toilet.
Please check that the water supply pipe is installed,
and the valve open, before mounting the cover.
Flush pipe length:
5965 Toilet bowl 530 mm: 170 mm
5970 Toilet bowl 700 mm: 330 mm
ISO 7380 M4x12

(14/17)
Cover and cranck:
Mount the main cover and remove the protection film
from all plastic parts.
Mount the crank on one side, and the nut on the other.

(15/17)
Installing the flush button:
95
138
165
AB
Break the green and white
adjustment pin by
95 mm box (B)
The left stick is cut on half length.

(16/17)
Installing the grab bar:
Toilet grab bar (5603/5604) on each side of the cistern.

(17/17)
Wiring diagram (ONLY 5970S2-EL):
Parts List
MINUS / LoPLUS / Lok.DESCRIPTIONPART NUMBERQTYPOS
Kontrolboks, CB8TCB8001T60-0010
11
Motor for LA28, IP66M281015-0012
Håndbetjeningskabel
0015751-A13
2
2
3
3
4
4
5
5
6
6
Date
Confdential: Property of LINAK DK A/S. Silkeborg.
Not to be handed over to, copied or used by third party.
LINAK Danmark A/S
Mønstedsvej 9
DK-8600 Silkeborg
TLF. 86803611 FAX [phone]
Subject: Product:
No:
Date: change no:
cons:
Matr: LINAK no:
General tolerance:
Geometrical tolerance:
Suface character:
Indgår i tegnings N
Rev. From. Date
A
B
C
D
E
F
G
H
Papirformat:
DKJC
11-09-2013
CB8T-system
M28-singlemotor
MEDI-0000-0004-D
BANO
A3
1 2
3
100 mm
1 2
3
4
12
3
4

Operating the height-adjustment:
5970S2-EL: The height on the WC is adjusted by using the button on the top of the cistern.
The cistern is raised by pushing the “up”-button and lowered by using the “down”-button.
The cistern stops as soon as the button is released.
5970-MA: When using the manual height-adjustment the crank installed on the side of the cistern is used.
This crank can be mounted on both sides of the cistern. The crank must be pushed in before it can be used
and is therefor safe to use with demetia patients.The crank can easily be removed and replaced with a nut.
(Contact Bano for more information)