Barco Nio MDNC-3521 SNES User manual

ENABLING BRIGHT OUTCOMES
MDNC-3521 SNES MDNC-3521 SPES
MDNC-2521 SNES MDNC-2521 SPES
User Guide
Nio 2MP / 3MP LED Display

Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com

3R5915130 /05 Nio 2MP / 3MP LED Display
1 Welcome!.......................................................................................................................................................................................................... 5
1.1 What's in the box................................................................................................................................................................................6
1.2 At a glance.............................................................................................................................................................................................6
1.3 Compatible Barco system components..............................................................................................................................10
2 Installation and setup......................................................................................................................................................................... 11
2.1 Stand base plate mounting........................................................................................................................................................12
2.2 Single workstation setup.............................................................................................................................................................12
2.3 Dual workstation setup with KVM switch ...........................................................................................................................14
2.4 QAWeb Enterprise registration ...............................................................................................................................................17
2.5 VESA-mount installation.............................................................................................................................................................17
3 Daily operation .........................................................................................................................................................................................21
3.1 Recommendations for daily operation ................................................................................................................................22
3.2 Shortcut bar........................................................................................................................................................................................22
3.3 On/Off switching ..............................................................................................................................................................................23
3.4 KVM input switching......................................................................................................................................................................23
3.5 OSD menu access and use ......................................................................................................................................................24
4 Advanced operation............................................................................................................................................................................25
4.1 OSD menu language ....................................................................................................................................................................26
4.2 OSD menu position........................................................................................................................................................................26
4.3 OSD menu orientation..................................................................................................................................................................26
4.4 OSD menu timeout.........................................................................................................................................................................26
4.5 Power lock function........................................................................................................................................................................27
4.6 DPMS mode.......................................................................................................................................................................................27
4.7 Hibernate .............................................................................................................................................................................................28
4.8 Presence sensor .............................................................................................................................................................................28
4.9 Dry mode .............................................................................................................................................................................................29
4.10 Luminance target ............................................................................................................................................................................29
4.11 Color temperature/white tint......................................................................................................................................................30
4.11.1 Color temperature.......................................................................................................................................................30
4.11.2 Color coordinates........................................................................................................................................................30
4.12 Display function................................................................................................................................................................................31
4.13 Ambient Light Compensation (ALC).....................................................................................................................................31
4.14 Reading room....................................................................................................................................................................................32
4.15 Embedded QA .................................................................................................................................................................................. 32
Table of contents

R5915130 /05 Nio 2MP / 3MP LED Display4
4.15.1 DICOM status report .................................................................................................................................................33
4.15.2 DICOM compliance check .....................................................................................................................................33
4.15.3 DICOM calibration ...................................................................................................................................................... 33
4.15.4 DICOM error threshold.............................................................................................................................................34
4.15.5 Reset DICOM calibration........................................................................................................................................34
4.16 Image source.....................................................................................................................................................................................34
4.17 KVM switch.........................................................................................................................................................................................35
4.18 Grayscale conversion modes...................................................................................................................................................35
4.19 System info.........................................................................................................................................................................................36
4.20 Calibration status ............................................................................................................................................................................36
4.21 Maximum luminance demo .......................................................................................................................................................36
5 Cleaning the display ...........................................................................................................................................................................37
5.1 Cleaning instructions.....................................................................................................................................................................38
6 Repackaging instructions ..............................................................................................................................................................39
6.1 Repackaging instructions...........................................................................................................................................................40
7 Important information.........................................................................................................................................................................45
7.1 Safety information...........................................................................................................................................................................46
7.2 Cybersecurity ....................................................................................................................................................................................48
7.3 Environmental information.........................................................................................................................................................48
7.4 Regulatory compliance information......................................................................................................................................50
7.5 EMC notice ......................................................................................................................................................................................... 51
7.6 Explanation of symbols................................................................................................................................................................53
7.7 Legal disclaimer...............................................................................................................................................................................57
7.8 Open source license information ...........................................................................................................................................57
7.9 Technical specifications...............................................................................................................................................................58

5R5915130 /05 Nio 2MP / 3MP LED Display
1.1 What's in the box ............................................................................................................................6
1.2 At a glance.....................................................................................................................................6
1.3 Compatible Barco system components...........................................................................................10
Welcome! 1

R5915130 /05 Nio 2MP / 3MP LED Display6
1.1 What's in the box
Overview
• Nio 2MP / 3MP LED Display LED Display
• Stand base plate
• Printed user guide
• Documentation disc, containing different languages of this user guide and the Barco "Display Controller
and Intuitive Workflow Tools" user guide.
• System sheet
• Cables for mains, video and USB
• External power supply
If you ordered a Barco MXRT display controller, it is also in the box together with its accessories. A dedicated
user guide is available on the documentation disc.
Keep your original packaging. It is designed for this display and is the ideal protection during
transport and storage.
The user guides are also available on www.barco.com/support
If your product arrived with shipping damage or missing parts, please refer to the instructions in our
knowledge base article ‘3727’ at www.barco.com/support/knowledge-base/3727 for further
assistance.
1.2 At a glance
Product overview
2
3
5
7
6
7
4
89
1
10
Image 1–1
Welcome!

7R5915130 /05 Nio 2MP / 3MP LED Display
1. Presence sensor
The presence sensor detects if somebody is present in front of the display (within a
range of approximately 90 cm) and will set the backlight to a minimum if nobody is
present after a time-out (configurable in the OSD menu). When a person is detected, the
display will switch to normal operation again. See “Presence sensor”, page 28 for more
information.
2. Ambient light sensor and status LED
• Off: Display not powered (mains cable unplugged),or display is in normal operation
• Fast blinking amber: Display is in suspend mode
• Slow blinking amber: Display is in standby mode
• Steady amber: Display is in hibernate mode
• Heartbeat amber: Display manually switched off via the jog dial
3. Front sensor
CAUTION: To avoid permanent damage to the product, never use the front sensor to
hold a paper, radiological film or any other object.
4. VESA mount cover
5. Side USB-A 2.0 downstream connector
6. Side USB-A 2.0 downstream connector (chargeable)1
7. Connector cover
8. Jog dial
•Press:Switch on the display, activate shortcut bar, go into (sub)menus, confirm
adjustments and selections
•Turn left/right: Switch on the display, activate shortcut bar, scroll through (sub)
menus, change values, make selections
•Press and hold for approximately 3 seconds: Switch off the display while no OSD
menu is on the screen, abort DICOM compliance check/DICOM calibration
9. Stand locking mechanism
10. Cable routing channels
Connectors
Two USB connectors are available on the side of the display. To access the bottom connectors, gently pull the
bottom of the connector cover away from the display.
Welcome!
1. Charging is only possible when DPMS mode with USB charging is enabled, or when DPMS is completely disabled (see “DPMS
mode”, page 27).

R5915130 /05 Nio 2MP / 3MP LED Display8
Image 1–2
Following connectors are available:
DP IN 1 DP IN 2 DP OUT
USB
DOWN
USB
UP 1
USB
UP 2 DC IN
1 2 35 6 7 89
SERVICE
4
Image 1–3
1. DisplayPort IN 1 (also main for KVM switching)
2. DisplayPort IN 2 (also secondary for KVM switching)
3. DisplayPort OUT (Manufacturing test only)
4. Service (Service purpose only)
5. USB-A 2.0 downstream connectors (3x)
6. USB-B 2.0 upstream connector 1 (Main)
7. USB-B 2.0 upstream connector 2 (Secondary)
8. +24V DC mains power input
9. Kensington security slot
Display position adjustment
After unpacking, you can safely tilt, swivel and pivot the display to your preferred position.
Welcome!

9R5915130 /05 Nio 2MP / 3MP LED Display
Image 1–4
To adjust the height of the display, first move the slider at the back of the stand to the unlock position. Then
you can raise or lower the display as desired.
Image 1–5 Image 1–6
The height can be locked only in the lowest position, even though the slider at the back of the stand
can be moved to the lock position at any height of the display.
Welcome!

R5915130 /05 Nio 2MP / 3MP LED Display10
1.3 Compatible Barco system components
Overview
Following Barco components are compatible with your Nio 2MP / 3MP LED Display LED Display:
• QAWeb Enterprise Agent version 2.11 or later.
• QAWeb Enterprise for DIN 6868-157-1.3.3 or later.
• MXRT-x700 generation display controllers.
The previous generation MXRT-x600 display controllers are also supported.
• MXRT driver version 10.194.3.1 or later.
Welcome!

11R5915130 /05 Nio 2MP / 3MP LED Display
2.1 Stand base plate mounting............................................................................................................12
2.2 Single workstation setup ...............................................................................................................12
2.3 Dual workstation setup with KVM switch .........................................................................................14
2.4 QAWeb Enterprise registration ......................................................................................................17
2.5 VESA-mount installation ...............................................................................................................17
Installation and
setup 2

R5915130 /05 Nio 2MP / 3MP LED Display12
2.1 Stand base plate mounting
To mount the stand base plate
1. Put the display face down on a clean and soft surface. Be careful not to damage the panel.
Tip: The stand base plate can also be mounted while the display is still safely positioned in the
bottom buffer of box. See “Repackaging instructions”, page 40 for more information.
2. Attach the stand base plate to the pillar by fixing the dedicated screw as shown below.
Image 2–1
2.2 Single workstation setup
About
In this setup, the display is connected to a single workstation with a DisplayPort cable. When connecting a
USB cable from your display to the workstation, you can control the workstation with a keyboard and mouse
connected to the display.
USB
DisplayPort
USB
Image 2–2
Installation and setup

13R5915130 /05 Nio 2MP / 3MP LED Display
Install the display controller
Before you connect your display with the workstation, make sure to have a suitable2display controller installed
in the workstation.
The Nio 2MP / 3MP LED Display operates at its full specifications when driven by a Barco MXRT
display controller and MXRT driver (which also includes the Barco Intuitive Workflow Tools). If
you ordered a MXRT display controller, it is included in the box of your display.
For more information and installation instructions, please check the Barco “Display Controller and
Intuitive Workflow Tools” user guide on the included documentation CD, or at www.barco.com/
support.
Connect the cables
1. Remove the connector cover.
2. Connect one of the DisplayPort inputs (DP IN 1 or DP IN 2) with the DisplayPort output on the workstation.
3. Connect the main USB upstream connectors (USB UP 1) with a USB host on the workstation to make use
of QAWeb Enterprise or a peripheral (keyboard, mouse, touchpad, etc.) connected to one of the display’s
USB downstream connectors.
4. Connect a keyboard and mouse (or another peripheral used to control the workstations) with the USB
downstream connectors of the display. Three USB downstream connectors are available in the connector
compartment.
Note: When DPMS mode with USB charging is enabled (see “DPMS mode”, page 27) and
hibernate is enabled (see “Hibernate”, page 28), you can easily awaken your system from
hibernate with a mouse/keyboard connected to the display.
When DPMS mode without USB charging is enabled (see “DPMS mode”, page 27) and hibernate
is enabled (see “Hibernate”, page 28), you can only awaken your system from hibernate by
pressing the jog dial, or with a mouse/keyboard connected to the workstation (and not to the
display).
5. Connect the supplied external DC power supply to the power input on the display.
6. Route all cables through the cable clips in the connector compartment.
7. Re-install the connector cover: slide the top of the cover in the available recesses, then push the bottom of
the cover back into position.
8. Route all cables through the routing channels in the stand of your display.
9. Connect the external DC power supply to a grounded power outlet by using one of the power cables
included with the display.
Installation and setup
2. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support
> Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)

R5915130 /05 Nio 2MP / 3MP LED Display14
DP IN 1 DP IN 2
DP OUT
USB
DOWN
USB
UP 1
USB
UP 2
DC IN
SERVICE
Image 2–3
To switch between different image sources, see “Image source”, page 34 for more information.
Power on the display system
1. Press/Turn the jog dial to activate your display.
2. Switch on the workstations connected to your display.
Your display will be running in a basic video mode at a default refresh rate when first time starting up.
Install the MXRT driver and Intuitive Workflow Tools
When using a Barco MXRT display controller, install the MXRT driver and Intuitive Workflow Tools on the
connected workstation. Barco’s Intuitive Workflow Tools are designed to increase visibility of subtle details,
improve focus during reading sessions, and accelerate workflow.
1. Download the latest MXRT driver and Intuitive Workflow Tools from www.barco.com/mxrt.
2. Install the MXRT driver and Intuitive Workflow Tools as described in the Barco “Display Controller and
Intuitive Workflow Tools” user guide on the included documentation CD, or at www.barco.com/support.
2.3 Dual workstation setup with KVM switch
About
In this setup, the display is connected to two different workstations, each with one DisplayPort cable. When
connecting a USB cable from your display to each of the two workstations, you can control both workstations
with a single keyboard and mouse connected to the display. Switching the video and control signals between
the two workstations is done with the KVM switch operated via the OSD menu.
Installation and setup

15R5915130 /05 Nio 2MP / 3MP LED Display
USB
DisplayPort
USB
DisplayPort
USB
Image 2–4
Barco suggests to have QAWeb Enterprise installed on only one of both workstations. When both
workstation would have QAWeb Enterprise installed, switching KVM inputs would trigger a
Configuration Change event, causing the display to disappear from the workstation in QAWeb
Enterprise.
Install the display controller
Before you connect your display with the workstation, make sure to have a suitable3display controller installed
in the workstation.
The Nio 2MP / 3MP LED Display operates at its full specifications when driven by a Barco MXRT
display controller and MXRT driver (which also includes the Barco Intuitive Workflow Tools). If
you ordered a MXRT display controller, it is included in the box of your display.
For more information and installation instructions, please check the Barco “Display Controller and
Intuitive Workflow Tools” user guide on the included documentation CD, or at www.barco.com/
support.
Connect the cables
1. Remove the connector cover.
2. Connect DisplayPort input 1 (DP IN 1) with the DisplayPort output on workstation 1.
3. Connect the main USB upstream connector (USB UP 1) with a USB host on workstation 1.
4. Connect DisplayPort input 2 (DP IN 2) with the DisplayPort output on workstation 2.
5. Connect the secondary USB upstream connector (USB UP 2) with a USB host on workstation 2.
6. Connect a keyboard and mouse (or another peripheral used to control the workstations) with the USB
downstream connectors of the display. Three USB downstream connectors are available in the connector
compartment.
Note: When DPMS mode with USB charging is enabled (see “DPMS mode”, page 27) and
hibernate is enabled (see “Hibernate”, page 28), you can easily awaken your system from
hibernate with a mouse/keyboard connected to the display.
When DPMS mode without USB charging is enabled (see “DPMS mode”, page 27) and hibernate
is enabled (see “Hibernate”, page 28), you can only awaken your system from hibernate by
pressing the jog dial, or with a mouse/keyboard connected to the workstation (and not to the
display).
7. Connect the supplied external DC power supply to the power input on the display.
8. Route all cables through the cable clips in the connector compartment.
9. Re-install the connector cover: slide the top of the cover in the available recesses, then push the bottom of
the cover back into position.
10. Route some or all cables through the routing channels in the stand of your display.
11. Connect the external DC power supply to a grounded power outlet by using one of the power cables
included with the display.
Installation and setup
3. For a list of compatible display controllers, please refer to the compatibility matrix available on my.barco.com (MyBarco > My Support
> Healthcare > Compatibility Matrices > Barco Systems Compatibility Matrices)

R5915130 /05 Nio 2MP / 3MP LED Display16
DP IN 1 DP IN 2
DP OUT
USB
DOWN
USB
UP 1
USB
UP 2 DC IN
WORK-
STATION 1
WORK-
STATION 2
KVM 1
KVM 2
SERVICE
Image 2–5
Power on the display system
1. Press/Turn the jog dial to activate your display.
2. Switch on the workstations connected to your display.
Your display will be running in a basic video mode at a default refresh rate when first time starting up.
Install the MXRT driver and Intuitive Workflow Tools
When using a Barco MXRT display controller, install the MXRT driver and Intuitive Workflow Tools on the
connected workstation. Barco’s Intuitive Workflow Tools are designed to increase visibility of subtle details,
improve focus during reading sessions, and accelerate workflow.
1. Download the latest MXRT driver and Intuitive Workflow Tools from www.barco.com/mxrt.
2. Install the MXRT driver and Intuitive Workflow Tools as described in the Barco “Display Controller and
Intuitive Workflow Tools” user guide on the included documentation CD, or at www.barco.com/support.
Enable the KVM switch
1. Bring up the OSD main menu.
2. Navigate to the Image Settings menu.
3. Enter the KVM Switch submenu.
4. Select Enabled and confirm.
When enabling the KVM switch, the Image Source menu will be inaccessible.
To switch KVM inputs
1. Press or turn the jog dial to activate the shortcut bar. The KVM switch icon ( ) is now selected by
default because the KVM switch is enabled.
2. Press the jog dial again to switch KVM inputs.
Installation and setup

17R5915130 /05 Nio 2MP / 3MP LED Display
During normal operation, double-press the jog dial to switch KVM inputs more quickly. A first click
will make the shortcut bar pop up, a second click will switch inputs (since the KVM switch icon is
selected by default when the KVM switch is enabled).
When switching KVM inputs, the video is switched instantly while switching the USB signal might
take a little longer (up to 2 seconds).
2.4 QAWeb Enterprise registration
About
QAWeb Enterprise helps you manage quality and assure compliance of your expanding healthcare
enterprise with less effort, lower cost, and complete confidence. This fully automated and secure system
supports a consistent image quality and uptime for all registered imaging display systems within your facility
and across your enterprise. Learn more at www.barco.com/qaweb.
To register your display system to your QAWeb Enterprise organization, the QAWeb Enterprise Agent must be
installed and running on your workstation and it must be able to communicate with the QAWeb Enterprise
cloud service.
For more information and installation instructions, please check the QAWeb Enterprise user guide on www.
barco.com/support.
2.5 VESA-mount installation
CAUTION: Use suitable mounting apparatus to avoid risk of injury.
WARNING: Never move a display attached to an arm by pulling or pushing the display itself.
Instead, make sure that the arm is equipped with a VESA compliant handle and use this to move the
display.
Please refer to the instruction manual of the arm for more information and instructions.
WARNING: Use a mount that is compliant with the VESA 100 mm standard.
Use a mount that can support the weight of the display. Refer to the technical specifications of this
display for the applicable weight.
Overview
The panel, standard attached to a stand, is compatible with the VESA 100 mm standard. Thus, it can be used
with a mount that is compliant to the VESA 100 mm standard. This chapter shows you how to release the
panel from the stand and how to attach it to a VESA mount. If you’re not using a mount, you can skip this
chapter.
1. Unlock the stand locking mechanism and put the display in the highest position.
Installation and setup

R5915130 /05 Nio 2MP / 3MP LED Display18
Image 2–6
2. Put the display face down on a clean and soft horizontal surface. Be careful not to damage the panel
screen.
3. Push a flathead screwdriver into the right VESA mount cover hole to unlock the cover, then lift the cover
with the flathead screwdriver.
Image 2–7
4. Push a flathead screwdriver into the left VESA mount cover hole to unlock the cover, then lift the cover with
the flathead screwdriver.
Image 2–8
5. Rotate the VESA mount cover to uncover the screws fixing the panel to the stand.
Installation and setup

19R5915130 /05 Nio 2MP / 3MP LED Display
Image 2–9
6. Unscrew the 4 fixation screws while supporting the stand.
Image 2–10
7. Attach the panel firmly to the VESA mount using 4 M4 screws.
Respect the following rule to select an appropriate screw length:
• Lmin = T + W + 10mm
• Lmax = T + W + 12 mm
T
W
Lmin
Lmax
Image 2–11
Installation and setup

R5915130 /05 Nio 2MP / 3MP LED Display20
Installation and setup