Barco Solaris LC40 User manual

MEDIA &EVENTS
SOLARIS LC40
R9004120 (Events)
R9004125 (Media)
OWNERS MANUAL
01042004 R5976672/03

Barco nv Media
Noordlaan 5, B-8520 Kuurne
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Visit us at the web: www.barco.com
Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium

Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.

Table of contents
TABLE OF CONTENTS
1. Safety Instructions.................................................................................................. 3
1.1 General instructions . . . ................................................................................................................ 3
1.2 Electrical Safety ....................................................................................................................... 3
1.3 Protection on Servicing ............................................................................................................... 4
1.4 Safety on Cleaning.................................................................................................................... 5
1.5 Safety on Shipping .................................................................................................................... 5
1.6 On installation site..................................................................................................................... 5
2. Packaging and Dimensions ....................................................................................... 7
2.1 Box content............................................................................................................................ 7
2.2 Packaging ............................................................................................................................. 7
2.3 Dimensions............................................................................................................................ 8
3. Installation Guidelines.............................................................................................11
3.1 General . .............................................................................................................................. 11
3.2 Solaris LC40 configurations.......................................................................................................... 11
3.3 Battery Insertion in the Remote Control............................................................................................. 12
4. Connections.........................................................................................................13
4.1 Power connection . ...................................................................................................................13
4.2 Input source connections . ...........................................................................................................13
4.2.1 Input facilities . . . ...............................................................................................................13
4.2.2 Digital Visual Interface (DVI) input ............................................................................................14
4.2.3 RGB analog input . . . ...........................................................................................................16
4.2.4 Serial Digital Interface.........................................................................................................17
4.2.5 Compact PC module . . . . . . ....................................................................................................17
4.2.6 Video input module . ...........................................................................................................18
4.2.7 DVI input module (optional) . . . ................................................................................................20
4.2.8 HD-SDI input module (optional) . . . ............................................................................................21
4.2.9 RGB input module (optional) . . ................................................................................................22
4.2.10 Audio pré-amp input (optional) ................................................................................................23
4.3 RGB out at native screen resolution (WXGA).......................................................................................24
4.4 Communication Connections . . . . ....................................................................................................25
4.4.1 RS232 IN/OUT................................................................................................................. 25
4.4.2 LAN connection . ...............................................................................................................25
4.5 Cable cover...........................................................................................................................26
5. Getting Started......................................................................................................29
5.1 Terminology overview RCU..........................................................................................................29
5.2 Switching ON/OFF ...................................................................................................................30
5.3 Using the RCU .......................................................................................................................31
5.4 LCD panel address...................................................................................................................32
5.4.1 IR address . . ...................................................................................................................32
5.4.2 Displaying and Programming IR addresses into the RCU . ..................................................................32
5.4.3 RS232 address ................................................................................................................ 32
5.4.4 Controlling the Solaris LC40 with the RCU ...................................................................................32
5.5 Locking the Solaris LC40 for IR signals .............................................................................................34
5.6 Quick access to Picture in Picture...................................................................................................34
6. Getting used to the Menu Structure ............................................................................37
6.1 How to start up the menus...........................................................................................................37
6.2 Using the menus .....................................................................................................................37
6.3 Adjusting a control in a Slider box ..................................................................................................38
7. Input Selection......................................................................................................39
7.1 Start up the Input Selection..........................................................................................................39
7.2 Selecting an Input Source ...........................................................................................................40
7.3 Configuring input 2 ...................................................................................................................40
7.4 Selecting Compact PC...............................................................................................................40
8. Image Settings......................................................................................................43
8.1 Image Settings Menu overview...................................................................................................... 43
8.2 Aspect Ratio..........................................................................................................................43
8.3 Brightness ............................................................................................................................44
8.4 Contrast...............................................................................................................................45
8.5 Color Saturation......................................................................................................................45
8.6 Tint (hue) . . . ..........................................................................................................................46
8.7 Sharpness . . ..........................................................................................................................46
8.8 Viewport ..............................................................................................................................47
8.8.1 About Viewport. . ...............................................................................................................47
8.8.2 Viewport creation ..............................................................................................................48
8.8.3 Automatic Viewport function...................................................................................................51
8.8.4 Total pixels setup ..............................................................................................................52
R5976672 SOLARIS LC40 01042004 1

Table of contents
8.9 Phase.................................................................................................................................53
9. Audio Settings ......................................................................................................55
9.1 Audio settings menu overview.......................................................................................................55
9.2 Starting up the audio controls........................................................................................................55
9.3 Volume control .......................................................................................................................56
9.4 Balance control.......................................................................................................................56
9.5 Bass control ..........................................................................................................................56
9.6 Treble control.........................................................................................................................57
9.7 Subwoofer control....................................................................................................................57
10.PiP Settings .........................................................................................................59
10.1 Introduction to PiP. ...................................................................................................................59
10.2 Select PiP input . . . ...................................................................................................................59
10.3 PiP size...............................................................................................................................60
10.3.1 Scale...........................................................................................................................60
10.3.2 Horizontal size.................................................................................................................61
10.3.3 Vertical size....................................................................................................................61
10.4 PiP position...........................................................................................................................62
11.Compact PC Control...............................................................................................65
11.1 Display control by Compact PC......................................................................................................65
12.Advanced Settings.................................................................................................67
12.1 Advanced Settings menu overview.................................................................................................. 67
12.2 Gamma ............................................................................................................................... 67
12.3 Color Temperature ...................................................................................................................68
12.4 Input Balance . . . . . ....................................................................................................................69
12.4.1 Introduction to Input Balance . . ................................................................................................69
12.4.2 Adjusting the input balance ................................................................................................... 71
12.5 Noise Reduction......................................................................................................................72
12.6 Film mode detection..................................................................................................................73
12.7 Video Gain............................................................................................................................74
12.8 Display Settings ......................................................................................................................75
12.8.1 Rotate..........................................................................................................................75
12.8.2 Backlight .......................................................................................................................76
12.9 Installation............................................................................................................................76
12.9.1 File Services...................................................................................................................76
12.9.1.1 Introduction to image files . . ............................................................................................76
12.9.1.2 Load file set up..........................................................................................................77
12.9.1.3 Loading a specific file...................................................................................................77
12.9.2 When no Signal. ...............................................................................................................78
12.9.3 Language Selection ...........................................................................................................79
12.9.4 Tiled setup .....................................................................................................................79
12.10Service................................................................................................................................81
12.10.1Identification screen ...........................................................................................................81
12.10.2IR address . . ...................................................................................................................82
12.10.3Serial communication..........................................................................................................82
12.10.3.1 RS232 address. . . . . . ....................................................................................................83
12.10.3.2Changing the baudrate for RS232 communication . . ..................................................................83
12.10.4IR locking ......................................................................................................................84
12.10.4.1Locking the display......................................................................................................84
12.10.4.2Changing your PIN code................................................................................................84
12.10.5Restore Factory Defaults......................................................................................................85
A. Standard Source Set up Files ....................................................................................87
A.1 Table overview .......................................................................................................................87
B. Optional Mounting Equipment ...................................................................................89
B.1 Wall Mounting Support ...............................................................................................................89
B.1.1 Kit content...................................................................................................................... 89
B.1.2 Horizontal Wall Mounting Support ............................................................................................89
B.1.3 Vertical Wall Mounting Support . . . ............................................................................................91
B.2 Table mounting support . . . ...........................................................................................................93
C. Specifications .......................................................................................................95
C.1 Specifications Solaris LC40..........................................................................................................95
Glossary .................................................................................................................97
Index......................................................................................................................99
2R5976672 SOLARIS LC40 01042004

1. Safety Instructions
1. SAFETY INSTRUCTIONS
1.1 General instructions
Scope
This document includes safety considerations of the Solaris LC40. Throughout this manual, the term SERVICE PERSONNEL refers
to persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they
are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS
PROJECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. The term
USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate the installed digital
video distribution system.
General safety instructions
• Before operating your Solaris LC40, please read this manual thoroughly, and retain it for future use.
• Installation and preliminary adjustments should be performed by qualified service personnel or authorized service dealers.
• All warnings on the system parts and in the documentation manual should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.
Owner’s Record
The part number and serial number are indicated on the registration plate which is located at the rear of the Solaris LC40.
Record this number here. Refer to that whenever you call upon your dealer regarding these products.
Name Parts Number Serial Number Dealer
Solaris LC40
Shock Hazard
The lightning flash with an arrowhead within a triangle is intended to tell the user that
parts inside this product are risk of electrical shock to persons.
The exclamation point within a triangle is intended to tell the user that important
operating and/or servicing instructions are included in the technical documentation f
o
this equipment.
Image 1-1
1.2 Electrical Safety
Ratings & Grounding
• These products should be operated from an AC power source. Check if the mains voltage and the load matches the product
electrical ratings.
• A grounded three-core power cable has to be used. Connect the power cord by inserting it in a grounded electrical outlet,
making sure that the cord is properly grounded.
• If you are unable to install the AC Requirements, contact your electrician. Do not defeat the purpose of the grounding.
• Always connect this appliance to an electrically grounded outlet. Never use a ground bypass (cheater) adapter.
R5976672 SOLARIS LC40 01042004 3

1. Safety Instructions
General
• Always plug power cord into appliance before plugging into outlet.
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.
• Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Never yank cord to pull plug
from outlet. Grasp plug and pull to disconnect.
• Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged - until it has been examined
by a qualified serviceman.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cord rated
for less amperage than the appliance may overheat.
• Let appliance cool completely before storing. Remove cord from appliance when storing.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set andhaveit
checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet. This will prevent damage to the projector due to lightning and AC power-line
surges.
1.3 Protection on Servicing
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the Unit and cancellation of the warranty
Servicing
Do not attempt to service the installed modules yourself, as opening or removing covers may expose you to dangerous voltage
potential and risk of electric shock! Refer all projector service to a qualified service center.
Call for service in the following conditions :
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the modules.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation;
• If the product has been dropped or the cabinet has been damaged;
• If the product exhibits a distinct change in performance, indicating a needforservice.
Replacement Parts
When replacement parts are required, be sure the service technician has used original BARCO replacement parts or authorized
replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions may result in de-
graded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
Safety Check
Upon completion of any service or repairs to these modules, ask the service technician to perform safety checks to determine that
the modules are in proper operating condition.
Protection
Please do not disassemble or modify LCD module to avoid the possibility of electric shock, damage of electronic components, scratch
at display surface and invasion of foreign particles. In addition, such activity may result in fire accident due to burning of electronic
component. LCD module disassembled or modified by customer is out of warranty.
Please be careful in handling of display with broken glass. When the display glass breaks, please pay attention not to injure your
fingers. The display surface has the plastic film attached, which prevents dispersion of glass pieces, however touching broken edge
will injure your fingers. Also Lamp (Cold Cathode Fluorescent Lamp) is made of glass, therefore please pay attention in the same
way.
Please do not touch the fluid flown out of broken display glass. If the fluid should stick to hand or clothes, wipe off with soap or
alcohol immediately and then wash it with water. If the fluid should get in eyes, wash eyes immediately with pure water for more
than 15 minutes and then consult the doctor.
Lamp contains mercury inside. Please follow regulations or rules established by local autonomy at its disposal.
4R5976672 SOLARIS LC40 01042004

1. Safety Instructions
1.4 Safety on Cleaning
Cabinet
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these
will damage the cabinet.
Display surface
Contamination of display surface. When display surface of LCD module is contaminated, please wipe the surface softly with
cotton swab or clean cloth. If it is not enough, please take it away with cellophane tape or wipe the surface with cotton swab or clean
cloth containing benzine. In this case, please be careful so that benzine does not get in inside of LCD module, because it may be
damaged.
Water drop on LCD surface. Please do not leave LCD module with water drop. When the display surface gets water drop, please
wipe it off with cotton swab or soft cloth immediately, otherwise display surface will be deteriorated. If water gets in inside of LCD
module, circuit may be damaged.
1.5 Safety on Shipping
Original Shipping package
Save the original shipping packing material; they will come in handy if you ever have to ship one of your installed modules. For
maximum protection, repack your set as it was originally packed at the factory.
1.6 On installation site
Transportation
• Any transportation of the unopened unit in its packaging should be done by two persons.
• In transportation or storage of products in original packing, NEVER stack more than the number stated on the carton box. This
warning is also indicated on the side of the carton.
• For transportation or storage, observe the warnings and instructions on the side of the carton.
Nearby equipment
If air conditioning ducts or lamps, etc. are located near the installation site, the attendant dust, extreme temperatures, humidity, and
condensation may become sources of trouble. Please take sufficient steps to avoid this.
Safety locations
Do not install the unit where it may be easily touched or leaned against. Avoid locations subject to high vibrations or severe impacts.
Mechanical stress. Please be careful not to apply strong mechanical stress like drop or shock to LCD module. Such stress may
cause break of display glass and Lamp or may be the cause for failure.
Pressure to display surface. Please be careful not to apply strong pressure to display surface. Such pressure may cause scratches
at surface or may be the cause of failure.
Protection against scratch. Please be careful not to hit, press or rub the display surface with hard material like tools. In addition,
please do not put heavy or hard material on display surface, and do not stack LCD modules. Polarizer at front surface can be easily
scratched.
Temperature dependence of display. Response speed (optical response) of LCD display is dependent on temperature. Under
low temperature, response speed is slower. Also brightness and chromaticity change slightly depending on temperature.
Remaining of image
Displaying the same pattern for long time may cause remaining of image even after changing the pattern. This is not a failure but
will disappear with time.
Lightning conditions
• Consider existing lightning and sunlight angles when creating the installation layout. Extremely bright lightning can reduce the
visibility and the quality of the displayed image.
• In extremely bright surroundings, adjusting screen intensity may not result in perceptibly brightener images. Keep in mind that
extreme intensity settings can reduce system service life.
R5976672 SOLARIS LC40 01042004 5

1. Safety Instructions
Installation partially outdoors
The unit is designed for indoor use, and is not suited for open-air use. Installation in locations that are even partially exposed to the
elements may lead to malfunctions or breakdown caused by any of the following:
• Water and dust
• Changes in temperature and humidity
• Salt-bearing wind
6R5976672 SOLARIS LC40 01042004

2. Packaging and Dimensions
2. PACKAGING AND DIMENSIONS
Overview
• Box content
• Packaging
• Dimensions
2.1 Box content
Content
Standard delivered for :
R9004120 R9004125
• 1 Solaris LC40 (weight : 24.5 kg)
• 2 power cables with outlet plug type CEE7 and ANSI
73.11
• 1 owners manual
• 1 remote control
• 1 video input
• 1 Solaris LC40 (weight : 24.5 kg)
• 2 power cables with outlet plug type CEE7 and ANSI
73.11
• 1 owners manual
CEE7
European power plug to connect the power cord to the wall outlet.
ANSI 73.11
American power plug to connect the power cord to the wall outlet.
2.2 Packaging
Way of Packaging
The Solaris LC40 is packed in a carton box. To provide protection during transportation, the Solaris LC40 is surrounded with foam.
The packaging is secured with banding and fastening clips.
To unpack
1. Release the fastening clips.
2. Remove the banding.
3. Take the Solaris LC40 out of its shipping carton.
Save the original shipping carton and packing material, they will be necessary if you ever have to ship your
panel. For maximum protection, repack your panel as it was originally packed at the factory.
R5976672 SOLARIS LC40 01042004 7

2. Packaging and Dimensions
2.3 Dimensions
Front view
863
950
452.5
518.25
610
Image 2-1
Front view
Back view
950
234
100
610
Image 2-2
Back view
8R5976672 SOLARIS LC40 01042004

2. Packaging and Dimensions
Bottom view
107
Image 2-3
Bottom view
R5976672 SOLARIS LC40 01042004 9

2. Packaging and Dimensions
10 R5976672 SOLARIS LC40 01042004

3. Installation Guidelines
3. INSTALLATION GUIDELINES
Overview
• General
• Solaris LC40 configurations
• Battery Insertion in the Remote Control
3.1 General
Environmental conditions
• Operating temperature : 5° to 40°C (41° to 104°F)
• Humidity : max 85%
3.2 Solaris LC40 configurations
Different configurations
The Solaris LC40 can be used in two different configurations, landscape and portrait.
The portrait configuration is only possible with the optional Rotator module (order number : R9842362)
Image 3-1
Landscape configuration
Image 3-2
Portrait configuration
When using in landscape, the infra red receiver must be in the lower left corner.
When using in portrait, the infra red receiver must be in the upper left corner.
Applications
The Solaris LC40 can be used as stand alone display or as part of a network of displays.
R5976672 SOLARIS LC40 01042004 11

3. Installation Guidelines
3.3 Battery Insertion in the Remote Control
Where to find the batteries
The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
time.
How to install the batteries
1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 3-3)
2. Slide the cover forwards to remove. (image 3-4)
3. Push the battery body towards the spring and lift it up to remove. (image 3-5)
4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 3-5).
5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
(image 3-4).
Image 3-3
Battery cover unlock
Image 3-4
Battery cover removal
Image 3-5
Battery removal
12 R5976672 SOLARIS LC40 01042004

4. Connections
4. CONNECTIONS
Overview
• Power connection
• Input source connections
• RGB out at native screen resolution (WXGA)
• Communication Connections
• Cable cover
4.1 Power connection
AC power (mains) cord connection
Use the supplied power cord to connect your LCD panel to the wall outlet.
Plug the female power connector into the male connector at the back of the LCD panel.
The power input is auto-ranging from 90 to 240 VAC.
4.2 Input source connections
Overview
• Input facilities
• Digital Visual Interface (DVI) input
• RGB analog input
• Serial Digital Interface
• Compact PC module
• Video input module
• DVI input module (optional)
• HD-SDI input module (optional)
• RGB input module (optional)
• Audio pré-amp input (optional)
4.2.1 Input facilities
Input panel view
DVI
RGB out (1280x768)
RGB HV
RS232
OUT IN
LAN RGB analog
RGBHVINOUT
SDI
ABCD E
Image 4-1
Input panel view
Overview standard available inputs
Ref Input connector Source
ADVI DVI digital
DVI analog
R5976672 SOLARIS LC40 01042004 13

4. Connections
Ref Input connector Source
BRGB analog (BNC) RGB
CSDI SDI
Overview optional inputs
Ref Input slot Input module Source
DUniversal input for data sources DVI input DVI digital
DVI analog
RGB input RGB
HD-SDI input HD-SDI
Audio input Audioin(L+R),audioout(L+R+
Subwoofer)
EVideo sources Video input Video
S-Video
Component video
RGB Video (15 kHz)
4.2.2 Digital Visual Interface (DVI) input
DVI
Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays.
The digital video connectivity standard that was developed by DDWG (Digital Display Work Group). This connection
standard offers two different connectors: one with 24 pins that handles digital video signals only, and one with 29 pins
that handles both digital and analog video. This standard uses TMDS (Transition Minimized Differential Signal) from
Silicon Image and DDC (Display Data Channel) from VESA (Video Electronics Standards Association).
DVI can be single or dual link.
Input specifications
DVI
RGB out (1280x768)
RGBHV
RS232
OUT IN
LAN RGB analog
RGBHVINOUT
SDI
DVI
x768)
HV RG
Image 4-2
Standard DVI input
Pixel clock : 25 .. 165 MHz
Horizontal sync range : 15 .. 110 kHz
Vertical sync range : 23 .. 125 Hz
Max. input format : UXGA (1600x1200) @ 60 Hz
14 R5976672 SOLARIS LC40 01042004

4. Connections
DVI-Digital
• Single link
• Differential input voltage : 200mV - 800mV
DVI-Analog
• RGB input = 0.7 Vpp ±3dB
• TTL sync input : Umin =2.5V
Pin assignment for the DVI connector.
Pin 1 TMDS DATA2- Pin 15 Ground (for +5V)
Pin 2 TMDS DATA2+ Pin 16 Hot Plug Detect
Pin 3 TMDS DATA2/4 Shield Pin 17 TMDS DATA0-
Pin 4 TMDS DATA4- Pin 18 TMDS DATA0+
Pin 5 TMDS DATA4+ Pin 19 TMDS DATA0/5 Shield
Pin 6 DDC Clock Pin 20 TMDS DATA5-
Pin 7 DDC Data Pin 21 TMDS DATA5+
Pin 8 Analog Vert sync Pin 22 TMDS Clock Shield
Pin 9 TMDS DATA1- Pin 23 TMDS Clock+
Pin 10 TMDS DATA1+ Pin 24 TMDS Clock-
Pin 11 TMDS DATA1/3 Shield C1 Analog Red
Pin 12 TMDS DATA3- C2 Analog Green
Pin 13 TMDS DATA3+ C3 Analog Blue
Pin14 +5Power C4 Analog Hor Sync
C5 Ground
How to select the DVI input via the RCU?
1. Press 7on the RCU.
The internal system detects automatically the DVI source. If at the same time a digital DVI and analog DVI source is connected
and switched on, the digital DVI source will be displayed.
How to select the DVI input via the menu structure?
1. Press on the thumb wheel or press ENTER on the RCU to activate the menus.
The main menu will be displayed on the screen. (menu 4-1)
2. Turn the thumb wheel or use the up or down arrow keys to select Input selection.
The input selection menu will be displayed. (menu 4-2)
3. Turn the thumb wheel or use the up or down arrow keys to select 7DVI.
4. Press the thumb wheel or press ENTER on the RCU.
The internal system detects automatically the DVI source. If at the same time a digital DVI and analog DVI source is connected
and switched on, the digital DVI source will be displayed.
Solaris LC40
Select input
Image settings
Audio settings
PiP settings
Compact PC Control
Advanced settings
Standby
Back
Menu 4-1
Select input
1. Video
2. RGB
3. S-Video
4. HD-SDI/DVI/Audio/RGB
5. SDI
6. RGB
7. DVI
8. Compact PC
Configure input 2
Back
Menu 4-2
R5976672 SOLARIS LC40 01042004 15

4. Connections
4.2.3 RGB analog input
Input specifications
DVI
RGB out (1280x768)
RGBHV
RS232
OUT IN
LAN RGB analog
RGBHVINOUT
SDI
RGB analog
RGB HVINOUT
SDI
Image 4-3
RGB analog input
Pixel clock : 20 .. 165 MHz
Horizontal sync range : 15 .. 110 kHz
Vertical sync range : 23 Hz .. 125 Hz
Max input format : UXGA (1600x1200) @ 60 Hz
RGBHV inputs : 0.7Vpp ±3 dB
Possible input sources
Inputs
RGB H V
RGBHV RGB H V
RGBS RGBS-
RGB inputs
RGsBRGsB- -
How to select the RGB source via the RCU?
1. Press 6on the RCU.
The system scans the RGB analog input for a RGB input signal and detects automatically the sync.
How to select the RGB source via the menu structure
1. Press on the thumb wheel or press ENTER on the RCU to activate the menus.
The main menu will be displayed on the screen. (menu 4-3)
2. Turn the thumb wheel or use the up or down arrow keys to select Input selection.
The input selection menu will be displayed. (menu 4-4)
3. Turn the thumb wheel or use the up or down arrow keys to select 6RGB.
4. Press the thumb wheel or press ENTER on the RCU.
The internal system detects automatically the sync position (separate sync or sync on green).
Solaris LC40
Select input
Image settings
Audio settings
PiP settings
Compact PC Control
Advanced settings
Standby
Back
Menu 4-3
Select input
1. Video
2. RGB
3. S-Video
4. HD-SDI/DVI/Audio/RGB
5. SDI
6. RGB
7. DVI
8. Compact PC
Configure input 2
Back
Menu 4-4
16 R5976672 SOLARIS LC40 01042004