Barco FS-FL40 MKII Series User manual

ENABLING BRIGHT OUTCOMES
User Manual
FS-FL40 MKII series

Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com

Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be
recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Changes
Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make
improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made
to the information in this publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the
secured Barco web site https://www.barco.com/en/signin.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights
of their respective holders. All brand and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or their manufacturers.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area may cause harmful interference, in which case the user will be responsible for correcting any interference
at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment
FCC responsible: Barco Inc.
3059 Premiere Parkway Suite 400
30097 Duluth GA, United States
Tel: [phone]
Patent protection
Please refer to www.barco.com/about-barco/legal/patents
Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
[Republic of Turkey: In conformity with the WEEE Regulation]
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste
from electrical and electronic equipment, this product must not be disposed of with other municipal waste.
Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. To prevent possible harm to the environment or human health from

uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal
waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/AboutBarco/weee
Software License Agreement
You should carefully read the following terms and conditions before using this software. Your use of this
software indicates your acceptance of this license agreement and warranty.
Terms and Conditions:
1. No redistribution of the software is allowed.
2. Reverse-Engineering. You may not reverse engineer, decompile, disassemble or alter this software
product.
Disclaimer of Warranty:
This software and the accompanying files are sold “as is”and without warranties as to performance or
merchantability or any other warranties whether expressed or implied. In no event shall Barco be liable for
damage of any kind, loss of data, loss of profits, business interruption or other pecuniary loss arising directly or
indirectly. Any liability of the seller will be exclusively limited to replacement of the product or refund of
purchase price.
Patent protection
Please refer to www.barco.com/about-barco/legal/patents
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and
disposed of separately from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these
chemical symbols will appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent
potential negative effects on the environment and human health.
EMC notices
EN55032/CISPR32 Class A MME (MultiMedia Equipment)
Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment
may cause radio interference.
GB/T 9254 Class A ITE (Information Technology Equipment)
Warning : This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
BSMI Taiwan Class A statement:
警告使用者 :此為甲類資訊技術設備，於居住環境中使用 ，可能會造成射頻擾動，在此情況下，使用者會被要
求採取某些適當的對策。
Disclaimer on GUI images used in this manual
The GUI images in this manual are example illustrations and should be treated as such. While the name of the
projector displayed in the illustrations may be different from the projector model you are currently using, the
menu lay-out and functionality is identical.

5R5913251 /00 FS-FL40 MKII series
1 Safety and environmental information ................................................................................................................................. 7
1.1 General considerations ..................................................................................................................................................................8
1.2 Important safety instructions........................................................................................................................................................8
1.3 Safety Symbols FL40 / FS40.................................................................................................................................................... 11
1.4 Location of labels ............................................................................................................................................................................ 12
1.5 Disposal Information .....................................................................................................................................................................12
1.6 Turkey RoHS compliance...........................................................................................................................................................12
1.7 China RoHS compliance.............................................................................................................................................................13
1.8 Taiwan RoHS compliance..........................................................................................................................................................14
1.9 Contact information........................................................................................................................................................................15
1.10 Production Address .......................................................................................................................................................................15
1.11 Product Info........................................................................................................................................................................................15
1.12 Statement............................................................................................................................................................................................15
2 Important notice ......................................................................................................................................................................................17
2.1 Grinding sound during startup.................................................................................................................................................18
3 Getting to know the projector.....................................................................................................................................................19
3.1 Location of the main exterior components. ......................................................................................................................20
3.2 Service and maintenance...........................................................................................................................................................21
3.3 Power on / Standby button backlight indications...........................................................................................................21
3.4 LCD Panel...........................................................................................................................................................................................21
3.4.1 LCD panel general .....................................................................................................................................................21
3.4.2 LCD touch panel..........................................................................................................................................................22
3.4.3 LCD Status screens...................................................................................................................................................22
3.4.4 OSD Menu mode.........................................................................................................................................................24
3.4.5 LCD functionality in Ready Mode.......................................................................................................................24
3.5 Local keypad .....................................................................................................................................................................................25
3.6 Remote control.................................................................................................................................................................................26
3.6.1 Remote control, battery installation ..................................................................................................................26
3.6.2 Remote control, protocol setup ...........................................................................................................................27
3.6.3 Functionality overview..............................................................................................................................................28
3.6.4 Remote control, on/off button...............................................................................................................................28
3.6.5 Function of the RGB filter button ........................................................................................................................29
3.6.6 Enable / Disable Remote Control.......................................................................................................................29
3.6.7 Wired RC connection................................................................................................................................................30
Table of contents

R5913251 /00 FS-FL40 MKII series6
3.7 Projector Address ...........................................................................................................................................................................30
3.7.1 Controlling the projector ..........................................................................................................................................30
3.8 Connector panel ..............................................................................................................................................................................31
4 Lenses..............................................................................................................................................................................................................33
4.1 Approved lenses..............................................................................................................................................................................34
4.2 Replace a lens..................................................................................................................................................................................34
4.3 Locking the lens position ............................................................................................................................................................36
5 Getting the projector started .......................................................................................................................................................39
5.1 Projector source and control connections.........................................................................................................................40
5.1.1 Input source connections........................................................................................................................................40
5.1.2 Connector Specifications........................................................................................................................................40
5.1.2.1 DVI-I ........................................................................................................................................................40
5.1.2.2 Display Port 1.2.................................................................................................................................40
5.1.2.3 HDMI 2.0...............................................................................................................................................41
5.1.2.4 HDBase T.............................................................................................................................................41
5.1.3 Control Interfaces........................................................................................................................................................42
5.1.3.1 RS-232...................................................................................................................................................42
5.1.3.2 LAN/Ethernet......................................................................................................................................42
5.1.3.3 USB-A port...........................................................................................................................................42
5.2 Power up the projector.................................................................................................................................................................43
5.3 Power down the projector ..........................................................................................................................................................43
5.4 Power mode transitions...............................................................................................................................................................43
5.4.1 General.............................................................................................................................................................................43
5.4.2 Power on projector .....................................................................................................................................................44
5.4.3 Going from READY to ON......................................................................................................................................44
5.4.4 Going from ON to READY......................................................................................................................................44
5.4.5 Going from READY to ECO standby................................................................................................................45
5.4.6 Going from ECO to ON ............................................................................................................................................45
5.4.7 Wake On LAN (WOL) ...............................................................................................................................................45
5.5 Power modes ....................................................................................................................................................................................45
5.6 Customize projector settings....................................................................................................................................................45
5.7 User interface....................................................................................................................................................................................46
5.7.1 On Screen Display (OSD) ......................................................................................................................................46
6 GUI –Profiles ............................................................................................................................................................................................47
6.1 Profiles introduction.......................................................................................................................................................................48
6.2 Profiles setup parameters..........................................................................................................................................................48
6.3 Create new profile ..........................................................................................................................................................................49
7 3D .........................................................................................................................................................................................................................53
7.1 Setup 3D mode................................................................................................................................................................................54
8 Upgrade projector firmware.........................................................................................................................................................57
8.1 Upgrade procedure........................................................................................................................................................................58
9 User maintenance —Cleaning the projector .............................................................................................................59
9.1 Projector lenses...............................................................................................................................................................................60
9.2 Projector cabinet .............................................................................................................................................................................60
9.3 Filters .....................................................................................................................................................................................................60
Index ..................................................................................................................................................................................................................61

7R5913251 /00 FS-FL40 MKII series
About
Read this chapter thoroughly before attempting to install or operate the projector.
To prevent personal injury to users or physical damage to the projector while installing and using your
projector, ensure that you understand and follow all safety guidelines, instructions and warnings included in
this chapter and this manual.
Clarification of the term FL40 series used in this document
Use in this document of the term, FL40 , means that the content is applicable for the following products:
•FL40 - WU
•FL40 - 4K
•FS40 - WU
•FS40 - 4K
Defining the FL40 platform
The FL40 series products in general, are all products within the Barco GP5 platform
Safety and
environmental
information 1

R5913251 /00 FS-FL40 MKII series8
1.1 General considerations
Notice on optical radiation FL40 Series
•Do not stare into Beam.
•This projector is Risk Group 2 (RG2) according to IEC EN 62471-5.
•Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous
light radiation exposure.
•Do not open or disassemble the projector as this may cause danger to unauthorized personnel
General safety instructions
•This product contains no user serviceable parts.
Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any
warranties and may be hazardous.
•Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
•Before operating this equipment please read this manual thoroughly and retain it for future reference.
•Installation and preliminary adjustments should be performed by properly trained and qualified personnel.
•All warnings on the projector and in the documentation manuals must be adhered to.
•All instructions for operating and use of this equipment must be followed precisely.
•All local installation codes should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1,
as basis for National safety regulation world wide. The safety standard covers information technology
equipment including electrical business equipment intended to operate in “normal”environments (offices and
homes). This safety standard imposes important requirements on the use of safety critical components,
materials and insulation, in order to protect the user or operator against risk of electric shock and energy
hazard and having access to live parts. Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection
against the risk of fire. Simulated single fault condition testing reduce the risk of hazards and contribute to
ensure the safety of the equipment to the user even when the equipment’s normal operation fails.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having
appropriate technical training and experience necessary to be knowledgeable of potential hazards to which
they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY
and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk
to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks,
are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers
to any person other than SERVICE PERSONNEL.
1.2 Important safety instructions
To prevent the risk of electrical shock
•This product should be operated from a mono phase AC power source.
•This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the
supplied power cables are the correct one, consult your dealer.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the purpose of the grounding-type plug.
Never use 2- wire power cords, as this is dangerous and could lead to electrical shock. Always use a
power connector with a ground terminal.
•Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the
cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
•Ensure that the main power cord complies with the national regulations at the site where the equipment is
used.
•Do not use unauthorized replacements
Safety and environmental information

9R5913251 /00 FS-FL40 MKII series
•Do not operate the projector with a damaged cord. Replace the cord.
Do not operate the projector if the projector has been dropped or damaged - until it has been examined
and approved for operation by a qualified service technician.
•Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should
be used. A cord rated for less amperage than the projector may overheat.
•Never push objects of any kind into this product through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a risk of fire or electrical shock.
•Make sure that no objects enter into the vents and openings of the set.
•Do not expose this projector to rain or moisture.
•The projector is designed for indoor use only. Never operate the unit outdoors.
•Do not immerse or expose this projector in water or other liquids.
•Do not spill liquid of any kind on this projector.
•Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations.
•Do not disassemble this projector, always take it to an authorized trained service person when service or
repair work is required.
•Do not use an accessory attachment which is not recommended by the manufacturer.
•Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device
due to lightning and AC power-line surges.
To prevent personal injury
•To prevent injury and physical damage, always read this manual and all labels on the system before
connecting to the wall outlet or adjusting the projector.
•To prevent injury, take note of the weight of the projector.
•To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•Warning: high intensity light beam. NEVER look into the lens! High luminance could result in damage to the
eye.
•Always switch off the projector and disconnect from the mains power supply before attempting to remove
any of the projector covers or access parts inside the projector.
•This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics
inside the housing or compartments will violate any warranties and may be hazardous.
•Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it and possible injury to the user.
•Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.
To prevent fire hazard
•Barco projection products are designed and manufactured to meet the most stringent safety regulations.
This projector radiates heat on its external surfaces and from ventilation ducts during normal operation,
which is both normal and safe. Exposing flammable or combustible materials into close proximity of this
projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is
absolutely necessary to leave an “exclusion zone”around all external surfaces of the projector whereby no
flammable or combustible materials are present.
•Do not place flammable or combustible materials near the projector!
•Caution! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than
25 cm (10”) to the exhaust vent.
•Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the
projector and to protect it from overheating, these openings must not be blocked or covered.
•The openings should never be blocked by placing the projector too close to walls, or other similar surface.
Allow for sufficient distance to walls and ceilings to avoid overheating. Minimum safety distance to the
exhaust area of the unit must not be less than 25 cm (10”) and to the intake area, not less than 25 cm (10”).
•This projector should never be placed near or over a radiator or heat register.
•This projector should not be placed in a built-in installation or enclosure unless proper ventilation is
provided.
•Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable
and combustible materials away from the projector at all times.
Safety and environmental information

R5913251 /00 FS-FL40 MKII series10
•Mount the projector in a well-ventilated area away from sources of ignition and out of direct sun light.
Always allow ample airflow through the projector.
•Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder fire
extinguishers.
•Never use water on an electrical fire.
•Always have service performed on this projector by authorized Barco service personnel. Always insist on
genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety
of this projector.
•Projection rooms must be well ventilated or cooled in order to avoid heat buildup.
•Let the projector cool down completely before storing. Remove cord from the projector when storing.
To prevent projector damage
•To ensure correct airflow is maintained, the projector should only be operated when all of its covers in
place. The exception from this is the front cover, that can be removed to give access to multiple anchor
points. See User Guide for more detailed info regarding this issue.
•Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due
to the high energy light emitted through the lens. Melting the lens cap may permanently damage the
surface of the projection lens
•Only connect the projector to signal sources and voltages as described in the technical specification.
Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of
the unit.
•To ensure correct airflow is maintained, it should only be operated when all of its covers are in place.
•The projector must always be installed in a manner which ensures free flow of air into its air inlets and
unimpeded evacuation of the hot air from its cooling system.
•Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register. The device should not be placed in a built-in
installation or enclosure unless proper ventilation is provided. Ensure that nothing can be spilled on, or
dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do
not operate the projector again until it has been checked by Barco authorized service personnel.
•Do not block the projector cooling fans or free air movement around the projector. Minimum safety distance
to the exhaust area of the unit must not be less than 25 cm (10”) and to the intake area, not less than 25
cm (10”).
•Do not use this equipment near water.
•Do not operate the projector outside its temperature and humidity specifications as this may result in
overheating and malfunction.
•Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror
Devices™in which case there is a loss of warranty.
•Save the original shipping carton and packing material. They will come in handy if you ever have to ship
your equipment. For maximum protection, repack your set as it was originally packed at the factory.
•Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive
cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution.
•To ensure the highest optical performance and resolution, the projection lenses are specially treated with
an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry
cloth. Do not use a damp cloth, detergent solution, or thinner.
On servicing
•Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage potentials and risk of electric shock.
•Refer all servicing to Barco authorized repair centers.
•Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
•Unplug this product from the wall outlet and refer servicing to Barco authorized service personnel or
technicians under the following conditions:
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
Safety and environmental information

11R5913251 /00 FS-FL40 MKII series
- If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
- When the power cord or plug is damaged or frayed.
•Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts. Unauthorized substitutions may result in degraded performance and reliability,
fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
•Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
1.3 Safety Symbols FL40 / FS40
Description of safety symbols used in product documentation or on product.
Image Description
Refer to user manual for further
information!
Caution! Do not stare into beam,
RG2 product.
No telephone! Do not connect to
telephone lines.
This is a class A product. In a domestic environment this product
may cause radio Interference in which case the user may be
required to take adequate measures.
This device complies with part 15 of the FCC Rules,Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This Class A digital apparatus complies with Canadian ICES-003,/ Cet appareil numerique
de Ia classe est conforme à Ia norme NMB-003 du Canada.
EMC:
FCC:
CANADA:
此為甲類資訊技術設備，於居住環境中使用時，可 能會造成射頻擾動，
在此種情況下，使 用者會被要求採取某些適當的對策。
警告使用者
RG2 IEC EN 62471-5
FL40 EMC Label
RG2 IEC EN 62471-5
FL40 RG2 Label
Safety and environmental information

R5913251 /00 FS-FL40 MKII series12
1.4 Location of labels
Label positions
This is a class A product. In a domestic environmentthis product
may cause radio Interference in which case the user may be
required to take adequate measures.
This device complies with part 15 of the FCC Rules,Operation is subject to the following
conditions: (1)This device may not cause harmful interference, and (2) this device must
accept any interference received,including interference that may cause undesired operation.
This Class A digital apparatus complies with Canadian ICES-003,/ Cet appareil numerique
de Ia classe est conforme à Ia norme NMB-003 du Canada.
EMC:
FCC:
CANADA:
此為甲類資訊技術設備，於居住環境中使用時，可 能會造成射頻擾動，
在此種情況下，使 用者會被要求採取某些適當的對策。
警告使用者
RG2 IEC EN 62471-5
RG2 IEC EN 62471-5
Image 1–1 Location of RG2 and EMC label.
1.5 Disposal Information
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste
from electrical and electronic equipment, this product must not be disposed of with other municipal waste.
Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of
waste electrical and electronic equipment. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal
waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/AboutBarco/weee
WEEE Information
This product conforms to all requirements of the EU Directive on waste electrical and electronic equipment
(WEEE). This product shall be recycled properly. It can be disassembled to facilitate proper recycling of it’s
individual parts.
Consult your dealer or relevant public authority regarding drop-off points for collection of WEEE. For details,
please visit the Barco website at: http://www.barco.com/en/ AboutBarco/weee.
1.6 Turkey RoHS compliance
Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
Safety and environmental information

13R5913251 /00 FS-FL40 MKII series
[Republic of Turkey: In conformity with the WEEE Regulation]
1.7 China RoHS compliance
中国大陆 RoHS (Information for China ROHS compliance)
根据中国大陆《电器电子产品有害物质限制使用管理办法》（也称为中国大陆RoHS）， 以下部分列出了
Barco产品中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标
准：“电子信息产品中有毒物质的限量要求”中。
According to the “Management Methods for the Restriction of the Use of Hazardous Substances in Electrical
and Electronic Products”(Also called RoHS of Chinese Mainland), the table below lists the names and
contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese
Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit
Requirements of toxic substances in Electronic Information Products”.
零件项目(名称)
Component name
有毒有害物质或元素
Hazardous substances and elements
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯
醚
(PBDE)
印制电路配件
Printed Circuit Assemblies X O X O O O
外接电(线)缆
External Cables X O O O O O
內部线路
Internal wiring X O O O O O
镜头支架
Lensholder X O O O O O
螺帽,螺钉(栓),螺旋(钉),垫圈,紧固
件
Nuts, bolts, screws, washers,
Fasteners
XO O O O O
电源供应器
Power Supply Unit X O O O O O
风扇
Fan X O O O O O
附電池遙控器
Remote control X O O O O O
本表格依据SJ/T 11364的规定编制
This table is prepared in accordance with the provisions of SJ/T 11364.
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572 标准规定的限量要求以下.
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this
part is below the limit requirement in GB/T 26572.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 标准规定的限量要求.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials
used for this part is above the limit requirement in GB/T 26572.
10
在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子电气产品有害物质
限制使用标识要求》标准贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP标签
（请参阅实例，徽标内部的编号使用于指定产品）基于中国大陆的《电子信息产品环保使用
期限通则》标准。
Safety and environmental information

R5913251 /00 FS-FL40 MKII series14
All Electronic Information Products (EIP) that are sold within Chinese Mainland must
comply with the “Marking for the restriction of the use of hazardous substances in electrical
and electronic product”of Chinese Mainland, marked with the Environmental Friendly Use
Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the
photo) is based on the “General guidelines of environment-friendly use period of electronic
information products”of Chinese Mainland.
1.8 Taiwan RoHS compliance
限用物質含有情況標示聲明書 (Declaration of the Presence Condition of the Restricted
Substances Marking)
限用物質及其化學符號
Restricted substances and its chemical symbols
單元
Unit
鉛
Lead
(Pb)
汞
Mercu-
ry
(Hg)
鎘
Cadmi-
um
(Cd)
六價鉻
Hexava-
lent
chromi-
um
(Cr6+)
多溴聯苯
Polybromi-
nated
biphenyls
(PBB)
多溴二苯醚
Polybromi-
nated
diphenyl
ethers
(PBDE)
印製電路板配件
Printed Circuit Assemblies —O—O O O
外接電（線）纜
External Cables —O O O O O
內部線路
Internal wiring —O O O O O
鏡頭支架
Lensholder —O O O O O
螺絲組件
Nuts, bolts, screws, washers,
Fasteners
—O O O O O
電源供應器
Power Supply Unit —O O O O O
風扇
Fan —O O O O O
遙控器
Remote control —O O O O O
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。
Note 1：“Exceeding 0.1 wt %”and “exceeding 0.01 wt %”indicate that the percentage content of the
restricted substance exceeds the reference percentage value of presence condition.
備考2.〝〇〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2：“〇” indicates that the percentage content of the restricted substance does not exceed the
percentage of reference value of presence.
備考3.〝—〞係指該項限用物質為排除項目。
Note 3：The “—” indicates that the restricted substance corresponds to the exemption.
備註:此RoHS表格適用於以下產品型號: GP5
Hint: This RoHS table is suitable for following models: GP5
Safety and environmental information

15R5913251 /00 FS-FL40 MKII series
1.9 Contact information
Barco contact information
Registered office address: President Kennedypark 35, 8500 Kortrijk, Belgium
Contact address: Beneluxpark 21, 8500 Kortrijk, Belgium
Contact address (for Taiwan) :
公司名稱 (Company Name)：巴可股份有限公司
地址 (Address)：新北市板橋區新站路16號33樓
傳真 (Fax)：02-7715 0298
電話 (Tel)：02-7715 0299
E-mail：[email protected]
Importers contact information
To find your local importer, contact Barco directly or one of Barco's regional offices via the contact information
given on Barco's web site, www.barco.com.
Contact information Norway factory
Barco Fredrikstad as
Habornveien 53, N1630 Gamle Fredrikstad, Norway
Phone: [phone]
Support:[email protected]
1.10 Production Address
Factories
Barco NV (BELGIUM)
President Kennedypark 35 , B-8500 Kortrijk
1.11 Product Info
Product info
Image 1–2
product name 產品名稱:
projector 投影機
model 型號: GP5
1.12 Statement
EN55032/CISPR32 Class A MME (MultiMedia Equipment)
Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment
may cause radio interference.
Safety and environmental information

R5913251 /00 FS-FL40 MKII series16
Class A ITE (Information Technology Equipment)
Warning : This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
警告使用者:此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會
被要求採取某些適當的對策。
Safety and environmental information

17R5913251 /00 FS-FL40 MKII series
Important notice 2

R5913251 /00 FS-FL40 MKII series18
2.1 Grinding sound during startup.
About
Note that a grinding sound can be heard at startup from ready-state to power ON every time the power has
been disconnected.
This sound will appear every time the dimming disk needs to be calibrated during start up.
Mechanical sound from the dimming disk can also be heard every time you adjust the LED power below 50%
output.
Important notice

19R5913251 /00 FS-FL40 MKII series
3.1 Location of the main exterior components.......................................................................................20
3.2 Service and maintenance..............................................................................................................21
3.3 Power on / Standby button backlight indications ..............................................................................21
3.4 LCD Panel ...................................................................................................................................21
3.5 Local keypad................................................................................................................................25
3.6 Remote control.............................................................................................................................26
3.7 Projector Address .........................................................................................................................30
3.8 Connector panel...........................................................................................................................31
Getting to know the
projector. 3

R5913251 /00 FS-FL40 MKII series20
3.1 Location of the main exterior components.
Defining of surfaces
Front
Right
Left
Back
Top
Bottom
Image 3–1
Main Components
4
1
7
8
5
2
6
3
5
5
Image 3–2
Main exterior components matrix
Item Number Component Item Number Component
1 IR Receiver top 5 Projector feet (x4)
2 IR Receiver front 6 LCD Panel
3 Lens 7 Key Pad
4 Lens release handle 8 Back Panel / Connectors
Getting to know the projector.