Barco RLS W12 User manual

RLS W12
MSWU-81E

Document version: 00
Barco NV Projection Division
Noordlaan 5, B-8520 Kuurne
Phone: [phone]
Fax: [phone]
Support: www.barco.com/esupport
Visit us at the web: www.barco.com

1. MSWU-81E Serial Communication
MSWU-81E –2014/10/30 3
1. RLS W12 SERIAL COMMUNICATION
About this chapter
This chapter contains serial commands to control the projector.
Overview
Interface and Requirements
Cable Type and Pin definition
System Operation commands

1. MSWU-81E Serial Communication
4 MSWU-81E –2014/10/30
1.1 Interface and Requirements
Control Command Protocol
The RS-232 Commands use only ASCII characters which can be entered using a typical terminal emulator like Windows
HyperTerminal with the following setting:
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
TCP/IP communication port
The TCP/IP communication port number: 43680
1.2 Cable Type and Pin definition
Diagram:
Note:
Use Straight through RS232 cable.
Pin 9 is reserved for service purpose only.

1. MSWU-81E Serial Communication
MSWU-81E –2014/10/30 5
1.3 System Operation commands
Introduction
The Operation commands tell the projector what to do. All commands start with 2 letters: “op” for operations
commands and a space [SP] then following a control command then finally the value wants to read, set, increase or
decrease. All commands must end with a carriage return (ASCII hex 0D), shown as [CR] below. The syntax for
operations commands is as follows:
op[SP]<operation command>[SP]<Setting Value>[CR]
For all but Execute functions the response from the projector will be the command and “= <value>” where <value> is
the current value or “NA” if the value is not available. For Execute functions the response will be the same command.
All responses will be in CAPS and also ending with a carriage return (ASCII hex 0D). Please refer to the following table
for command list and examples:
System Operation Commands:
Operation
Commands
Values
Set
= <value>
Makes the unit take that value.
Get
?
Asks what the current value is.
Increment
+
Adds 1 to the current value.
Decrement
-
Subtracts 1 from the current value.
Execute
(none)
Performs an action such as a reset.
Motor operation command:
For motor control like lens shift, focus and zoom, the parameters “ + ” and “ - ” are defined as follows.
Command item
command
System Action
focus
+ -
+ => Focus Near,
- => Focus Far
zoomio
+ -
+ => Zoom out
- => Zoom in
Vert.offset
+ -
+ => Up
- => Down
horiz.offset
+ -
+ => Right
- => Left
lens.center
(execute)
Midposition shift
Get operations command example:
Input: op bright? [CR]
System Response: OP BRIGHT = 100
Increase & Decrease operations command examples:
Input: op bright + [CR]
System Response: OP BRIGHT = 101
Input: op bright - [CR]
Response: OP BRIGHT = 126
Set operations command example:
Input: op bright = 127 [CR]
System Response: OP BRIGHT = 127
Execute command example:
Input: op auto.img [CR]
Response: OP AUTO.IMG

1. MSWU-81E Serial Communication
6 MSWU-81E –2014/10/30
1.4 List of valid operations commands for Barco MSWU-81E
RLS W12 Operations Commands
No.
Operation
Commands
Values
Notes
1
input.sel
= ?
0 = HDMI
1 = HD BaseT
2 = RGB D-15
3 = YUV 1
4 = RGBHV/YUV2
5 = Reserve (CVBS)
6 = Reserve (SVIDEO)
7 = Reserve (SCART)
8 = SDI/HDSDI/3G
9 = Reserve (STEREO DVI)
Note1
Note3
2
input.lock
= ?
0 = Auto
1 = 48 Hz
2 = 50 Hz
3 = 60 Hz
Note2
3
auto.powoff
= ?
0 = Off
1 = On
4
auto.powon
= ?
0 = Off
1 = On
5
no.signal
= ?
0 = Logo
1 = Blue
2 = Black
3 = White
Note1
6
auto.imgadj
= ?
0 = Off
1 = Auto
2 = Always
Note2
7
contrast
= ? + -
0 - 200
Note2
8
Bright
= ? + -
0 - 200
Note2
9
sharp
= ? + -
0 - 200
Note2
10
nr
= ? + -
0 - 200
Note2
11
color.temp
= ?
0 = 3200K
1 = 5400K
2 = 6500K
3 = 9300K
4 = Native
Note2
Note8
12
red.offset
= ? + -
0-200
Note2
13
green.offset
= ? + -
0-200
Note2
14
blue.offset
= ? + -
0-200
Note2
15
red.gain
= ? + -
0-200
Note2
16
green.gain
= ? + -
0-200
Note2
17
blue.gain
= ? + -
0-200
Note2
18
aspect
= ?
0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
Note2
Note5

1. MSWU-81E Serial Communication
MSWU-81E –2014/10/30 7
19
h.total
= ? + -
0-200
Note2
Note7
20
h.pos
= ? + -
0-200
Note2
21
h.phase
= ? + -
0-200
Note2
Note7
22
v.pos
= ? + -
0-200
Note2
23
auto.img
(execute)
Note2
24
picture.mode
= ?
0 = Bright
1 = Presentation
2 = Video
3 = RGB Only
25
color.space2
= ?
0 = Auto
1 = YUV HD
2 = YUV STD
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
Note2
26
zoom
= ?
0 = Off
1 = Crop
2 = Zoom
Note2
Note6
27
pip.sel
= ?
1 = HDMI 1
2 = HDMI 2
3 = VGA
4 = YUV 1
5 = RGBHV/YUV2
6 = Reserve
7 = Reserve
8 = Reserve
9 = SDI/HDSDI/3G
Note1
Note9
28
pip.pos
= ?
0 = Top left
1 = Top right
2 = Bottom left
3 = Bottom right
4 = Split L-R
Note1
Note10
29
pip
= ?
0 = Off
1 = On
Note1
30
lamp.mode
= ?
0 = Economy
1 = Standard
2 = Dimming
Note2
31
lamps
= ?
0 = Single
1 = Dual
Note1
Note11
32
altitude
= ?
0 = Off
1 = On
Note1
33
lamp.pwr
= ?
W7:0(75%) ~ 20 (100%)
H8:0(80%) ~ 20 (100%)
Note2
34
lamp1.stat
?
0 = Off
1 = On
Note1
35
lamp2.stat
?
0 = Off
1 = On
Note1
36
rear.proj
= ?
0 = front
1 = rear
Note1
37
ceil.mode
= ?
0 = floor
1 = ceiling
Note1
38
zoomio
+ -
+ = Zoom out
- = Zoom in
Note1
39
focus
+ -
+ = Focus Near
- = Focus Far
Note1
40
vert.offset
+ -
+ = Up
- = Down
Note1

1. MSWU-81E Serial Communication
8 MSWU-81E –2014/10/30
41
horiz.offset
+ -
+ = Right
- = Left
Note1
42
dyna.cont
= ?
0 = Off
1 = On
Note2
43
gamma
= ?
0 = 1.8
1 = 2.0
2 = 2.2
3 = 2.35
4 = 2.5
5 = S-Curve (H8 only)
Note2
44
int.ptrn
= ?
0 = Off
1 = Color Bars
2 = Hatch
3 = Burst
4 = Red
5 = Green
6 = Blue
7 = White
8 = Black
9 = TI-Red
10 = TI-Green
11 = TI-Blue
12 = TI-Ramp
13 = Warping/Blending
Note1
45
color.space
= ?
0 = Native
1 = Reserve (EBU)
2 = Reserve (SMPTE)
3 = Custom
Note2
46
Lens.center
(execute)
Note1
47
h.keystone
= ? + -
-350~+350
Note1
Note15
48
v.keystone
= ? + -
-200~+200
Note1
Note15
49
warp.rotat
= ? + -
-20 ~ +20 (in ¼∘unit)
50
warp.pinbrl
= ? + -
-100 ~ +100
51
warp.tlc.x
= ? + -
‘x: -192 ~ +192
52
warp.tlc.y
‘y: -120 ~ +120
53
warp.trc.x
= ? + -
‘x: -192 ~ +192
54
warp.trc.y
‘y: -120 ~ +120
55
warp.blc.x
= ? + -
‘x: -192 ~ +192
56
warp.blc.y
‘y: -120 ~ +120
57
warp.brc.x
= ? + -
‘x: -192 ~ +192
58
warp.brc.y
‘y: -120 ~ +120
59
warp.reset
(execute)
60
w2.recover
(execute)
61
blank.top
= ? + -
0 ~ 360
62
blank.btm
= ? + -
0 ~ 360
63
blank.left
= ? + -
0 ~ 534
64
blank.right
= ? + -
0 ~ 534

1. MSWU-81E Serial Communication
MSWU-81E –2014/10/30 9
65
blank.rst
(execute)
66
scen.stat
= ?
0 = Off
1 = On
67
scen.wht.top
= ? + -
0 ~ 500
68
scen.wht.btm
69
scen.wht.left
= ? + -
0 ~ 800
70
scen.wht.right
71
scen.blk.top
= ? + -
0 ~ 32
72
scen.blk.btm
73
scen.blk.left
= ? + -
0 ~ 32
74
scen.blk.right
75
scen.red
= ? + -
0 ~ 32
76
scen.green
= ? + -
0 ~ 32
77
scen.blue
= ? + -
0 ~ 32
78
scen.all
= ? + -
0 ~ 32
79
scen.reset
(execute)
80
scen.adl
= ?
0 = Off
1 = On
81
brilliant.blend
= ?
0 = Off
1 = On
82
ir.addr
= ?
0 = remote code 1
1 = remote code 2
83
eco.net.pow
= ?
0 = Off (RJ45 Power On)
1 = On (RJ45 Power Off)
84
net.ipaddr
= ?
85
net.subnet
= ?
86
net.gateway
= ?
87
net.dhcp
= ?
0 = Off
1 = On
88
menu.pos
= ?
0 = Top left
1 = Top right
2 = Bottom left
3 = Bottom right
4 = center
Note1
89
startup.logo
= ?
0 = Off
1 = On
90
startup.chime
= ?
0 = Off
1 = On
91
92
93
94
95
btn.1
btn.2
btn.3
btn.4
btn.5
= ?
0 = HDMI
1 = HD BaseT
2 = VGA
3 = YUV 1
4 = RGBHV/YUV2
5 = Reserve (CVBS)
6 = Reserve (SVIDEO)
7 = Reserve (SCART)
8 = SDI/HDSDI/3G
9 = Reserve (STEREO DVI)

1. MSWU-81E Serial Communication
10 MSWU-81E –2014/10/30
96
trig.1
= ?
0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9 = Auto
Note1
97
trig.2
= ?
0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9 = Auto
Note1
98
auto.src
= ?
0 = Off
1 = On
Note1
99
lang
= ?
0 = English
1 = French
2 = Spanish
3 = German
4 = Portuese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 = Korean
9 = Russian
100
model
?
101
ser.no
?
102
sw.ver
?
Note13
103
act.src
?
0 = HDMI 1
1 = HDMI 2
2 = VGA
3 = YUV 1
4 = RGBHV/YUV2
5 = Reserve
6 = Reserve
7 = Reserve
8 = SDI/HDSDI/3G
Note1
104
pip.src
?
0 = HDMI 1
1 = HDMI 2
2 = VGA
3 = YUV 1
4 = RGBHV/YUV2
5 = Reserve
6 = Reserve
7 = Reserve
8 = SDI/HDSDI/3G
Note1
105
pixel.clock
?
Note2
106
signal
?
Note2
107
h.refresh
?
Note2