Barco HDX 4K User manual

R5906069 /01
HDX 4K
Quick Start Guide
Install Lens & Lens safety cable !! ONLY USE TLD+ Zoom Lenses !!
1. Remove the plastic cover from the Lens Holder opening.
2. Place the Lens Holder in unlock position. Handle towards electrical socket.
3. Gently insert the lens. Ensure the lens connector matches the electrical socket on the Lens Holder.
4. Insert the lens until the connector seats into the socket.
5. Secure the lens in the Lens Holder. Move the handle into the lock position.
6. Check if the lens touches the front plate of the Lens Holder.
7. Check if the lens is really secured by trying to pull the lens out of the Lens Holder.
8. Install the lens safety cable tightly around the lens. Keep safety cable as short as possible.
9. Attach lens safety cable with projector frame. Keep safety cable as short as possible.
Connect power
Ensure that the power is properly connected to the powerinput.
(110-130V / 200-240V, 15A, 50-60Hz)
Download Product Manual
Product manuals and documentation are available online at www.barco.com/td/R9012100
Registration may be required; follow the instructions given on the website.
IMPORTANT!
Read Installation Instructions before connecting equipment to the mains power supply.

- 2 -
2. Orientation of the unit is set as standard in table front projection mode.
Change the projector set up in the ALIGNMENT > ORIENTATION menu.
3. For Advanced adustments like Warping, Light management, etc. see User Guide of the projector.
Adjust
1. Adjust the lens settings by pressing the LENS button or via the direct lens keys on the RCU.
Select the “Greenfocus” test pattern to adjust the lens.
Connect and Select source
1. Connectavailable sourcesto the appropriate inputports.
2. Select connected source:
- The LED of the selected source lit up GREEN.
- Image of selected inputappears.
2
1
1
Startup
1. Power on. Turn the mains switch to on ( I ).
- Start up sequence starts. Backlight of the Power on/off button flashes WHITE.
2. Press the Power on/off button.
- The backlight of the Power on/off button changes from WHITE to BLUE.
- Local LCD displays a start up screen.
12

- 3 -
Switch off
1. Press the Power on/off button for three seconds.
2. Wait until the after-cooling cycle is finished (up to 300 sec.)
3. Turn the mains switch to off (’0’).
4. Unplug the power cord from the projector.
321
300 s
3 s
4
Local Keypad
1MenuNavigation.
2MenuSelection.
3Open Menu.
4MenuBack.
5Power On/Off.
6OSD On/Off.
7InputSelection.
8Shutter Open/Close.
9Test Patterns.
10 Lens Menu.
11 Touch Panel.
1 2 3 4 5 6
1011 9 8 7
• Remove the lens before transporting the projector.
• First switch the projector to Standby mode and wait until After Cooling is
finished to switch off the main power.
• Ensure the projector is operating with clean filters.
• Do not block the ventilation in and outlets.
• Laser light can cause severe damage to the DMD. This damage is
not covered by warranty.
Precautions

- 4 -
RCU buttons
1Button pressed indicator.
13 Numeric buttons.
2Shutter Open.
14 XLR connector.
3Shutter Close.
15 Macro button.
4Touch Panel On/Off.
16 MenuBack.
5LCD On/Off.
17 Defaultbutton.
6Lens Zoom.
18 Lens Focus.
7Lens Shift.
19 Color On/Off.
8Menu Activation.
20 Test Patterns.
9Menu Selection.
21 Power On.
10 Menu Navigation.
22 Power Off.
11 Input Selection.
23 Stereo Jack.
12 Address button.
24 RCU On/Off.
1
2
3
4
5
6
7
8
9
10
11
12
14
22
21
20
19
18
17
16
15
13
24
23

- 5 -
Communication Panel
321 4 5 6 7 8 9 10 11 12 13
1WiFi antenna for wireless IP (optional) 8RS232 for serial communication
212V 1A output 9Sync Out
3Firmware update/USB backup custom settings 10 Sync In
410/100 base-T for external control over IP and Art-Net 11 Status lights
5DMX interface input 12 IR receive sensor
6DMX interface output 13 GSM antenna input (optional)
7XLR input for wired projector control
Venues & Hospitality Input (V&H)
SELSELSELSELSELSELSEL
TUO/NIIDSNIIDS
SEL
SYNC
A
SYNC
B
SYNC
C
SYNC
D
DP HDMI
SYNC
HDBT 1
SYNC
HDBT 2
SYNCSYNC
1 2 3 4 5 6 7 8
1Quad 3G SDI channel A Input 5DisplayPort Input
2Quad 3G SDI channel B Input 6HDMI Input
3Quad 3G SDI channel C Input/Output 7HDBaseT Input 1
4Quad 3G SDI channel D Input/Output 8HDBaseT Input 2
Virtual & Augmented Reality Input (V&AR) (Optional)
SELSELSELSEL
DP A DP B DP C DP D
SYNCSYNCSYNCSYNC
1 2 3 4
1Quad DisplayPort channel A Input 3Quad DisplayPort channel C Input
2Quad DisplayPort channel B Input 4Quad DisplayPort channel D Input

- 6 -
- 6 -
Button Backlight Status
Button Color status Description
Projector starts up (Booting)Blinking WHITE
Projector is in StandbySolid WHITE
Blinking RED Error condition
Blinking BLUE Projectorgoes to ON mode
Projector is ON
Power button
Solid BLUE
Off Projector not in power ON state
Solid WHITE Shutter is open
Shutter is closedSolid RED
Shutter button
LED Status
LED Color status Description
Off Projector powers up
Projector is in StandbyRED
Projector is ReadyORANGE
PWR (power LED)
GREEN Projector is on
Lamp is offOff
No lamp insertedRED
Lamp is on in ECO mode
ORANGE
GREEN Lamp is on in normal mode
LIGHT (Illumination LED)
Lamp is on in CLO modeGREEN-ORANGE
Off No error
RED toggleson/off Error
ERR (error LED)
ORANGE toggleson/off Warning
IR signal receivedREDIR
GREEN IR signal acknowledged
Support
Website www.barco.com/esupport
- USA [phone]
- EMEA [phone]
- APAC [phone]
Tel.: