Basler daA2500-60mc-SD820-DB8 User manual

QUICK INSTALL GUIDE
BASLER EMBEDDED VISION KIT
daA2500-60mc-SD820-DB8

Basler AG
An der Strusbek 60–62
22926 Ahrensburg
Germany
All material in this publication is subject to change without notice and is
copyright Basler AG.

3
TABLE OF CONTENTS
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Target Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DELIVERED PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HARDWARE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Overview of the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the Embedded Vision Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ACQUIRING YOUR FIRST IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NEXT STEPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Developer Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4
TABLE OF CONTENTS
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Processing Board Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Mezzanine Board Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Lens Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Power Supply Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Block Diagram of the Mezzanine Board . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DISCLAIMER AND LICENSING INFORMATION . . . . . . . . . . . . . . . . . . . . . 19
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Software Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5
INTRODUCTION
INTRODUCTION
About this Document
This document provides information about how to install the daA2500-
60mc-SD820-DB8 Embedded Vision Kit. It also provides step-by-step
instructions that help you acquire your first images with the included Basler
dart BCON for MIPI camera.
Target Audience
The daA2500-60mc-SD820-DB8 Embedded Vision Kit is aimed at
experienced hardware and software engineers proficient in electronics,
software development, and embedded system design.
This document is written for a target audience that has intermediate to
advanced technical skills in the areas mentioned above.
The document assumes that users have experience in the following areas:
System on Chip (SoC) or System on Module (SoM) architectures
Embedded Linux operating systems

6
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
General Safety Notices
DANGER
Electric Shock Hazard: Unapproved power supplies may cause electric
shock. Serious injury or death may occur.
Only use the power supply delivered with the Embedded Vision Kit. Do not
use other power supplies.
WARNING
Fire Hazard: Unapproved power supplies may cause fire and burns.
Only use the power supply delivered with the Embedded Vision Kit. Do not
use other power supplies.
NOTICE
Damage Hazard: Electrostatic discharge (ESD) can damage the
components of the Embedded Vision Kit.
Use anti-static clothes and materials, e.g., conductive shoes, anti-static
gloves, and ESD protection wrist straps to decrease the risk of
electrostatic discharge.
Control the humidity in your environment. Low humidity can cause ESD
problems.

NOTICE
7
SAFETY INSTRUCTIONS
Radio Interference Hazard: This is a Class A product. In residential
environments, this product may cause radio interference, in which case the
user may be required to take adequate measures.
Observe the following items:
Do not modify the hardware components in any way. Do not remove
parts from the board or solder in new parts.
Do not allow, e.g., liquid, flammable, or metallic material to get in
contact with the boards.
Read the documentation carefully before using the Embedded Vision
Kit.
For safety instructions related to the operation of the Basler dart BCON
for MIPI camera, refer to the Basler Product Documentation available at
docs.baslerweb.com.

8
SAFETY INSTRUCTIONS
Environmental Requirements
This Embedded Vision Kit is intended for indoor use at normal room
temperature only.
If you operate the Embedded Vision Kit at elevated temperatures or at high
load, Basler recommends providing additional cooling, e.g., by installing a
fan.
For specific environmental requirements of the components, refer to the
Basler Product Documentation available at docs.baslerweb.com.

9
DELIVERED PARTS
DELIVERED PARTS
The daA2500-60mc-SD820-DB8 Embedded Vision Kit contains the
following components:
Basler dart daA2500-60mc camera module, S-mount
Evetar lens N118B05518W ƒ/1.8, f5.5 mm, 1/1.8"
Developer Board 8 processing board
Basler dart BCON for MIPI mezzanine board, pre-mounted on the
processing board
Flexible flat cable, 0.2 m
USB 2.0 cable (A / Micro B), 1.8 m
HDMI 2.0 cable (A / A), 1.5 m
GigE cable Cat 5e, 2.0 m
Power supply, 18 W, 12 V @ 1.5 A
International power cable plugs (see page 17 for details)
Mounting kit (including camera mounting plate, spacer bolts, screws,
and nuts)
Basler dart Getting Started Guide
This Quick Install Guide

10
HARDWARE INSTALLATION
HARDWARE INSTALLATION
Overview of the Components
RQC180203 VER1.0
GND
SDA
SCL
GND
GND
IO-
1V8
SCL
POWER RESET
CAM_PWR
POWER RESET
CAM_PWR
Processing
board
USB 2.0
port
Power LED
(CAM PWR)
Reset button
Basler
dart BCON for
MIPI
camera with
S-mount lens
Power LED
(LED1)
USB 3.0
ports
Power supply
port
GigE
port
Spacer
bolt
Mounting
plate
FFC
connectors
Flexible
flat cable
microSD
card slot
HDMI
port
Mezzanine
board
Power button
Fig. 1: daA2500-60mc-SD820-DB8 – Installed Hardware Components